Features of the Application of Coatings Based on the ZrN System to Increase Resistance to Mechanical Wear and Corrosion of Titanium Alloy Products
Source abstract
Abstract
The coatings of ZrN, (Zr,Ti)N, (Ti,Zr,Hf)N and (Ti,Zr,Nb)N deposited on the titanium alloy substrate were compared. The wear resistance in the pin-on-disk test together with the Al2O3 indenter and the corrosion resistance in 3.5% NaCl solution were studied. It was found that the (Zr,Nb,Ti)N coating has the best resistance to wear, but has low corrosion resistance. The (Ti,Zr,Hf)N coating, on the contrary, has the best corrosion resistance, but low resistance to wear. The ZrN coating has good corrosion resistance combined with good resistance to wear. This coating is best suited for use in friction conditions with a ceramic counterbody under the influence of seawater. An important resource for increasing the properties of coatings is increasing their adhesion to the substrate, which can be achieved in two combined ways: (1) complete removal of the original oxide layer from the surface of the substrate and (2) the use of optimal compositions of the adhesive sublayer, which have not only high adhesive properties in relation to both the substrate and the coating, but also high strength. While the introduction of Nb into the ZrN coating composition increases wear resistance and the introduction of Hf increases corrosion resistance, the ZrN coating without additives best resists wear and corrosion simultaneously.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Advanced materials and composites · Titanium Alloys Microstructure and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of High-Efficiency Machining Technologies, Moscow State University of Technology “STANKIN”, Vadkovsky Lane 3a, 127055 Moscow, Russia
Department of Chemistry, Technology of Electrochemical Production and Electronic Engineering Materials, Chemical Technology and Engineering Faculty, Belarusian State Technological University, 13a, Sverdlov Street, 220006 Minsk, Belarus
Materials Science and Metallurgy Shared Use Research and Development Center, National University of Science and Technology “MISiS”, Leninsky Prospect 4, 119049 Moscow, Russia
Department of Materials Science, Moscow Polytechnic University, Bolshaya Semyonovskaya Street, 38, 107023 Moscow, Russia
Institute of Design and Technological Informatics of the Russian Academy of Sciences (IDTI RAS), Vadkovsky Lane 18a, 127055 Moscow, Russia
Funding
Ministry of Science and Higher Education of the Russian Federation
References (85)
Show source-provided references
1. Metallic implant biomaterials10.1016/j.mser.2014.10.001 ↗
2. Review on titanium and titanium based alloys as biomaterials for orthopaedic applications10.1016/j.msec.2019.04.064 ↗
3. Design, processing, microstructure, properties, and applications of advanced intermetallic TiAl alloys10.1002/adem.201200231 ↗
4. Chapter 13 The study of the adhesion of a TiN coating on steel and titanium alloy substrates using a multi-mode scratch tester10.1016/S0167-8922(06)80049-0 ↗
5. Study of the tribological performance of zirconia-based materials in pair with VT-9 titanium alloy10.3103/S106836661202002X ↗
6. Tribological Behavior of Titanium Alloys during Friction Against Ceramics10.4028/p-09k64f ↗
7. Friction and Wear Behavior of Paired Pairs of Ceramics and Metal in High-Pressure Pump of Seawater Desalination10.1007/s11223-021-00345-4 ↗
8. Micro-scale abrasive wear behavior of medical implant material Ti-25Nb-3Mo-3Zr-2Sn alloy on various friction pairs10.1016/j.msec.2014.05.039 ↗
9. Zhang, J., Wang, Z., Chen, W., Liao, H., Zeng, M., and Ma, S. (2019). Wear in silicon nitride sliding against titanium alloy pairs at different loads under artificial seawater lubrication. Front. Mater., 6.10.3389/fmats.2019.00155 ↗
