journal article·2020-06Open access

A comprehensive study of molybdenum boats behavior during service life for continuous thermal evaporation technique, used in thin film technology

Sina Rouhi, Jose Enrique Martinez-Medina, Mehtap Ozdemir, Mehmet Ertugrul, Gulnur Aygun, Lutfi Ozyuzer

Vacuum· Volume 176

Abstract

Abstract The aim of this study is to calculate the optimum lifetime of Molybdenum (Mo) thermal evaporation boats for Copper (Cu) filling in thin film technologies. Three types of Mo boats with thicknesses of 0.2, 0.3 and 0.5 mm were used during the experiments under the high vacuum condition about 6.0 × 10−6 Torr. The behavior of each boat was investigated by focusing on the total amount of evaporation material, operational time and applied power. Prior to the deposition process, material was loaded on the evaporation boat by two methods. In the first method, Cu wire was cut into 1 cm long, then every boat was filled with this amount of Cu material. The second alternative feeding method is to use a wire-feeder step motor, which refills boat with Cu wire during evaporation process. The latter one is very useful for continuous deposition process since there is no need to break the vacuum state. In both methods, however, the number of failures during operations increases after a series of experiments have been taken place because of boat aging. The results of failures have been analyzed by various methods, and it has been observed that thinner boats showed better stability for long time operation by continuous feeding technique.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Fluid Dynamics and Thin Films · Nanomaterials and Printing Technologies · Electronic Packaging and Soldering Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (29)

Show source-provided references
1. Adachi · 2012 · 3
2. Influence of gate metallization processes on the electrical characteristics of high-k/In0.53Ga0.47As interfaces
3. Influence of copper composition and reaction temperature on the properties of CZTSe thin films10.1016/j.jallcom.2016.04.309 ↗
4. Growth, structural and optical properties of copper indium diselenide thin films deposited by thermal evaporation method10.1016/j.solener.2008.11.006 ↗
5. Structural, electrical, and optical properties of copper indium diselenide thin film prepared by thermal evaporation method10.1016/j.tsf.2008.11.133 ↗
6. Characterization of the ITO/p-Si/Al contacts produced by thermal evaporation10.1016/j.vacuum.2019.108799 ↗
7. Fabrication and characterization of WO 3 thin films on silicon surface by thermal evaporation10.1016/j.matlet.2017.02.078 ↗
8. Nanostructured WO3 deposited by modified thermal evaporation for gas-sensing applications10.1016/j.tsf.2005.04.031 ↗
9. Preparation of large-scale cupric oxide nanowires by thermal evaporation method10.1016/j.jcrysgro.2003.08.012 ↗
10. Thermoelectric properties of V 2 O 5 thin films deposited by thermal evaporation10.1016/j.apsusc.2013.06.016 ↗
11. Structural, electrical and optical properties of AgInS2 thin films grown by thermal evaporation method10.1016/j.jpcs.2005.09.005 ↗
12. Temperature-controlled growth of silicon-based nanostructures by thermal evaporation of SiO powders10.1021/jp004253q ↗
13. Influence of substrate temperature on the physical properties of thermally evaporated nanocrystalline bismuth sulfide thin films10.1016/j.vacuum.2012.04.006 ↗
14. Colombo · 2010 · 2007
15. Master sintering curve concepts as applied to the sintering of molybdenum10.1007/s11661-006-0043-9 ↗
16. Fracture and ductile-to-brittle transition characteristics of molybdenum by impact and static bend tests10.2320/matertrans1989.36.504 ↗
17. On the recrystallization behavior of technically pure molybdenum10.1016/j.ijrmhm.2010.03.006 ↗
18. Growth of Cu 2 InO 4 thin films on Si substrate by thermal evaporation technique and enhancement of thermoelectric properties by post-growth annealing10.1016/j.physb.2019.03.023 ↗
19. Growth of Zn2GeO4 thin film by thermal evaporation on ITO substrate for thermoelectric power generation applications10.1016/j.ceramint.2018.09.168 ↗
20. Bogatin · 2010
21. Wettability versus roughness of engineering surfaces10.1016/j.wear.2010.03.029 ↗
22. Wettability versus roughness: multi-scales approach10.1016/j.triboint.2014.07.002 ↗
23. Kehrein · 2006
24. Grain boundary width, energy and self-diffusion in nickel: effect of material purity10.1016/j.actamat.2013.05.010 ↗
25. High-temperature thermal expansion of six metallic elements measured by dilatation method and X-ray diffraction10.1007/BF01174717 ↗
26. High temperature structure and thermal expansion of some metals as determined by x-ray diffraction data. I. Platinum, tantalum, niobium, and molybdenum10.1063/1.1699977 ↗
27. Grain boundary segregation in iron and its alloys and its effect on intergranular fracture10.4028/www.scientific.net/MSF.46.253 ↗
28. Level · 2008
29. The effect of heat treatment on mechanical characteristics and nature of failure of sheet molybdenum alloys