Plastic deformation of single crystals of the equiatomic Cr−Mn−Fe−Co−Ni high-entropy alloy in tension and compression from 10 K to 1273 K
Source abstract
Abstract
Abstract The plastic deformation behavior of single crystals of the quinary, equiatomic Cr−Mn−Fe−Co−Ni high-entropy alloy (HEA) with the face-centered cubic structure has been investigated in tension and compression as a function of crystal orientation and temperature from 10 K to 1373 K. The critical resolved shear stress (CRSS) for {111} slip at room temperature is 42−45 MPa. It does not depend much on crystal orientation (i.e., the Schmid law holds true) and the sense (tension vs. compression) of the applied load. The CRSS for {111} slip increases with the decrease in temperature, without showing any significant inertia effects at cryogenic temperatures below 77 K. Extrapolation from the measured yield stresses down to 10 K yields a CRSS value at 0 K of 168 MPa. At cryogenic temperatures, the measured strain-rate sensitivity of flow stress is consistent with a very small activation volume. The concept of stress equivalence holds true both for the temperature dependence of CRSS and the stress dependence of activation volume, indicating that solid-solution hardening is the major strengthening mechanism. Deformation twinning occurs at 77 K but not at room temperature, resulting in higher tensile elongation to failure at 77 K than at room temperature. Deformation twinning at 77 K occurs at a shear stress of 378 MPa on conjugate ( 1 ¯ 1 ¯ 1) planes in the form of Luders deformation after large plastic strain (about 85%) achieved by the stage I (easy glide) and stage II (linear work-hardening) deformation.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Entropy Alloys Studies · High-Temperature Coating Behaviors · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (54)
Show source-provided references
1. Nanostructured high-entropy alloys with multiple principal elements: novel alloy design concepts and outcomes10.1002/adem.200300567 ↗
2. High-entropy alloys; A critical review10.1080/21663831.2014.912690 ↗
3. A critical review of high entropy alloys and related concept10.1016/j.actamat.2016.08.081 ↗
4. A review on fundamental of high entropy alloys with promising high–temperature properties10.1016/j.jallcom.2018.05.067 ↗
5. High-entropy alloys10.1038/s41578-019-0121-4 ↗
6. High entropy alloys: a focused review of mechanical properties and deformation mechanisms10.1016/j.actamat.2019.12.015 ↗
7. Microstructural development in equiatomic multicomponent alloys10.1016/j.msea.2003.10.257 ↗
8. Tensile properties of high-and medium-entropy alloys10.1016/j.intermet.2013.03.018 ↗
9. The influences of temperature and microstructure on the tensile properties of a CoCrFeMnNi high-entropy alloy10.1016/j.actamat.2013.06.018 ↗
10. A fracture resistant high-entropy alloy for cryogenic applications10.1126/science.1254581 ↗
11. Modelling solid solution hardening in high entropy alloys10.1016/j.actamat.2014.11.014 ↗
12. A general formulation for solid solution hardening effect in multicomponent alloys10.1016/j.scriptamat.2016.09.009 ↗
13. Theory of strengthening in fcc high entropy alloys10.1016/j.actamat.2016.07.040 ↗
14. Solute strengthening in random alloys10.1016/j.actamat.2016.09.046 ↗
15. Atomic displacement in the CrMnFeCoNi high-entropy alloy –A scaling factor to predict solid solution hardening10.1063/1.4971371 ↗
16. Microstructure evolution and critical stress for twinning in the CrMnFeCoNi high-entropy alloy10.1016/j.actamat.2016.07.038 ↗
17. The onset of twinning in metals: a constitutive description10.1016/S1359-6454(01)00300-7 ↗
18. Predicting twinning stress in fcc metals: linking twin-energy pathways to twin nucleation10.1016/j.actamat.2007.08.042 ↗
19. Slip nucleation in single crystal CoCrFeMnNi high-entropy alloy10.1016/j.scriptamat.2015.09.009 ↗
20. Critical resolved shear stress for slip and twin nucleation in single crystalline FeNiCoCrMn high entropy alloy10.1016/j.matchar.2017.05.014 ↗
