journal article·2021-12

Structure and mechanical properties of WC interlayers between iron substrate and thin tungsten plate

Xiaolong Cai, Lei Guo, Baowei Cao, Xin Li, Mingxin Liu, Yunhua Xu

Vacuum· Volume 194
Publisher page

Abstract

Abstract To improve the mechanical properties of cast iron (Fe) surface, tungsten carbide (WC) interlayers were fabricated by the in-situ reaction at 1050 °C and 1100 °C for different heat-treatment times. The structure and phase composition of the layer were investigated via scanning electron microscopy, transmission electron microscopy and X-ray diffraction analyses. The effect of vacuum atmosphere temperature on the interfacial structure of sample was discussed. The results indicate that the thickness of the layer, consisting of a dominant WC phase, has a range of 11.12 ± 1.32 to 51.51 ± 1.36 μm obtained at 1050 °C. Based on growth kinetics, the diffusion coefficient of carbon in the WC layer is calculated to be 1 . 57 × 1 0 − 9 cm2/s. Furthermore, under the load of 100 mN, nanoindentation tests demonstrate that values of hardness and elastic modulus of the layer are approximately 25.09–39.74 GPa and 649.54–834.17 GPa, which are 2.4–3.8 times and 3.5–4.4 times larger than that of the substrate, respectively. By means of Vickers indentation mode using the available equation for Palmqvist crack system, the value of the calculated fracture toughness for the layer changes in a range from 2.55 ± 0.14 to 6.34 ± 0.54 MPa⋅m1/2, and the value decreases with the increasing load. This result may be caused by the reason that the fracture resistance also strongly depends on the applied load.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced materials and composites · Metal and Thin Film Mechanics · Diamond and Carbon-based Materials Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. Tribological study of gray cast iron with automotive brake linings: the effect of rotor microstructure10.1016/S0301-679X(02)00260-8 ↗
2. Microstructure, friction and wear of NbC coatings on a Fe substrate fabricated via an in situ reaction10.1016/j.surfcoat.2017.05.046 ↗
3. Pretreatments of gray cast iron with different inoculants10.1016/j.jallcom.2016.07.052 ↗
4. Nanomechanical characterization and fracture toughness of FeB and Fe2B iron borides produced by gas boriding of Armco iron10.1016/j.surfcoat.2017.07.020 ↗
5. Comparison in microstructure and mechanical properties of nanocomposite CrWN and nanolayered CrN/WN coatings10.1016/j.surfcoat.2005.07.042 ↗
6. Evaluation of growth behaviour of vanadium carbides-reinforced iron-based surface compound layer by in-situ reaction10.1016/j.vacuum.2019.04.057 ↗
7. Microstructure and tribology behaviors of in-situ WC/Fe carbide coating fabricated by plasma transferred arc metallurgic reaction10.1016/j.apsusc.2017.06.080 ↗
8. Microstructure and wear properties of selective laser melted WC reinforced 18Ni-300 steel matrix composite10.1016/j.vacuum.2018.04.044 ↗
9. Microstructure evolution, recrystallization and tribological behavior of TiC/WC composite ceramics coating10.1016/j.vacuum.2019.04.049 ↗
10. Microstructure-property relations in WC-Co coatings sprayed from combinatorial Ni-plated and nanostructured powders10.1016/j.matchar.2017.05.005 ↗
11. Erosive wear behavior of Cold-Sprayed Ni-WC composite coating10.1016/j.wear.2017.01.052 ↗
12. Fabrication, microstructure, and wear performance of WC-Fe composite/metal coating fabricated by resistance seam welding10.1016/j.matchar.2017.10.021 ↗
13. Microstructure evolution of Fe-based WC composite coating prepared by laser induction hybrid rapid cladding10.1016/j.apsusc.2010.05.079 ↗
14. Growth characteristics and mechanism of carbides precipitated in WC-Fe composite coatings by laser induction hybrid rapid cladding10.1016/j.jallcom.2010.06.115 ↗
15. Fabrication of WC/Fe composite coating by centrifugal casting plus in-situ synthesis techniques10.1016/j.surfcoat.2010.07.031 ↗
16. Microstructure and wear resistance of Fe-based WC coating by multi-track overlapping laser induction hybrid rapid cladding10.1016/j.optlastec.2011.06.017 ↗
17. Indentation modeling study of temperature-dependent fracture toughness of brittle coating on ductile substrate based on microcrack formation theory10.1016/j.surfcoat.2016.12.016 ↗
18. The effects of fine WC contents and temperature on the microstructure and mechanical properties of inhomogeneous WC-(fine WC-Co) cemented carbides10.1016/j.ceramint.2016.08.119 ↗
19. Cermet coatings with Fe-based matrix as alternative to WC-CoCr: mechanical and tribological behaviours10.1016/j.surfcoat.2012.03.094 ↗
20. Influences of the compositions and mechanical properties of HVOF sprayed bimodal WC-Co coating on its high temperature wear performance10.1016/j.ijrmhm.2017.08.012 ↗
21. WC-Fe layer with high volume fraction and fracture toughness on cast iron fabricated by in situ solid-phase diffusion10.1016/j.vacuum.2019.108801 ↗
22. Preparation of a gradient nanostructured surface TaC layer-reinforced Fe substrate by in situ reaction10.1016/j.jallcom.2017.04.081 ↗
23. Evaluation of fracture toughness of tantalum carbide ceramic layer: a vickers indentation method10.1007/s11665-016-2161-x ↗
24. Vickers indentation fracture toughness of Y-TZP dental ceramics10.1016/j.ijrmhm.2016.12.016 ↗
25. Evaluation of KIC of brittle solids by the indentation method with low crack-to-indent ratios10.1007/BF00724706 ↗
26. Vickers indentation fracture toughness test Part 1 Review of literature and formulation of standardised indentation toughness equations10.1179/mst.1989.5.9.865 ↗
27. Microhardness and fracture toughness of dental materials by indentation method10.1002/jbm.b.30371 ↗
28. A method to determine the fracture toughness brittle materials, especially hard metals
29. Growth kinetics and mechanical properties of boride layers formed at the surface of the ASTM F-75 biomedical alloy10.1016/j.surfcoat.2013.06.083 ↗
30. Kinetics of niobium carbide reinforced composite coating produced in situ10.1016/j.vacuum.2015.05.035 ↗
31. Evaluation and mechanisms on heat damage of WC particles in Ni60/WC composite coatings by laser induction hybrid cladding10.1016/j.ijrmhm.2016.11.001 ↗
32. Versatility of the sputtering technique in the processing of WC-Fe-Ni-Cr composites10.1016/j.surfcoat.2012.05.093 ↗
33. Three-point bending fatigue behavior of WC-Co cemented carbides10.1016/j.matdes.2012.08.075 ↗
34. Hardness of hexagonal tungsten carbide crystals as a function of orientation10.1016/j.actamat.2012.07.056 ↗