Elucidating microstructural evolution and strengthening mechanisms in nanocrystalline surface induced by surface mechanical attrition treatment of stainless steel
Source abstract
Abstract
Surface mechanical attrition treatment (SMAT) is a high strain and strain rate severe plastic deformation (SPD) technique for surface nanocrystallization of metals. The aim of this study was to investigate the mechanism of nanocrystallization and strengthening in a medium stacking fault energy 316 L austenitic stainless steel during SMAT. The paramount role of microband and shear band formation in nano crystallization is outlined, as opposed to deformation twinning previously reported in low SFE austenitic stainless steels. Shear bands undergo dynamic recrystallization and recrystallization twinning to produce ultra-fine grains in contrast to twin-twin intersections in low SFE stainless steel. The ultra-fine grains further sub-divide into smaller cells with initially low misorientation. Nanocrystallization occurs when misorientation between these cells increases with further strain. The additivity of strengthening by dislocation density and grain size is studied. Dislocation density was neglected in previous studies while studying strengthening mechanisms in SMAT processed materials. This study illustrates that dislocation density cannot be ignored as the strengthening mechanism in SMAT process. The grain size and dislocation density both significantly contribute to overall strengthening in SMAT processed microstructure. (C) 2016 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Surface Treatment and Residual Stress · Erosion and Abrasive Machining · High-Velocity Impact and Material Behavior
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (51)
Show source-provided references
1. Nanostructured surface layer on metallic materials induced by surface mechanical attrition treatment10.1016/j.msea.2003.10.261 ↗
2. Fatigue behavior of a low-alloy steel with nanostructured surface obtained by severe shot peening10.1016/j.engfracmech.2011.06.011 ↗
3. Experimental assessment and simulation of surface nanocrystallization by severe shot peening10.1016/j.actamat.2015.06.054 ↗
4. Effects of Rayleigh damping, friction and rate-dependency on 3D residual stress simulation of angled shot peening10.1016/j.matdes.2012.09.030 ↗
5. Fatigue life improvement through surface nanostructuring of stainless steel by means of surface mechanical attrition treatment10.1016/j.scriptamat.2006.01.049 ↗
6. Enhancing the mechanical and biological performance of a metallic biomaterial for orthopedic applications through changes in the surface oxide layer by nanocrystalline surface modification10.1039/C5NR00574D ↗
7. Friction and wear behaviors of nanocrystalline surface layer of pure copper10.1016/j.wear.2005.06.010 ↗
8. Microstructure and corrosion resistance of modified 2024 Al alloy using surface mechanical attrition treatment combined with microarc oxidation process10.1016/j.corsci.2010.09.061 ↗
9. Role of grain size in the regulation of osteoblast response to Ti–25Nb–3Mo–3Zr–2Sn alloy10.1016/j.colsurfb.2013.06.007 ↗
10. The influence of nanostructured features on bacterial adhesion and bone cell functions on severely shot peened 316L stainless steel10.1016/j.biomaterials.2015.09.019 ↗
11. An investigation of surface nanocrystallization mechanism in Fe induced by surface mechanical attrition treatment10.1016/S1359-6454(02)00310-5 ↗
12. Formation of nanostructured surface layer on AISI 304 stainless steel by means of surface mechanical attrition treatment10.1016/S1359-6454(02)00594-3 ↗
13. Nanostructure formation mechanism of α-titanium using SMAT10.1016/j.actamat.2004.05.023 ↗
14. Chapter 14-continuous recrystallization during and after large strain deformation
15. New insights into the development of microstructure and deformation texture in nickel–60wt.% cobalt alloy10.1016/j.actamat.2014.06.031 ↗
16. Texture transition in cold-rolled nickel–40wt.% cobalt alloy10.1016/j.actamat.2014.03.066 ↗
17. Effects of Al addition on high strain rate deformation of fully austenitic high Mn steels10.1016/j.msea.2011.06.020 ↗
18. Formation of shear bands and strain-induced martensite during plastic deformation of metastable austenitic stainless steels10.1016/j.actamat.2007.07.015 ↗
