Effect of heat treatment on corrosion properties of mixed sol gel silica–titania (7–3) coating
Source abstract
Abstract
Abstract In this paper, the sol–gel method has been used for preparing silica–titania coats with a molar ratio of 7:3 on TiNi that were heat treated at 300 °C and 500 °C. For studying and investigating the property of corrosion and microstructure of coats; SEM (scanning electron microscopy), EIS (electrochemical impedance spectroscopy), polarization dynamic and roughness measurement have been used and XRD (X-ray diffraction) has been also used for characterizing the coats. Heat treatment at 500 °C caused the increase of porosity and coating cracking that finally caused the decrease of corrosion resistance. The best corrosion resistance was achieved for the sample that was heat treated at 300 °C. The structure of the heat treated sample at 300 °C was amorphous and the increase of temperature of heat treatment from 300 °C to 500 °C caused crystallization and decrease of the corrosion resistance. Crystallization affected both corrosion resistance and surface roughness.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Silicone and Siloxane Chemistry · Gas Sensing Nanomaterials and Sensors · Analytical Chemistry and Sensors
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (16)
Show source-provided references
1. Evaluation of TiO2 coatings obtained using the sol–gel technique on surgical grade type 316L stainless steel in simulated body fluid10.1016/j.matlet.2005.05.036 ↗
2. Multilayer silicamethacrylate hybrid coatings prepared by sol–gel on stainless steel 316L: electrochemical evaluation10.1016/j.surfcoat.2007.09.007 ↗
3. Preparation and characterization of sol–gel bioactive glass coating for improvement of biocompatibility of human body implant10.1016/j.msea.2007.05.041 ↗
4. Structural characterization and properties of the TiO2 film on tinplate10.1016/j.jallcom.2007.10.093 ↗
5. Effect of sintering temperatures on corrosion and wear properties of sol–gel alumina coatings on surface pre-treated mild steel10.1016/j.corsci.2007.10.002 ↗
6. Study on a hydrophobic nano-TiO2 coating and its properties for corrosion protection of metals10.1016/j.electacta.2005.04.048 ↗
7. Mixed SiO2–TiO2 (1:1) sol–gel films on mild steel substrates: sol composition and thermal treatment effects10.1016/j.surfcoat.2007.08.070 ↗
8. A study on the N-, S- and Cl-modified nano-TiO2 coatings for corrosion protection of stainless steel10.1016/j.electacta.2007.04.078 ↗
9. Natural and persistent superhydrophilicity of SiO2/TiO2 and TiO2/SiO2 bi- layer films10.1016/j.tsf.2007.06.005 ↗
10. Electrochemical behaviour enhancement of stainless steels by a SiO2 PACVD coating10.1016/j.corsci.2008.01.015 ↗
11. Development and bio-electrochemical characterization of a novel TiO2–SiO2 mixed oxide coating for titanium implants10.1007/s10856-008-3409-2 ↗
12. Study on the superhydrophilicity of the SiO2–TiO2 thin films prepared by sol–gel method at room temperature10.1023/B:JSST.0000023851.36715.b5 ↗
13. Sol–gel-derived TiO2–SiO2 implant coatings for direct tissue attachment. Part II: evaluation of cell response10.1007/s10856-007-3064-z ↗
14. Influence of solvent concentration on the microstructure of SiO2–TiO2 sol–gel films
15. Effect of nanosilica type on protective properties of composite ceramic coatings deposited on steel 316L by sol–gel technique10.1016/j.jnoncrysol.2007.08.056 ↗
16. Characterisation of interactive TiO2//SiO2 coatings by complementary techniques10.1016/S0040-6090(99)00212-6 ↗