Revealing the high strength and high thermal stability of a nano-lamellar Cu-0.1 at.% Zr alloy
Source abstract
Abstract
Nano-lamellar structured Cu-0.1 at.% Zr alloys are prepared by the combination of equal channel angular pressing and subsequent cryogenic rolling. The advanced processing route enables a systematic reduction of the lamellae boundary spacing down to 45 nm and a concurrent increase of yield strength up to 626 MPa. Subsequent annealing at temperatures up to 673 K induced recovery processes and uniform coarsening through triple junction motion, avoiding a catastrophic degradation of the microstructure and performance and preserving the yield strength at a level comparable to ultrafine-grained copper. Simultaneously, the tensile uniform elongation experienced a substantial recovery up to 11.9 %. The high thermal stability is mainly attributed to the low mobility of grain boundary and the relaxation of non-equilibrium grain boundaries, both of which are facilitated by the microalloying of Cu with Zr. Based on the theory of dislocation pile-up at boundaries, the Hall-Petch equation is adopted and extended to the lamellar structured Cu-0.1 at.% Zr alloy, revealing a lower-critical bound of 90 nm for lamellae boundary spacing, corresponding to an effective boundary spacing of about 150 nm.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloys Composites Properties · Metallic Glasses and Amorphous Alloys
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (72)
Show source-provided references
1. Strain-induced ultrahard and ultrastable nanolaminated structure in nickel10.1126/science.1242578 ↗
2. Segregation and precipitation stabilizing an ultrafine lamellar structured Al-0.3%Cu alloy10.1016/j.actamat.2020.116595 ↗
3. Processing of bulk nanolamellar tantalum and justification of strengthening by grain boundary pre-stressed model10.1016/j.ijplas.2021.102939 ↗
4. Revealing the maximum strength in nanotwinned copper10.1126/science.1167641 ↗
5. Strengthening mechanisms and Hall-Petch stress of ultrafine grained Al-0.3%Cu10.1016/j.actamat.2018.07.006 ↗
6. Preparation of bulk nanolaminated aluminum alloy with high strength10.1016/j.msea.2019.138556 ↗
7. The scale effect on the yield strength of nanocrystalline materials10.1016/j.ijsolstr.2006.04.015 ↗
8. On the effect of grain size on yield stress: extension into nanocrystalline domain10.1016/S0921-5093(00)02029-3 ↗
9. The hall-petch relationship in nanocrystalline iron produced by ball milling10.1016/0956-716X(90)90439-N ↗
10. The deformation and ageing of mild steel: III discussion of results10.1088/0370-1301/64/9/303 ↗
11. The cleavage strength of polycrystals
12. On the mechanism of work hardening in face-centred cubic metals, with special reference to polycrystalline copper
13. The effect of grain size on the high-strain, high-strain-rate behavior of copper10.1007/BF02669646 ↗
14. Structure and mechanical behavior of bulk nanocrystalline materials10.1557/S088376940005154X ↗
15. Reaching theoretical strengths in nanocrystalline Cu by grain boundary doping10.1016/j.scriptamat.2011.06.048 ↗
16. Effect of cold rolling on microstructure and mechanical properties of copper subjected to ECAP with various numbers of passes10.1016/j.msea.2012.06.022 ↗
17. Plastic anisotropy and associated deformation mechanisms in nanotwinned metals10.1016/j.actamat.2012.09.052 ↗
18. Tensile behavior of columnar grained Cu with preferentially oriented nanoscale twins10.1016/j.actamat.2011.07.044 ↗
19. Revealing the maximum strength in nanotwinned copper10.1126/science.1167641 ↗
20. Tensile behavior and flow stress anisotropy of accumulative roll bonded Cu-Nb nanolaminates10.1063/1.4941043 ↗
21. Impurity effect on recrystallization and grain growth in severe plastically deformed copper10.1016/j.msea.2021.141786 ↗
22. An investigation on rolling texture transition in copper preprocessed by equal channel angular pressing10.1007/s10853-016-9862-2 ↗
23. Grain size dependent texture evolution in severely rolled pure copper10.1016/j.matchar.2015.02.003 ↗
24. Microstructure of equal-channel angular pressed Cu and Cu-Zr samples studied by different methods10.1007/s11661-009-9895-0 ↗
25. Effect of deformation schedules and initial states on structure and properties of Cu–0.18% Zr alloy after high-pressure torsion and heating10.1016/j.msea.2013.12.104 ↗
26. Ultra-fast diffusion channels in pure Ni severely deformed by equal-channel angular pressing10.1016/j.actamat.2010.11.063 ↗
27. A comparison of microstructures and mechanical properties in a Cu–Zr alloy processed using different SPD techniques10.1007/s10853-012-7072-0 ↗
28. Heterogeneous structure controlled by shear bands in partially recrystallized nano-laminated copper10.1016/j.msea.2018.02.098 ↗
29. Exceptional thermal stability of additively manufactured CoCrFeMnNi high-entropy alloy with cellular dislocation structures10.1016/j.msea.2023.145650 ↗
