Conductive plastics: comparing alternative nanotechnologies by performance and life cycle release probability
Source abstract
Abstract
Nanocomposites can be considered safe during their life cycle as long as the nanofillers remain embedded in the matrix. Therefore, a possible release of nanofillers has to be assessed before commercialization. This report addresses possible life cycle release scenarios for carbon nanotubes (CNT), graphene, and carbon black (CB) from a thermoplastic polyurethane (TPU) matrix. The content of each nanofiller was adjusted to achieve the same conductivity level. The nanofillers reduced the rate of nanoscale releases during mechanical processing with decreasing release in the order neat TPU, TPU-CNT, TPU-graphene, and TPU-CB. Released fragments were dominated by the polymer matrix with embedded or surface-protruding nanofillers. During electron microscopy analysis, free CB was observed, however, there was no free CNT or graphene. Quantitatively, the presence of free nanofillers remained below the detection limit of <0.01% of generated dust. Further, both the production process and type of mechanical processing showed a significant impact with higher release rates for injection-molded compared to extruded and sanded compared to drilled materials. Due to its optimal performance for further development, extruded TPU-CNT was investigated in a combined, stepwise worst case scenario (mechanical processing after weathering). After weathering by simulated sunlight and rain, CNT were visible at the surface of the nanocomposite; after additional sanding, fragments showed protruding CNT, but free CNT were not detected. In summary, this preliminary exposure assessment showed no indication that recommended occupational exposure limits for carbonaceous nanomaterials can be exceeded during the life cycle of the specific TPU nanocomposites and conditions investigated in this study.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microplastics and Plastic Pollution · Recycling and Waste Management Techniques · Nanoparticles: synthesis and applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. Asbach C, Kaminski H, von Barany D, Kuhlbusch TAJ, Monz C, Dziurowitz N, Pelzer J, Vossen K, Berlin K, Dietrich S, Goetz U, Kiesling H-J, Schierl R, Dahmann D (2012) Comparability of portable nanoparticle exposure monitors. Ann Occ Hyg 56(5):606–621
2. Bauhofer W, Kovacz JZ (2009) A review and analysis of electrical percolation in carbon nanotube polymer composites. Compos Sci Technol 69:1486–149810.1016/j.compscitech.2008.06.018 ↗
3. Bello D, Wardle BL, Zhang J, Yamamoto N, Santeufemio C, Hallock M, Virji MA (2010) Characterization of exposures to nanoscale particles and fibers during solid core drilling of hybrid carbon nanotube advanced composites. Int J Occup Environ Health 16:434–45010.1179/oeh.2010.16.4.434 ↗
4. Buxbaum G, Pfaff G (2006) Industrial inorganic pigments. Wiley-VCH, Weinheim
5. Cruz SM, Viana JC (2015) Melt blending and characterization of carbon nanoparticles filed thermoplastic polyurethane elastomers. J Elastomers Plas 47:647–66510.1177/0095244314534097 ↗
6. Ding Y, Wohlleben W, Boland M, Vilsmeier K, Riediker M (2016) Nano-object release during machining of polymer-based nanocomposites depends on process factors and the type of nanofiller. Env Health Persp (submitted)10.1093/annweh/wxx081 ↗
