Nanoindentation and isothermal compression behaviour of Al–4Cu–Ni composites
Source abstract
Abstract
The present investigation explores the nanoindentation and isothermal compression behaviour of Al–4Cu-xNi (x = 2, 4, 6, 8 and 10 wt%) Aluminium matrix composites produced by pressureless sintering technique. The scanning electron microscope (SEM) and X-ray diffraction (XRD) analyses of sintered samples reveal the presence of core-shell type Al3Ni and Al3Ni2 intermetallic formation at the interface between Ni particulates and the Al–Cu matrix. Nanoindentation study shows hardness of 1.55 ± 0.15, 4.65 ± 0.44, 21.02 ± 0.42, 13.17 ± 0.13, 5.53 ± 0.89, 6.28 ± 0.19, 8.39 ± 0.14 GPa corresponding to α-Al matrix, Ni, Al3Ni2, Ni and Al3Ni2 interface, Al3Ni, and their respective interface. The composite containing 10 wt % Ni possesses the highest yield strength at room temperature. At 200 °C it could retain 54 % of its room temperature strength (91 MPa). The HR-TEM analysis shows that particulate and precipitation hardening was the predominant mechanisms during the initial stage of an isothermal compression. However, as the compression progressed, the pinning effect, dynamic recovery (DRV), and work hardening mechanisms became active. According to the current study findings, interface qualities substantially impact composite performance at both room temperature and elevated temperatures. The creation of strong intermetallic compounds (Al3Ni2 and Al3Ni) due to an intensive endothermic interaction between the Al and Ni particles is linked to this effect.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced materials and composites · Advanced ceramic materials synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (54)
Show source-provided references
1. Energy and emissions saving potential of additive manufacturing: the case of lightweight aircraft components10.1016/j.jclepro.2015.04.109 ↗
2. Lightweight in automotive components by forming technology10.1007/s42154-020-00103-3 ↗
3. Polmear · 2017
4. Effect of reinforcement concentration on the properties of hot extruded Al-Al2O3 composites synthesized through microwave sintering process10.1016/j.msea.2017.04.064 ↗
5. Strength-ductility balance strategy in SiC reinforced aluminum matrix composites via deformation-driven metallurgy
6. Using B4C nanoparticles to enhance thermal and mechanical response of aluminum10.3390/ma10060621 ↗
7. Enhancing thermal and mechanical response of aluminum using nanolength scale TiC ceramic reinforcement10.1016/j.ceramint.2018.02.135 ↗
8. Influence of metal powder premixing on mechanical behavior of dual reinforcement (Al2O3 (μm)/Si3N4 (nm)) in AA6061 matrix10.1016/j.jallcom.2017.10.002 ↗
9. Mechanical properties of Al-based metal matrix composites reinforced with Zr-based glassy particles produced by powder metallurgy10.1016/j.actamat.2009.01.010 ↗
10. A novel in-situ polymer derived nano ceramic MMC by friction stir processing10.1016/j.matdes.2015.07.054 ↗
11. Microstructural and mechanical characteristics of in situ metal matrix composites10.1016/S0927-796X(00)00024-3 ↗
12. Al-Al3Ti nanocomposites produced in situ by friction stir processing10.1016/j.actamat.2006.06.054 ↗
13. Metal matrix composites: production by the stir casting method10.1016/S0924-0136(99)00118-1 ↗
14. Fabrication, microstructure and mechanical properties of Al-Fe intermetallic particle reinforced Al-based composites10.1016/j.jallcom.2014.09.009 ↗
15. Simultaneously strengthening and toughening a core-shell structured particulate reinforced aluminum alloy-based composite by solid solution treatment10.1016/j.jallcom.2020.155765 ↗
16. Al-TiC composites in situ-processed by ingot metallurgy and rapid solidification technology: Part II. Mechanical behavior10.1007/s11661-998-0279-7 ↗
17. Combustion synthesis and densification of titanium diboride-copper matrix composite10.1016/S0167-577X(03)00338-0 ↗
18. Microstructure and mechanical behavior of high toughness Al-based metal matrix composite reinforced with in-situ formed nickel aluminides
19. A review on manufacturing the surface composites by friction stir processing10.1080/10426914.2020.1813897 ↗