30. A multiscale architectured CuCrZr alloy with high strength, electrical conductivity and thermal stability10.1016/j.jallcom.2017.11.309 ↗
31. Kinetics of grain boundary recovery in deformed polycrystals10.1023/A:1008720710330 ↗
32. Reaching unconventionally large Hall-Petch coefficients in face-centered cubic high-entropy alloys10.1080/21663831.2024.2337211 ↗
33. Recovery and recrystallization in commercial purity aluminum cold rolled to an ultrahigh strain10.1016/j.actamat.2013.05.024 ↗
34. Linking recovery and recrystallization through triple junction motion in aluminum cold rolled to a large strain10.1016/j.actamat.2013.07.040 ↗
35. TEM study of recovery and recrystallization mechanisms after 40% cold rolling in an IF-Ti steel10.1016/j.scriptamat.2005.06.025 ↗
36. Importance of non-uniform boundary migration for recrystallization kinetics10.1007/s11661-018-4846-2 ↗
37. Atomic scale studies of solute-atom segregation at grain boundaries: experiments and simulations10.1016/0022-3697(94)90123-6 ↗
38. Nanostructure of aluminium alloy 2024: segregation, clustering and precipitation processes10.1016/j.actamat.2010.11.033 ↗
39. Intrinsic heterogeneity of grain boundary phase transitions in the Cu–Bi system: insights from grain boundary diffusion measurements10.1515/ijmr-2023-0174 ↗
40. Optimization of the balance between high strength and high electrical conductivity in CuCrZr alloys through two-step cryorolling and aging10.1016/j.jallcom.2018.09.040 ↗
41. Microstructural inhomogeneities in Cu–Ag–Zr alloys due to heavy plastic deformation10.1016/j.msea.2009.08.036 ↗
42. A promising structure for fabricating high strength and high electrical conductivity copper alloys
43. Deformation behaviour of ultra-fine-grained copper10.1016/0956-7151(94)90326-3 ↗
44. Neumann · 2011
45. Grain boundary self-diffusion in Cu polycrystals of different purity10.1016/S1359-6454(97)00037-2 ↗
46. Diffusion, solute segregations and interfacial energies in some material: an overview10.1023/A:1021570503733 ↗
47. Determination of volume and grain boundary heterodiffusion coefficients of silver in pure copper, and effects of the alloying elements chromium, tellurium, titanium, and ziconium on these coefficients
48. Ag grain boundary diffusion and segregation in Cu: measurements in the types B and C diffusion regimes10.1016/S1359-6454(00)00304-9 ↗
49. Subgrain growth in heavily deformed aluminium–experimental investigation and modelling treatment10.1016/0956-7151(94)00410-2 ↗
50. Gibbs · 1948
51. Grain boundary self-diffusion in polycrystalline nickel of different purity levels10.1016/j.actamat.2009.09.015 ↗
52. Grain boundary width, energy and self-diffusion in nickel: effect of material purity10.1016/j.actamat.2013.05.010 ↗
53. Diffusion in the Cu-Ag system-hetero-diffusion and chemical diffusion-influence of small additions of Cr, Te, Ti and Zr to the Cu
54. Effect of atomic interaction on grain boundary diffusion in the B regime10.1016/j.actamat.2012.06.011 ↗
55. Persistence of ultrafast atomic diffusion paths in recrystallizing ultrafine grained Ni10.1016/j.scriptamat.2015.01.027 ↗
56. Grain-boundary melting phase transition in the Cu-Bi system10.1103/PhysRevB.71.104104 ↗
57. D. McLean, Grain boundaries in metals, (1957).
58. Alloy effects in nanostructures10.1016/0965-9773(93)90088-S ↗
59. Identifying interatomic potentials for the accurate modeling of interfacial segregation and structural transitions10.1016/j.commatsci.2018.02.020 ↗
60. Hall-Petch relation and boundary strengthening10.1016/j.scriptamat.2004.06.002 ↗
61. A statistical theory of solid solution hardening10.1002/pssb.19700410221 ↗
62. Solid solution strengthening and deformation behavior of single-phase Cu-base alloys under tribological load10.1016/j.actamat.2019.12.005 ↗
63. Insight into the influence of alloying elements on the elastic properties and strengthening of copper: a high-throughput first-principles calculations10.3390/met13050875 ↗
64. Theory of plastic deformation: properties of low energy dislocation structures10.1016/0921-5093(89)90290-6 ↗
65. The type of dislocation interaction as the factor determining work hardening10.1016/0025-5416(80)90175-5 ↗
66. From dislocation junctions to forest hardening10.1103/PhysRevLett.89.255508 ↗
67. Significant Hall–Petch effect in micro-nanocrystalline electroplated copper controlled by SPS concentration10.1038/s41598-023-27669-2 ↗
68. Grain boundary strengthening of copper-base copper–manganese and copper–gallium solid solutions10.1016/S1359-6454(97)00451-5 ↗
69. Analysis of strengthening due to grain boundaries and annealing twin boundaries in the CrCoNi medium-entropy alloy10.1016/j.ijplas.2019.08.009 ↗
70. Grain boundaries and bdiffusion phenomena in severely deformed materials10.2320/matertrans.MF201934 ↗
71. Limits of hardness at the nanoscale: molecular dynamics simulations10.1103/PhysRevB.78.241402 ↗
72. The impact of precipitation on recrystallization in a severely plastically deformed CoCrFeMnNi multi–principal element alloy10.1016/j.matchar.2024.113910 ↗