7. Duncan TV (2015) Release of engineered nanomaterials from polymer nanocomposites: the effect of matrix degradation. ACS Appl Mater Interfaces 7:20–3910.1021/am5062757 ↗
8. Froggett SJ, Clancy SF, Boverhof DR, Canady RA (2014) A review and perspective of existing research on the release of nanomaterials from solid nanocomposites. Part Fibre Toxicol 11:1710.1186/1743-8977-11-17 ↗
9. Ging J, Tejerina-Anton R, Ramakrishnan G, Nielsen M, Murphy K, Gorham JM, Nguyen T, Orlov A (2014) Development of a conceptual framework for evaluation of nanomaterials release from nanocomposites: environmental and toxicological implications. Sci Total Environ 473–474:9–1910.1016/j.scitotenv.2013.11.135 ↗
10. Goehler D, Nogowski A, Fiala P, Stintz M (2013) Nanoparticle release from nanocomposites due to mechanical treatment at two stages of the life-cycle. J Physics:Conf Series 429:012045
11. Harper S, Wohlleben W, Doa M, Nowack B, Clancy S, Canady R, Maynard A (2015) Measuring nanomaterial release from carbon nanotube composites: review of the state of the science. J Phys Conf Ser 617:01202610.1088/1742-6596/617/1/012026 ↗
12. Hirth S, Cena L, Cox G, Tomović Ž, Peters T, Wohlleben W (2013) Scenarios and methods that induce protruding or released CNTs after degradation of nanocomposite materials. J Nanopart Res 15:150410.1007/s11051-013-1504-x ↗
13. Huang G, Park JH, Cena LG, Shelton BL, Peters TM (2012) Evaluation of airborne particle emissions from commercial products containing carbon nanotubes. J Nanopart Res 14:123110.1007/s11051-012-1231-8 ↗
14. Khan U, May P, O’Neill A, Vilatela JJ, Windle AH, Coleman JA (2011) Tuning the mechanical properties of composites from elastomeric to rigid thermoplastic by controlled addition of carbon nanotubes. Small 7:1579–158610.1002/smll.201001959 ↗
15. Kim H, Abdala AA, Macosko CW (2010a) Graphene/polymer nanocomposites. Macromolecules 43:6515–653010.1021/ma100572e ↗
16. Kim H, Miura Y, Macosko CW (2010b) Graphene/polyurethane nanocomposites for improved gas barrier and electrical conductivity. Chem Mater 22:3441–345010.1021/cm100477v ↗
17. Kingston C, Zepp R, Andrady A, Boverhof D, Fehir R, Hawkins D, Roberts J, Sayre P, Shelton B, Sultan Y, Vejins V, Wohlleben W (2014) Release characteristics of selected carbon nanotube polymer composites. Carbon 68:33–5710.1016/j.carbon.2013.11.042 ↗
18. Le Bihan O, Shandilya N, Gheerardyn L, Guillon O, Dore E, Morgeneyer M (2013) Investigation of the release of particles from a nanocoated product. Advances in Nanoparticles 2:39–4410.4236/anp.2013.21008 ↗
19. Lv Y, Huang Y, Yang J, Kong M, Yang H, Zhao J, Li G (2015) Outdoor and accelerated laboratory weathering of polypropylene: a comparison and correlation study. Polym Degrad Stabil 112:145–15910.1016/j.polymdegradstab.2014.12.023 ↗
20. Ma-Hock L, Strauss V, Treumann S, Kuttler K, Wohlleben W, Hofmann T, Groters S, Wiench K, van Ravenzwaay B, Landsiedel R (2013) Comparative inhalation toxicity of multi-wall carbon nanotubes, graphene, graphite nanoplatelets and low surface carbon black. Part Fib Tox 10:2310.1186/1743-8977-10-23 ↗
21. Ministère de l'Environnement, de l'Énergie et de la Mer, Éléments issus des déclarations des substances à l’état nanoparticulaire: Rapport d’Étude 2015
22. Nguyen TL, Wohlleben W, Sung L (2014) Mechanisms of aging and release from weathered nanocomposites. In: Wohlleben W, Kuhlbusch T, Schnekenburger J, Lehr CM (eds) Safety of nanomaterials along their lifecycle: release, exposure, and human hazards. CRC Press, Boca Raton, pp 315–33410.1201/b17774-18 ↗