20. Microstructural characterization and tribocorrosion behaviour of Al/Al3Ti and Al/Al3Zr FGMs10.1016/j.wear.2011.02.007 ↗
21. Core-shell structure mediated microstructure and mechanical properties of high entropy alloy CoCrFeNi/Al composites
22. Core-shell structure in situ reinforced aluminum matrix composites: microstructure, mechanical and tribological properties10.1016/j.jallcom.2005.05.002 ↗
23. Structural characterisation of unique core-shell shaped Al3Ni2/Al3Ni in-situ intermetallic in Al–4Cu-xNi via powder metallurgy (P/M)
24. Iron aluminide coatings on ferritic steels by CVD-FBR technology10.1016/j.intermet.2005.12.010 ↗
25. Fang · 2010
26. Mechanical properties of intermetallic phases in multi-component Al-Si alloys using nanoindentation10.1016/j.intermet.2009.02.003 ↗
27. Relationship between yield point phenomena and the nanoindentation pop-in behavior of steel10.1557/jmr.2011.208 ↗
28. Nanoindentation-induced deformation behavior in the vicinity of single grain boundary of interstitial-free steel10.2320/matertrans.46.2026 ↗
29. Grain boundary pop-in, yield point phenomenon and carbon segregation in aged low carbon steel10.2355/isijinternational.ISIJINT-2017-426 ↗
30. Investigation of mechanical properties of intermetallic phases in multi-component Al-Si alloys using hot-stage nanoindentation10.1016/j.intermet.2009.09.013 ↗
31. Numerical investigation of mechanical properties of aluminum-copper alloys at nanoscale10.1007/s11051-020-05137-6 ↗
32. Correlation of nanoindentation measurements of nickel made using geometrically different indenter tips10.1016/j.actamat.2005.10.048 ↗
33. Examination on the aging and tensile properties of Al-Zn-Mg/Al3Ni eutectic composite10.1007/s11661-002-0135-0 ↗
34. Recrystallization mechanisms and microstructure development in emerging metallic materials: a review
35. Characterization for dynamic recrystallization kinetics based on stress-strain curves
36. Effect of stacking fault energy on the dynamic recrystallization during hot working of FCC metals: a study using processing maps10.1007/BF02744618 ↗
37. Hot isostatic pressing synthesis and mechanical properties of Al/Al-Cu-Fe composite materials10.1557/jmr.2008.0111 ↗
38. Microstructure and mechanical properties of novel Al–Cu–Mg–Zn lightweight entropy alloys for elevated-temperature applications
39. Development of lightweight Al-based entropy alloys for elevated temperature applications
40. GmbH · 2016
41. International alloy designations and chemical composition limits for wrought aluminum and wrought aluminum alloys
42. Mechanical and thermal properties of nanocarbon-reinforced aluminum matrix composites at elevated temperatures10.1016/j.compositesb.2016.09.017 ↗
43. Microstructure and mechanical properties of two novel scrap tolerant Al65Cu10Mg10Si10Zn5 and Al80Cu5Mg5Si5Zn5 high entropy aluminum alloys
44. Hot deformation behavior and microstructure evolution of NiAl-9HfO2 composite
45. Characterization of Al3Zr precipitation via double-step homogenization and recrystallization behavior after subsequent deformation in 2195 Al-Li alloy
46. Segregation of Mg, Cu and their effects on the strength of Al Σ5 (210)[001] symmetrical tilt grain boundary10.1016/j.actamat.2017.12.023 ↗
47. Microstructure evolution and precipitation characteristics of spray-formed and subsequently extruded 2195 Al-Li alloy plate during solution and aging process
48. Dynamic recrystallization behavior and processing map of the 6082 aluminum alloy10.3390/ma13051042 ↗
49. Necklace formation during dynamic recrystallization of 5182 aluminium alloy under isothermal compression10.4028/www.scientific.net/MSF.812.167 ↗
50. Evolution of activation energy during hot deformation of AA7150 aluminum alloy10.1016/j.msea.2013.01.080 ↗
51. Particle reinforced aluminium and magnesium matrix composites10.1179/imr.1994.39.1.1 ↗
52. Strengthening in Al alloy nano composites fabricated by ultrasound assisted solidification technique10.1016/j.msea.2015.10.118 ↗
53. Prediction models for the yield strength of particle-reinforced unimodal pure magnesium (Mg) metal matrix nanocomposites (MMNCs)10.1007/s10853-013-7232-x ↗
54. Wang · 2014 · 246