10. Investigation of tribological properties of silicon nitride ceramic composites sliding against titanium alloy under artificial seawater lubricating condition10.1016/j.ijrmhm.2018.06.011 ↗
11. Online measurement of the elastic recovery value of machined surface in milling titanium alloy10.1007/s00170-022-09293-y ↗
12. Titanium nitride/vanadium nitride alloy coatings: Mechanical properties and adhesion characteristics10.1016/j.surfcoat.2004.09.008 ↗
13. Effects of plasma nitriding and multiple arc ion plating TiN coating on bacterial adhesion of commercial pure titanium via in vitro investigations10.1016/j.surfcoat.2012.07.046 ↗
14. CAE-PVD synthesis and characterization of titanium-based biocompatible coatings deposited on titanium alloy for biomedical application10.1016/j.matpr.2021.04.247 ↗
15. Effect of adhesion and the wear-resistant layer thickness ratio on mechanical and performance properties of ZrN-(Zr,Al,Si)N coatings10.1016/j.surfcoat.2018.09.087 ↗
16. Effect of Ti6Al4V Substrate Manufacturing Technology on the Properties of PVD Nitride Coatings10.12693/APhysPolA.142.723 ↗
17. Microstructure, mechanical properties and tribological performance of TiSiN-WS2 hard-lubricant coatings10.1016/j.apsusc.2014.05.012 ↗
18. Tantalum Coatings Deposited on Ti6Al4V Alloy by Self-Designed Wire Electrical Explosion Spraying10.1007/s11666-022-01333-z ↗
19. Review of titanium surface modification techniques and coatings for antibacterial applications10.1016/j.actbio.2018.10.036 ↗
20. The influence of metallic interlayers on the adhesion of PVD TiN coatings on high-speed steel10.1016/j.wear.2006.11.053 ↗
21. Mono- and multiple TiN(/Ti) coating adhesion mechanism on a Ti-13Nb-13Zr alloy10.1016/j.apsusc.2015.07.126 ↗
22. Pre- and post-surface treatments using electron beam technology for load-related application of thermochemical and PVD hard coatings on soft substrate materials10.1016/j.surfcoat.2019.07.084 ↗
23. Adhesion strength of tin coatings at various ion etching deposited on tool steels using cathodic ARC PVD technique10.1142/S0218625X09012251 ↗
24. Study of macrodroplet and growth mechanisms with and without ion etchings on the properties of TiN coatings deposited on HSS using cathodic arc physical vapour deposition technique10.1016/j.msea.2007.04.030 ↗
25. Structure and properties of TiBx coatings deposited via magnetron sputtering with ion source etching10.1016/j.ceramint.2021.02.175 ↗
26. Study on the adhesion and tribological behavior of PVD TiAlN coatings with a multi-scale textured substrate surface10.1016/j.ijrmhm.2018.01.003 ↗
27. Controllable preparation of micro-textures on WC/Co substrate surface by an integrated laser-dry etching process for improving PVD coatings adhesion10.1016/j.apsusc.2020.147580 ↗
28. Preparation of micro-textures on cemented carbide substrate surface by plasma-assisted laser machining to enhance the PVD tool coatings adhesion10.1016/j.jmatprotec.2020.116870 ↗
29. Adhesion and machining performance of PVD AlCrN coatings with an ion beam/laser textured substrate10.1016/j.surfcoat.2021.127607 ↗
30. Lapping and polishing of additively manufactured 316L substrates and their effects on the microstructural evolution and adhesion of PVD CrAlN coatings10.1016/j.surfcoat.2021.127905 ↗
31. Modeling study of adhesion in the TiN/Ti, TiN/ZrN, TiN/Ti/ZrN, and TiN/Zr/ZrN layered systems10.1080/00218464.2018.1488217 ↗
32. Cohesive failure and film adhesion of PVD coating: Cemented carbide substrate phase effect and its micro-mechanism10.1016/j.ijrmhm.2022.106066 ↗
33. Improved adhesion of cathodic arc PVD AlCrSiN coating on ion-implanted WC-Co substrates10.1016/j.ijrmhm.2023.106187 ↗
34. Scratch and indentation adhesion characteristics of multilayered PVD coatings before and after the heat treatment deposited by duplex process10.1088/2051-672X/ab4bb0 ↗