23. Nowack B, David RM, Fissan H, Morris H, Shatkin JA, Stintz M, Zepp R, Brouwer D (2013) Potential release scenarios for carbon nanotubes used in composites. Environ Int 59:1–1110.1016/j.envint.2013.04.003 ↗
24. OECD (2016) Strategies, techniques and sampling protocols for determining the concentrations of manufactured nanomaterials in air, ENV/CHEM/NANO (2016)23
25. Pantea D, Darmstadt H, Kaliaguine S, Roy C (2003) Electrical conductivity of conductive carbon blacks: influence of surface chemistry and topology. Appl Surf Sci 217:181–19310.1016/S0169-4332(03)00550-6 ↗
26. Poetschke P, Haussler L, Pegel S, Steinberger R, Scholz G (2007) Thermoplastic polyurethane filled with carbon nanotubes for electrical dissipative and conductive applications. KGK Kautschuk, Gummi, Kunststoffe 60(9):432–437
27. Randal D, Lee S (2002) The polyurethane book. John Wiley & Sons, New York
28. Saber AT, Koponen IK, Jensen KA, Jacobsen NR, Mikkelsen L, Møller P, Loft S, Vogel U, Wallin H (2012a) Inflammatory and genotoxic effects of sanding dust generated from nanoparticle-containing paints and lacquers. Nanotoxicology 6:776–78810.3109/17435390.2011.620745 ↗
29. Saber AT, Jensen KA, Jacobsen NR, Birkedal R, Mikkelsen L, Møller P, Loft S, Wallin H, Vogel U (2012b) Inflammatory and genotoxic effects of nanoparticles designed for inclusion in paints and lacquers. Nanotoxicology 6:453–47110.3109/17435390.2011.587900 ↗
30. Schlagenhauf L, Nüesch F, Wang J (2014) Release of carbon nanotubes from polymer nanocomposites. Fibers 2:108–12710.3390/fib2020108 ↗
31. Schlagenhauf L, Buerki-Thurnherr T, Kuo Y-Y, Wichser A, Nüesch F, Wick P, Wang J (2015) Carbon nanotubes released from an epoxy-based nanocomposite: quantification and particle toxicity. Environ Sci Technol 49:10616–1062310.1021/acs.est.5b02750 ↗
32. Smulders S, Luyts K, Brabants G, Van Landuyt K, Kirschhock C, Smolders E, Golanski L, Vanoirbeek J, Hoet PHM (2014) Toxicity of nanoparticles embedded in paints compared with pristine nanoparticles in mice. Toxicol Sci 141:132–14010.1093/toxsci/kfu112 ↗
33. Walter J, Löhr K, Karabudak E, Reis W, Mikhael J, Peukert W, Wohlleben W, Cölfen H (2014) Multidimensional analysis of nanoparticles with highly disperse properties using multiwavelength analytical ultracentrifugation. ACS Nano 8(9):8871–888610.1021/nn503205k ↗
34. Wohlleben W (2012) Validity range of centrifuges for the regulation of nanomaterials: from classification to as-tested coronas. J Nanopart Res 14:130010.1007/s11051-012-1300-z ↗
35. Wohlleben W, Brill S, Meier M, Mertler M, Cox G, Hirth S, von Vacano B, Strauss V, Treumann S, Wiench K, Ma-Hock L, Landsiedel R (2011) On the lifecycle of nanocomposites: comparing released fragments and their in-vivo hazards from three release mechanisms and four nanocomposites. Small 7:2384–239510.1002/smll.201002054 ↗
36. Wohlleben W, Meier MW, Vogel S, Landsiedel R, Cox G, Hirth S, Tomović Ž (2013) Elastic CNT-polyurethane nanocomposite: synthesis, performance and assessment of fragments released during use. Nanoscale 5:369–38010.1039/C2NR32711B ↗
37. Wohlleben W, Kingston C, Carter J, Sahle-Demessie E, Vázquez-Campos S, Acrey B, Chen C-Y, Walton E, Egenolf H, Müller P, Zepp R (2017) Nano release: pilot interlaboratory comparison of a weathering protocol applied to resilient and labile polymers with and without embedded carbon nanotubes. Carbon 113:346–36010.1016/j.carbon.2016.11.011 ↗