journal article·2017-09

Continuous electron beam melting technology of silicon powder by prefabricating a molten silicon pool

Tong Lu, Yi Tan, Shuang Shi, Xiaoliang Guo, Jiayan Li, Dengke Wang

Vacuum· Volume 143
Publisher page

Abstract

Abstract We successfully achieved the continuous melting of silicon powder in a vacuum electron beam melting system. The characteristic of electron beam melting of silicon powder was revealed by comparing the three different approaches to prefabricate the molten silicon pool. The application of silicon block can be regarded as the most efficient method to prefabricate a stable molten silicon pool. Afterward, the silicon powder was added into the molten silicon pool at different rates by a spiral silicon powder feeding device. Finally, all of the silicon powder was melted completely. Although the P removal efficiency decreases with increasing powder feeding rate during the powder feeding process, an appropriate increase in the powder feeding rate is not only beneficial to improve the melting efficiency of silicon powder but also conductive to the improvement in uniformity of the obtained silicon ingot. Therefore, the powder feeding rate of 10 g/min was the best option in this study. Compared with the melting of silicon block, which has been wildly applied, this continuous powder feeding process can be beneficial to saving smelting time and the total cost.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Silicon and Solar Cell Technologies · Silicon Nanostructures and Photoluminescence · Thin-Film Transistor Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (17)

Show source-provided references
1. Modeling of poly-crystalline silicon ingot crystallization during casting and theoretical suggestion for ingot quality improvement10.1016/j.mssp.2016.05.013 ↗
2. Three-dimensional analysis of dislocation multiplication in single-crystal silicon under accurate control of cooling history of temperature10.1016/j.jcrysgro.2014.03.034 ↗
3. A study of purification process during the elaboration by electron bombardment of polysiliocn ribbons designed for photovoltaic conversion10.1016/0165-1633(81)90076-9 ↗
4. Impurities evaporation from metallurgical- grade silicon in electron beam melting process10.1007/s12598-011-0382-6 ↗
5. Removal of oxygen from silicon by electron beam melting10.1007/s00339-014-8367-6 ↗
6. Determination of the effective distribution coefficient (K) for silicon impurities
7. Removal of aluminum from metallurgical grade silicon using electron beam melting10.1016/j.vacuum.2011.09.018 ↗
8. Progress in research and development of solar-grade silicon preparation by electron beam melting10.15541/jim20140664 ↗
9. The purification of metallurgical grade silicon by electron beam melting10.1016/j.jmatprotec.2004.03.035 ↗
10. Profile of impurities in polycrystalline silicon samples purified in an electron beam melting furnace10.1016/S0927-0248(02)00471-3 ↗
11. Applications of Si nanoparticles in photovoltaic solar cells sili-con nanocrystals
12. Use of a plasma process to recycle silicon kerf loss to solar-grade silicon feedstock10.1016/j.seppur.2016.02.005 ↗
13. Beneficial and technological analysis for the recycling of solar grade silicon wastes10.1007/s11837-011-0006-5 ↗
14. Elimination of carbon contamination from silicon kerf using a furnace aerosol reactor methodology10.1021/acs.iecr.5b00577 ↗
15. Fabrication of Si nanoparticles from Si swarf and application to solar cells10.1016/j.apsusc.2014.02.131 ↗
16. Evaporation and removal mechanism of phosphorus from the surface of silicon melt during electron beam melting10.1016/j.apsusc.2012.12.022 ↗
17. Numerical simulation for parameter optimization of silicon purification by electron beam melting10.1016/j.vacuum.2013.02.002 ↗