21. Orientation dependence of twinning in single crystalline CoCrFeMnNi high-entropy alloy10.1016/j.msea.2017.08.065 ↗
22. Experimental determination of latent hardening coefficients in FeMnNiCoCr10.1016/j.ijplas.2018.02.016 ↗
23. Twinning in [001]-oriented single crystals of CoCrFeMnNi high-entropy alloy at tensile deformation10.1016/j.msea.2017.12.059 ↗
24. Hardening by slip-twin and twin-slip interactions in FeMnNiCoCr10.1016/j.actamat.2018.04.054 ↗
25. Temperature dependence of the mechanical properties of equiatomic solid solution alloys with face-centered cubic crystal structures10.1016/j.actamat.2014.08.026 ↗
26. Size effect, critical resolved shear stress, stacking fault energy, and solid solution strengthening in the CrMnFeCoNi high-entropy alloy10.1038/srep35863 ↗
27. Entropy determination of single-phase high entropy alloys with different crystal structures over a wide temperature range10.3390/e20090654 ↗
28. Effects of ordering on the properties of Ni-Cr alloys10.1007/BF01115776 ↗
29. Hydrogen enhanced localization of plasticity in an austenitic stainless steel10.1007/BF02669644 ↗
30. Effect of short-range ordering in stress corrosion cracking susceptibility of alloy 600 studied by electron and neutron diffraction10.1016/j.actamat.2014.10.009 ↗
31. Monocrystalline elastic constants of fcc-CrMnFeCoNi high entropy alloy10.1557/adv.2017.76 ↗
32. Mechanical properties and stacking fault energies of NiFeCrCoMn high-entropy alloy10.1007/s11837-013-0771-4 ↗
33. Calculating elastic constants in high-entropy alloys using the coherent potential approximation: current issues and errors10.1016/j.commatsci.2015.09.058 ↗
34. Effect of alloying on the thermal-elastic properties of 3d high entropy alloys10.1016/j.matchemphys.2017.10.046 ↗
35. Simmons · 1971
36. Temperature dependencies of the elastic moduli and thermal expansion coefficient of an equiatomic, single-phase CoCrFeMnNi high-entropy alloy10.1016/j.jallcom.2014.11.061 ↗
37. Polycrystalline elastic moduli of a high-entropy alloy at cryogenic temperatures10.1016/j.intermet.2014.11.005 ↗
38. Decomposition of the single-phase high-entropy alloy CrMnFeCoNi after prolonged anneals at intermediate temperatures10.1016/j.actamat.2016.04.005 ↗
39. Thermally activated glide in face-centered cubic alloys
40. Investigations of the yield region of concentrated Cu−Ge and Cu−Zn single crystals-I. Critical resolved shear stress, slip line formation and the true strain rate10.1016/0001-6160(77)90234-6 ↗
41. Thermally activated deformation and the rate controlling mechanism in CoCrFeMnNi high-entropy alloy10.1016/j.msea.2016.11.078 ↗
42. Thermal activation parameters of plastic flow reveal deformation mechanisms in the CrMnFeCoNi high entropy alloy10.1016/j.actamat.2017.10.014 ↗
43. On the strain rate-dependent deformation mechanism of CoCrFeMnNi high-entropy alloy at liquid nitrogen temperature10.1080/21663831.2017.1323807 ↗
44. The evolution of the deformation substructure in a Ni-Co-Cr equiatomic solid solution alloy10.1016/j.actamat.2017.04.033 ↗
45. Magnetically-driven phase transformation strengthening in high entropy alloys10.1038/s41467-018-03846-0 ↗
46. Stress equivalence of solution hardening10.1016/0036-9748(72)90052-X ↗
47. Atomic-scale characterization and modeling of 60° dislocations in a high-entropy alloy10.1016/j.actamat.2016.03.045 ↗
48. The weak beam technique as applied to the determination of the stacking-fault energy of copper10.1080/14786437108217418 ↗
49. The measurement of stacking-fault energies of pure face-centered cubic metals10.1080/14786437108217419 ↗
50. Observations of constrictions on dissociated dislocation lines in copper alloys10.1080/14786437408226609 ↗
51. the formation and glide of jogs in low stacking-fault energy face-centered cubic materials10.1080/14786437708232974 ↗
52. The extension of jogs on dissociated dislocations in F.C.C. metals10.1002/pssa.2210540150 ↗
53. Anderson · 2017 · 455
54. Sluggish diffusion in Co–Cr–Fe–Mn–Ni high-entropy alloys10.1016/j.actamat.2013.04.058 ↗