journal article·2018-04Open access

The effects of microstructure and microtexture generated during solidification on deformation micromechanism in IN713C nickel-based superalloy

G. Liu, J. Salvat Cantó, S. Winwood, K. Rhodes, S. Birosca

Acta Materialia· Volume 148

Abstract

Abstract Nickel-based superalloy IN713C produced through investment casting route is widely used for turbocharger turbine wheels in the automotive industry. The produced microstructure and microtexture are not homogeneous across the turbine component due to geometrical factors and localised cooling rate during the casting process, which give rise to inhomogeneous deformation during service. In the present paper, two kinds of in-house fatigue tests, Low Cycle Fatigue (LCF) and High Cycle Fatigue (HCF), were conducted at 600 °C in attempt to simulate the actual fatigue conditions experienced by turbine wheels in turbocharger. From Geometrically Necessary Dislocation (GND) distributions and strain analyses, it is concluded that microstructure heterogeneity such as carbide precipitates distribution within dendritic structure network determine the failure micromechanics during LCF tests. In the early stage of LCF loading, crack principally initiated within near surface carbides that have been oxidised during high temperature exposure. The higher GND density at the tip of carbide precipitates due to oxidation volume expansion are found to facilitate easy cracks initiation and propagation. Moreover, the cluster-like carbides network and its distribution can accelerate oxidation process and crack growth effectively. Furthermore, in the later stage of crack propagation during LCF, the weak interdendrite areas rotate to accommodate increased strain leading to faster cracks propagation and hence final catastrophic failure. Serial section technique for 3-D visualisation was employed to investigate the crystallographic grain orientation correlation with fracture mechanics during HCF loading. It appears that the microtexure and grain orientations are more critical than the alloy microstructure in an area with a relatively uniform carbides distribution and weak dendrite structure where HCF failure occurred. Based on the slip trace analysis, it was found that most faceting occurred in Goss grains ( //LD) and on slip system with the highest Schmid factor. It is concluded that cracks were initiated on planes with high Schmid factors and assisted by the presence of porosity.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Temperature Alloys and Creep · Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (38)

Show source-provided references
1. The microstructure degradation of the IN 713C nickel-Based Superalloy after the stress rupture tests10.1007/s11665-014-1123-4 ↗
2. Deformation mechanisms of IN713C nickel based superalloy during Small Punch Testing10.1016/j.msea.2015.10.056 ↗
3. Fatigue behaviour of the superalloy IN 713C under LCF-, HCF- and superimposed LCF/HCF-loading10.1016/j.proeng.2010.03.146 ↗
4. High-cycle fatigue of Ni-base superalloy Inconel 713LC10.1016/j.ijfatigue.2009.02.042 ↗
5. Casting defects and high temperature fatigue life of IN 713LC superalloy10.1016/j.ijfatigue.2011.12.002 ↗
6. Inhomogeneous dislocation structure in fatigued INCONEL 713 LC superalloy at room and elevated temperatures10.1016/j.msea.2005.01.058 ↗
7. Competition between three damaging mechanisms in the fractured surface of an Inconel 713 superalloy10.1016/j.matchar.2007.08.004 ↗
8. Initiation and propagation behaviour of microcracks in Ni-base superalloy Udimet 720 Li10.1016/S0013-7944(98)00003-4 ↗
9. High cycle fatigue behavior of a directionally solidified Ni-base superalloy DZ951
10. Oxidation ahead of a crack tip in an advanced Ni-based superalloy10.1016/j.actamat.2012.12.017 ↗
11. Short crack initiation and growth at 600 °C in notched specimens of Inconel71810.1016/S0921-5093(02)00169-7 ↗
12. Failure of metals II: fatigue10.1016/j.actamat.2015.05.050 ↗
13. On the role of boron on improving ductility in a new polycrystalline superalloy10.1016/j.actamat.2016.11.009 ↗
14. Microstructural degradation of polycrystalline superalloys from oxidized carbides and implications on crack initiation10.1016/j.scriptamat.2017.12.028 ↗
15. A quantitative approach to study the effect of local texture and heterogeneous plastic strain on the deformation micro-mechanism in RR1000 nickel-based superalloy10.1016/j.actamat.2014.04.039 ↗
16. Orientation gradients and geometrically necessary dislocations in ultrafine grained dual-phase steels studied by 2D and 3D EBSD10.1016/j.msea.2010.01.004 ↗
17. High resolution electron back-scatter diffraction analysis of thermally and mechanically induced strains near carbide inclusions in a superalloy10.1016/j.actamat.2010.09.030 ↗
18. Stress fields and geometrically necessary dislocation density distributions near the head of a blocked slip band10.1016/j.actamat.2012.07.004 ↗
19. Microstructurally sensitive crack nucleation around inclusions in powder metallurgy nickel-based superalloys10.1016/j.actamat.2016.07.023 ↗
20. On the mechanistic basis of fatigue crack nucleation in Ni superalloy containing inclusions using high resolution electron backscatter diffraction10.1016/j.actamat.2015.06.035 ↗
21. Some geometrical relations in dislocated crystals10.1016/0001-6160(53)90054-6 ↗
22. The deformation of plastically non-homogeneous materials10.1080/14786437008238426 ↗
23. Crystallographic aspects of geometrically-necessary and statistically-stored dislocation density10.1016/S1359-6454(99)00020-8 ↗
24. Microstructure of individual grains in cold-rolled aluminium from orientation inhomogeneities resolved by electron backscattering diffraction10.1016/j.msea.2007.10.092 ↗
25. Determination of elastic strain fields and geometrically necessary dislocation distributions near nanoindents using electron back scatter diffraction10.1080/14786430903304145 ↗
26. Measurement of geometrically necessary dislocation density with high resolution electron backscatter diffraction: effects of detector binning and step size10.1016/j.ultramic.2012.11.003 ↗
27. Nickel-based superalloys for advanced turbine engines: chemistry, microstructure, and properties10.2514/1.18239 ↗
28. Experimental and computational studies of low cycle fatigue crack nucleation in a polycrystal10.1016/j.ijplas.2006.07.001 ↗
29. Engel · 1981 · 271
30. Cast microstructure of Inconel 713C and its dependence on solidification variables10.1007/BF02913844 ↗
31. Evolution of dislocation density distributions in copper during tensile deformation10.1016/j.actamat.2013.08.027 ↗
32. A theory of the fracture of metals10.1080/00018735700101406 ↗
33. Microstructure-sensitive fatigue crack nucleation in a polycrystalline Ni superalloy10.1016/j.ijfatigue.2016.04.013 ↗
34. Prediction of crack growth in a nickel-based superalloy under fatigue-oxidation conditions10.1016/j.engfracmech.2010.02.005 ↗
35. Crystallographic fatigue crack initiation in nickel-based superalloy René 88DT at elevated temperature10.1016/j.actamat.2009.08.022 ↗
36. The role of microtexture on the faceted fracture morphology in Ti–6Al–4V subjected to high-cycle fatigue10.1016/j.actamat.2010.03.036 ↗
37. Fatigue fracture at bicrystal interfaces: experiment and theory10.1016/S1359-6454(97)00430-8 ↗
38. Analysis of activated slip systems in fatigue nickel polycrystals using the EBSD-technique in the scanning electron microscope10.1016/0921-5093(95)10076-8 ↗