35. Influence of Ti-TiN multilayer PVD-coatings design on residual stresses and adhesion10.1016/j.matdes.2015.03.007 ↗
36. Modelling, production and characterisation of duplex coatings (HVOF and PVD) on Ti-6Al-4V substrate for specific mechanical applications10.1016/j.surfcoat.2007.02.041 ↗
37. Erosive wear behavior of Ti/Ti(V,Zr)N multilayered PVD coatings for Ti-6Al-4V alloy10.1016/j.wear.2018.11.016 ↗
38. Influence of tribological properties of Zr-ZrN-(Zr,Cr,Al)N and Zr-ZrN-(Zr,Mo,Al)N multilayer nanostructured coatings on the cutting properties of coated tools during dry turning of Inconel 718 alloy10.1016/j.wear.2022.204521 ↗
39. Effect of inserting the Zr layers on the tribo-corrosion behavior of Zr/ZrN multilayer coatings on titanium alloys10.1016/j.corsci.2023.111002 ↗
40. Improving the mechanical and tribological properties of amorphous carbon-based films by an a-C/Zr/ZrN multilayered interlayer10.1016/j.ceramint.2018.12.193 ↗
41. Properties of a composite multilayered hard coating Zr–ZrN10.3103/S1063457617050070 ↗
42. Effect of volume fraction on mechanical properties of Zr/ZrN multilayer systems10.1016/j.ceramint.2016.09.025 ↗
43. Influence of etching-pretreatment on nano-grained WC-Co surfaces and properties of PVD/HVOF duplex coatings10.1016/j.surfcoat.2019.05.054 ↗
44. Crack formation and oxidation wear in (Cr,Y,Al)N and (Mo,Y,Al)N nanolayer coatings with high content of yttrium10.1016/j.wear.2023.204989 ↗
45. The effect of a DLC coating adhesion layer on the corrosion behavior of titanium and the Ti6Al4V alloy for dental implants10.1016/j.surfcoat.2012.05.089 ↗
46. Interface stability and microstructure of ultrathin Mo/MoN diffusion barrier in Cu interconnects10.1179/1432891713Z.000000000184 ↗
47. Ultrathin Mo/MoN bilayer nanostructure for diffusion barrier application of advanced Cu metallization10.1016/j.apsusc.2010.03.109 ↗
48. Cyclic oxidation behavior and oxide scale adhesion of Al/NiCrAlY coating on pure titanium alloy10.1016/j.jallcom.2017.09.199 ↗
49. Adhesion improvement of diamond coatings on cemented carbide with high cobalt content using PVD interlayer10.1016/j.diamond.2013.01.012 ↗
50. Influence of the tribological properties of the Zr,Hf-(Zr,Hf)N-(Zr,Me,Hf,Al)N coatings (where Me is Mo, Ti, or Cr) with a nanostructured wear-resistant layer on their wear pattern during turning of steel10.1016/j.wear.2023.204624 ↗
51. Comparison of properties of ZrHf-(Zr,Hf)N-(Zr,Hf,Cr,Mo,Al)N and Ti-TiN-(Ti,Cr,Al)N nanostructured multilayer coatings and cutting properties of tools with these coatings during turning of nickel alloy10.1016/j.jmapro.2023.01.037 ↗
52. Investigation of the properties of the Cr,Mo-(Cr,Mo,Zr,Nb)N-(Cr,Mo,Zr,Nb,Al)N multilayer composite multicomponent coating with nanostructured wear-resistant layer10.1016/j.wear.2020.203597 ↗
53. Zirconium-based nanostructured coating on the Mg-4Y-3Re alloy for corrosion retardation10.1016/j.cplett.2020.137824 ↗
54. Wettability and corrosion of [NTf2] anion-based ionic liquids on steel and PVD (TiN, CrN, ZrN) coatings10.1016/j.surfcoat.2016.05.051 ↗
55. Improved corrosion resistance of Mg-Y-RE alloy coated with niobium nitride10.1016/j.tsf.2014.07.057 ↗
56. Corrosion behavior of ZrN/Zr coated biomedical AZ91 magnesium alloy10.1016/j.surfcoat.2009.02.074 ↗
57. Surface performances of PVD ZrN coatings in biological environments10.1080/17515831.2018.1553820 ↗
58. Influence of niobium and hafnium doping on the wear and corrosion resistance of coatings based on ZrN10.1016/j.jmrt.2023.11.086 ↗
59. (2020). Standard Test Methods for Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride Solution. Book of Standards Volume: 03.02, Last Updated: 11 December 2020 (Standard No. ASTM G48-11e1).
