Acceptance Criteria for Defects in Polyethylene Welds, Coupling Phased Array Ultrasonic Testing and Destructive Tests
Source abstract
Abstract
As a promising reference technique for non-destructive evaluation of both electrowelded and butt-fused polyethylene (PE) assemblies, Phased Array Ultrasonic Testing (PAUT) is still studied extensively in several laboratories worldwide and is supported by the technical standard ISO TS 16943. During the last 10 years, several joint projects have been completed aiming at evaluating the acuity of PAUT applied to both pipes and electrofused assemblies either exhumed from the field or prepared in laboratory. More recently, a focus has been made on fixing some acceptance criteria combining PAUT data and long term resistance of the laboratory joints. This paper presents the updated data obtained on electrofused assemblies—63 mm saddles and 110 mm sockets—containing different types of defects such as: insufficient heating time, pipe under-penetration in the socket, excessive localized scraping, pollutants and calibrated thin strips, in both mass and cross configuration, put at the interface pipe-saddle. PAUT scanning on the different specimens, both during the welding phase and after cooling, confirms the capability of the technique to visualize and size the Heat Affected Zone (HAZ), which can be revealed and compared afterwards on sample sections. Moreover, most of the defects are detected and sized, confirming the fairly good performance of PAUT, except for the smallest strips which are located in non accessible zones, due to the particular design of the saddle. Long term resistance of the welds is then evaluated by Hydrostatic Pressure Tests (HPT) followed by a decohesion test after rupture, according to the requirements of both the ISO 13956 and NF EN 1555 standards. Under such test conditions, every joints comply with the requirements of the standards (rupture time greater than 1000 h at 80 °C and 5 MPa), even those violating the critical proportions of non-welded zones.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Ultrasonics and Acoustic Wave Propagation
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (39)
Show source-provided references
1. Hwang, J.S., Shin, H.J., Song, S.J., Song, T.K.: 26th review of progress in quantitative non-destructive evaluation. In: Thompson, D.O., Chimenti, D.E. (eds.) AIP Conference Proceedings, vol. 19A, 509, pp. 1087–1093 (1999)
2. Troughton, M.: Welding with integrated non-destructive examination of PE pipes. Plastics Pipes XI, München (Germany), 3-6 September 2001
3. Shin, H.J., Kwon, J.-R., Song, S.-J.: Ultrasonic real time imaging technique for the inspection of electrofusion joints for polyethylene piping. In: Korea Gas Safety Corporation (ed.) 2001 Forum for Gas Safety, KGS 2001-069, p. 21, 27 September 2001
4. Ghia, S., Olivero, D., Piovano, M.: Italgas experience on non-destructive evaluation of PE pipe welding. In: Proceedings of the Plastic Pipes XII, Milan, Italy, 19–22 April 2004
5. Shin, H.J., Jang, Y.H., Kwon, J.R., Lee E.J.: Non-destructive testing of fusion joints of polyethylene piping by real time ultrasonic imaging. In: Plastics Pipes XII Conference, Milan, Italy, 19–22 April 2004
6. Bird, C., Caravaca, D., Raude, A.: Plastics pipes XIII, “The Inspection of Cold Welds in Electrofusion Joints”, session 7A, Washington DC, USA, 2-6t October 2006
7. Troughton, M., Brown, M., Hessel, J., Piovano, M.: Comparison of long-term and short-term tests for electrofusion joints in PE pipes. In: Proceedings of the Plastics Pipes XIII, Washington DC, USA, 2–5 October 2006
8. Gueugnaut, D., Garneret, G., Sèvre, B., Lopitaux, A.: Evaluation of the quality of the PE assemblies joined by electrofusion: analysis of the standardized tests designed to evaluate the cohesive resistance. In: 2008 International Gas Union Research Conference, Distribution Session N°199/E/S2, Cité des Sciences et de l’Industrie, Paris, France, 8–10 October 2008
9. Gueugnaut, D., Piovano, M., Garneret, G., Sèvre, B., Vacchina, M., Cantore C.: Evaluation of a new non-destructive technique of the polyethylene welded assemblies. In: 2008 International Gas Union Research Conference, Distribution Session N°196/E/S2, Cité des Sciences et de l’Industrie, Paris, France, 8–10 October 2008
10. Frederick, C.J.: Detection and quantification of detrimental conditions in HDPE using ultrasonic phased array. In: Proceedings of the Plastic Pipes XVI, Vancouver (BC), September 2010
11. Postma, P.J.: Suitable non-destructive testing techniques for polyethylene pipe joints. GERG PC Distribution Project n°GT-120214, October 2012
12. Postma P.: Plastic Pipes XVI, Barcelona, Spain, 24-26 September 2012
13. Troughton, M., Spicer, M., Hagglund, F.: Development of an automated phased array ultrasonic inspection system and flaw acceptance criteria for welded joints in polyethylene pipes. In: Proceedings of the Plastic Pipes XVI, Barcelona, Spain, 24-26 September 2012
14. Troughton, M., Jones, I., Andrews, S.: State of the art in welding thermoplastics and in assessing thermoplastic welded joints. Giornate Nazionali della Saldatura dei Materiali Plastici e Compositi, GNS7, Genoa (Italy), 23-24 May 2013