19. Surface nanocrystallization of 316L stainless steel induced by ultrasonic shot peening10.1016/S0921-5093(00)00686-9 ↗
20. Cold rolling behaviour and textural evolution in AISI 316L austenitic stainless steel10.1016/j.actamat.2005.05.006 ↗
21. Tensile properties of a nanocrystalline 316L austenitic stainless steel10.1016/j.scriptamat.2005.01.023 ↗
22. Correlation between the microstructure studied by X-ray line profile analysis and the strength of high-pressure-torsion processed Nb and Ta10.1016/j.actamat.2012.10.008 ↗
23. Microstructural parameters from X-ray diffraction peak broadening10.1016/j.scriptamat.2004.05.007 ↗
24. The determination of density and distribution of dislocations in deformed single crystals from broadened X-ray diffraction profiles10.1002/pssa.19700020224 ↗
25. The effect of dislocation contrast on x-ray line profiles in untextured polycrystals10.1002/(SICI)1521-396X(199902)171:2<425::AID-PSSA425>3.0.CO;2-W ↗
26. Production and property evaluation of single crystal austenitic stainless steels10.2320/matertrans1989.41.806 ↗
27. The three-dimensional nature of microbands in a channel die compressed Goss-oriented Ni single crystal10.1016/j.scriptamat.2010.10.020 ↗
28. Development and persistence of microbands in copper deformed under complex strain paths10.1016/0956-716X(93)90478-B ↗
29. Evolution of microbands in high purity aluminium–3% magnesium during hot deformation testing in tension–compression10.1016/S1359-6462(01)00989-7 ↗
30. Deformation twinning in polycrystalline copper at room temperature and low strain rate10.1016/j.actamat.2005.10.002 ↗
31. Observations of common microstructural issues associated with dynamic deformation phenomena: twins, microbands, grain size effects, shear bands, and dynamic recrystallization10.1023/B:JMSC.0000013870.09241.c0 ↗
32. Microbands and microtwins associated with impact craters in copper and brass targets: the role of stacking fault energy10.1016/S1044-5803(03)00034-2 ↗
33. Effect of grain size and pressure on twinning and microbanding in oblique shock loading of copper rods10.1016/S1359-6454(97)00018-9 ↗
34. Microstructural characteristics of post-shear localization in cold-rolled 316L stainless steel10.1016/j.actamat.2006.09.001 ↗
35. The deformation of low-stacking-fault-energy austenitic steels10.1007/BF02700983 ↗
36. The role of deformation mechanisms in flow localization of 316L stainless steel10.1016/j.jnucmat.2006.05.047 ↗
37. Grain refinement in copper under large strain deformation10.1080/01418610108216659 ↗
38. The formation of microbands by cross-slips10.1016/0036-9748(83)90098-4 ↗
39. Microband formation in shock-loaded and quasi-statically deformed metals10.1016/0001-6160(89)90206-X ↗
40. Overview no. 96 evolution of fcc deformation structures in polyslip10.1016/0956-7151(92)90296-Q ↗
41. Development of adiabatic shear bands in annealed 316L stainless steel: Part I. Correlation between evolving microstructure and mechanical behavior10.1007/BF02586217 ↗
42. Deformation banding and shear banding in single crystals10.1016/j.actamat.2006.05.043 ↗
43. Crystallographic aspects of the early stages of recrystallisation in brass-type shear bands10.1016/S1359-6454(02)00266-5 ↗
44. Modelling oriented nucleation and selective growth during dynamic recrystallization10.1016/0956-716X(92)90147-7 ↗
45. Nanostructures in Ti processed by severe plastic deformation10.1557/JMR.2003.0267 ↗
46. Microstructure of ultrafine-grained fcc metals produced by severe plastic deformation10.1016/j.cap.2005.07.039 ↗
47. Hall–Petch relation and boundary strengthening10.1016/j.scriptamat.2004.06.002 ↗
48. Orientation-dependent evolution of the dislocation density in grain populations with different crystallographic orientations relative to the tensile axis in a polycrystalline aggregate of stainless steel10.1016/j.actamat.2013.11.012 ↗
49. The α-factor in the Taylor flow-stress law in monotonic, cyclic and quasi-stationary deformations: dependence on slip mode, dislocation arrangement and density10.1016/j.cossms.2016.07.001 ↗
50. A dislocation-based model for all hardening stages in large strain deformation10.1016/S1359-6454(98)00196-7 ↗
51. Dislocation wall and cell structures and long-range internal stresses in deformed metal crystals10.1016/0001-6160(83)90007-X ↗