60. Tao, H., Zhylinki, V., Vereschaka, A., Chayeuski, V., Yuanming, H., Milovich, F., Sotova, C., Seleznev, A., and Salychits, O. (2023). Comparison of the Mechanical Properties and Corrosion Resistance of the Cr-CrN, Ti-TiN, Zr-ZrN, and Mo-MoN Coatings. Coatings, 13.10.3390/coatings13040750 ↗
61. Adhesion measurement of zirconium nitride and amorphous silicon carbide coatings to nickel and titanium alloys10.1016/S0257-8972(99)00042-0 ↗
62. In-vitro corrosion and surface properties of PVD-coated β-type TNTZ alloys for potential usage as biomaterials: Investigating the hardness, adhesion, and antibacterial properties of TiN, ZrN, and CrN film10.1016/j.surfcoat.2023.129624 ↗
63. Adhesion and mechanical properties of layered nano films TiN/ZrN and TiN/Ti/ZrN: Pseudopotential simulation10.1080/09276440.2018.1474665 ↗
64. A functionally graded coating from ZrN to Ti: Experimental characterization, erosion behavior and design concept10.1016/j.surfcoat.2022.128093 ↗
65. ZrN and ta-C coatings on titanium for biomedical applications: Improved adhesion, corrosion, antibacterial activity, and cytotoxicity properties10.1557/s43578-023-01109-3 ↗
66. Influence of substrate pre-treatments on residual stresses and tribo-mechanical properties of TiAlN-based PVD coatings10.1016/j.surfcoat.2014.08.075 ↗
67. DLC-coating application to improve the durability of ceramic tools10.1007/s11665-019-04149-1 ↗
68. Grigoriev, S.N., Volosova, M.A., Fedorov, S.V., Okunkova, A.A., Pivkin, P.M., Peretyagin, P.Y., and Ershov, A. (2021). Development of DLC-Coated Solid SiAlON/TiN Ceramic End Mills for Nickel Alloy Machining: Problems and Prospects. Coatings, 11.10.3390/coatings11050532 ↗
69. Investigation of the tribological properties of Ti-TiN-(Ti,Al,Nb,Zr)N composite coating and its efficiency in increasing wear resistance of metal cutting tools10.1016/j.triboint.2021.107236 ↗
70. Investigation of the influence of the features of the deposition process on the structural features of microparticles in PVD coatings10.1016/j.vacuum.2022.111144 ↗
71. Influence of the yttrium cathode arc current on the yttrium content in the (Ti,Y,Al)N coating and the coating properties10.1016/j.vacuum.2024.113028 ↗
72. Ward, L., Pilkington, A., and Dowey, S. (2017). Studies on the effect of arc current mode and substrate rotation configuration on the structure and corrosion behavior of PVD TiN coatings. Coatings, 7.10.3390/coatings7040050 ↗
73. Optimization of arc-PVD TiN coating process parameters by Taguchi technique10.1080/08982119908962554 ↗
74. Comparison of the wear and corrosion behavior between CrN and AlCrN coatings deposited by Arc-PVD method10.1088/2053-1591/ab4645 ↗
75. Muhammed, M., Javidani, M., Ebrahimi Sadrabadi, T., Heidari, M., Levasseur, T., and Jahazi, M. (2024). A Comprehensive Review of Cathodic Arc Evaporation Physical Vapour Deposition (CAE-PVD) Coatings for Enhanced Tribological Performance. Coatings, 14.10.3390/coatings14030246 ↗
76. (2000). Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus (G 99–95a) (Standard No. ASTM G99-95a(2000)e1).
77. Tensile properties of binary titanium-zirconium and titanium-hafnium alloys10.1016/0022-5088(62)90068-1 ↗
78. Features of microstructure, deformation and fracture of bioinert alloys based on zirconium and titanium-niobium in various structural states
79. Measurement and modeling of second phase precipitation kinetics in zirconium niobium alloys10.1520/JAI103011 ↗
80. Modelling precipitation in zirconium niobium alloys10.1016/j.jnucmat.2008.03.016 ↗
81. Nesterova, N.V., Osipov, S.Y., Orlov, V.K., and Petrov, D.D. (2018). High-Temperature Hafnium-Containing Alloy Based on Titanium. (2 675 063 C1), Patent RU.
82. Development of hafnium metal and titanium-hafnium alloys having apatite-forming ability by chemical surface modification10.1002/jbm.b.34068 ↗
83. Development of Nickel-Rich Nickel–Titanium–Hafnium Alloys for Tribological Applications10.1007/s40830-020-00296-w ↗
84. Zirconium-niobium alloys for core elements of pressurized water reactors10.1023/A:1027388503837 ↗
85. The effect of the Nb concentration on the corrosion resistance of nitrogen-containing multicomponent TiZrTaNb-based films in acidic environments10.1016/j.jallcom.2022.167005 ↗