15. Troughton, M., Spicer, M., Hagglund, F.: Development and assessment of ultrasonic inspection system for polyethylene pipes. In: Proceedings of the ASME 2013 Pressure Vessels and Piping Conference, PVP2013, Paris, France, 14-18 July 2013
16. Hagglund, F., Robson, M., Troughton, M., Spicer, W., Pinson, I.: A novel phased array ultrasonic testing (PAUT) system for on-site inspection of welded joints in plastic pipes. In: 11th European Conference in Non-Destructive Testing (ECNDT), Prague, Czech Republic, October 2014
17. Troughton, M., Spicer, M., Hagglund, F.: Development and assessment of a phased array ultrasonic inspection system for polyethylene pipe joints. In: ANTEC 2014 Conference, Las Vegas, USA, April 2014
18. Seonghee, K., Jeongrock, K., Keebong, Y.: Proceedings of the 17th Plastic Pipes Conference, Chicago, Illinois, USA, 22-24 September 2014
19. Postma, P., Hermkens, R.: Suitability of non-destructive techniques for polyethylene pipe joints. A GERG investigation into the suitability of current techniques. Plastic Pipes XVII, Chicago, USA, 22-24 September 2014
20. ISO TC138/SC5 ISO/DTR16943: 2022. Thermoplastic pipes for the conveyance of fluids—inspection of polyethylene electrofusion socket joints using the phased array ultrasonic testing method
21. Gueugnaut, D., Boujlal, A., Sèvre, B., Angelini, F.: The capability of the ultrasonic phased array technique for detecting and measuring defects at the inner surface of a polyethylene pipe through an outside analysis. Plastic Pipes XVI, Barcelona, Spain, 24-26 September 2012
22. Gueugnaut, D., Boujlal, A., Bouaffre, R., Sèvre, B., Angelini, F., Louet, P.: Use of phased array technology for the inspection of polyethylene gas distribution pipes and fittings. In: European Symposium on Pressure Equipment ESOPE, Cité des Sciences de La Villette, Paris, 08-10 October 2013
23. Gueugnaut, D., Angelini, F., Boujlal, A., Bouaffre, R., Sèvre, B., Louet, P.: Ultrasonic phased array inspection of polyethylene pipelines & fittings used for gas distribution. Plastic Pipes XVII, Session 2B, Chicago, Illinois, USA, 22-24 September 2014
24. Gueugnaut, D., Angelini, F., Boujlal, A., Bouaffre, R., Sèvre, B., Louet, P.: 4th China International Plastic Pipe Conference, Shanghai, China, 21-22 September 2015
25. Gueugnaut, D., Tessier, M., Bouaffre, R., Lopitaux, A.: Ultrasonic phased array inspection of electrofused joints implemented in polyethylene gas piping systems. J. Mater. Sci. Eng. 7(2), 68–81 (2017)
26. ISO 13956: 2010. Plastics pipes and fittings—decohesion test of polyethylene (PE) saddle fusion joints—evaluation of ductility of fusion joint interface by tear test
27. ISO 13954: 1997. Plastics pipes and fittings—peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
28. ISO 13955: 1997. Plastics pipes and fittings—crushing decohesion test for polyethylene (PE) electrofusion assemblies
29. NF EN 1555-2: 2021. Plastics piping systems for the supply of gaseous fuels—polyethylene (PE)—part 2: pipes
30. NF EN 1555-3: 2021. Plastics piping systems for the supply of gaseous fuels—polyethylene (PE)—part 3: fittings
31. Troughton, M., Khamsehnzhad, A.: Development of flaw acceptance criteria for welded joints in PE pipes. ID25, p.71, NDT Workshop of Plastic Pipes XVIII, Berlin, Germany, 11-14 September 2016
32. Wermelinger, J., Hein, O.: Long term influence of defects in butt fusion joints on PE100 pipes and NDT detection of them. ID33, p.72, NDT Workshop of Plastic Pipes XVIII, Berlin, Germany, 11-14 September 2016
33. Gueugnaut, D., Bouaffre, R., Lopitaux, A., Renaud, R., Angelini, F., Louet, P.: Ultrasonic phased array evaluation of the integrity of polyethylene piping systems. In: 19th World Conference on Non-Destructive Testing, Münich (Germany), 13-17 June 2016
34. Gueugnaut, D., Angelini, F., Bouaffre, R., Tessier, M.: Ultrasonic phased array inspection of polyethylene damaged pipes with calibrated faults. ID96, p.67, NDT Workshop of Plastic Pipes XVIII, Berlin, Germany, 11-14 September 2016
35. Postma, P.: Determining acceptance criteria for non-destructive testing of electrofusion joints. ID181, p.73, NDT Workshop of Plastic Pipes XVIII, Berlin, Germany, 11-14 September 2016
36. Gueugnaut, D., Tessier, M., Bouaffre, R.: Acceptance criteria for volume defects in welded assemblies, detected and sized using the phased array ultrasonic technique. Plastic Pipes XIX, Session 4A, Las Vegas, NV, USA, 24-26 September 2018
37. Wermelinger, J., Choi, S.: Worldwide ISO Round Robin Study on phased array ultrasonic non-destructive test for electrofusion socket joints. In: Proceedings of the 20th Plastic Pipes Conference PPXX, Amsterdam, Netherlands, 6-8 September 2021
38. Gueugnaut, D., Wackernie, P., Forgerit, J.P.: Infrared microspectrometric study of the thermal history of fusion welding of polyethylene. J. Appl. Polym. Sci. 35, 1683 (1988)10.1002/app.1988.070350623 ↗
39. Berger, I.J., Frank, A., Pinter, G., Nitsche, D., Petry, D.: Investigation of the failure behavior of polyethylene electrofusion sockets. Plastic Pipes XIX, Session 4A, Las Vegas, NV, USA, 24-26 September 2018