Study on microstructural and tribological properties of sulphonitrocarburized layers diffused by hollow cathode discharging
Source abstract
Abstract
Abstract In the present research, sulfurized, nitrided, nitrocarburized, and sulphonitrocarburized layers were diffused on the investigated specimens by hollow cathode diffusion, which was introduced as a new surface treatment method due to its numerous advantages over traditional diffusion methods. The structural morphologies, composition, phase structure, and tribological properties of different diffused layers were analyzed. It was found that both the sulfurized and sulphonitrocarburized layers were relatively porous compared with the other two diffused layers, especially the grain size and the microscopic roughness of the sulphonitrocarburized layer were much smaller than those of the sulfurized layer. The sulphonitrocarburized layer had the highest nano-hardness, the lowest friction coefficient, wear loss, and the smallest wear spot of the counterparts, which is superior over nitrided layer, nitrocarburized layer, and sulfurized layer. It benefited from the synergistic effect of the sulfurized layer and the nitrocarburized layer. This paper is significant for the protection of high-load high-speed friction pair s, exceptionally soft-hard pairs.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Lubricants and Their Additives · Tribology and Wear Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (48)
Show source-provided references
1. A comparative study on the tribological behaviors of nitrided and sulfur-nitrided 35CrMo steel lubricated in PAO base oil with MoDTC additive10.1016/j.triboint.2011.08.017 ↗
2. Effects during plasma nitriding of shaped materials of different sizes10.1016/S0257-8972(02)00887-3 ↗
3. Effect of workpiece geometry on the uniformity of nitrided layers10.1016/S0257-8972(00)01146-4 ↗
4. Negative effects of reactive sputtering in an industrial plasma nitriding10.1361/10599490523986 ↗
5. Intermediate stages of CrN precipitation during PIII nitriding of austenitic stainless steel10.1016/j.surfcoat.2014.08.007 ↗
6. Etc. Interpretation of glancing angle and bragg-brentano XRD measurements for CoCr alloy and austenitic stainless steel after PIII nitriding10.1109/TPS.2011.2160292 ↗
7. Etc. Enhancement of pitting corrosion resistance of austenitic stainless steel through deposition of amorphous/nanocrystalline oxy-nitrided phases by active screen plasma treatment10.1590/1980-5373-mr-2017-0697 ↗
8. etc. Microstructure and corrosion resistance of nitrogen-rich surface layers on AISI 304 stainless steel by rapid nitriding in a hollow cathode discharge
9. Etc. Effect of electric potentials on microstructure, corrosion and wear characteristic of the nitrided layer prepared on 2Cr13 stainless steel by plasma nitriding10.1007/s40195-018-0836-z ↗
10. Structure and friction-reducing property of sulfide layer produced by ion sulphuration
11. Influence of plasma nitriding temperature on microstructures and mechanical properties of Ti-N/Ti-Al multilayer coatings on the surface of 5083 Al alloys10.1016/j.surfcoat.2017.12.031 ↗
12. Couto, etc. The effect of plasma nitriding on the fatigue behavior of the Ti-6Al-4V alloy10.3390/ma12030520 ↗
13. Influence of processing parameters on the characteristics of surface layers of low-temperature plasma nitrocarburized AISI 630 martensitic stainless steel10.1007/s12540-017-6491-5 ↗
14. Etc. The phenomenon of high hardness values on the S-phase layer of austenitic stainless steel via screen plasma nitriding process10.4236/ampc.2018.86017 ↗
15. Kinetics of austenite layer growth on the surface of Fe-23Cr-2.4Mo ferritic stainless-steel during solution nitriding10.18869/acadpub.jame.36.2.55 ↗
16. Mittemeijer · 2013 · 4A · 619
17. Brunatto, etc. Low-temperature plasma nitrocarburizing of the AISI 420 martensitic stainless steel: microstructure and process kinetics10.1016/j.surfcoat.2015.03.039 ↗
18. Optimizing the mechanical properties of M50NiL steel by plasma nitrocarburizing10.1016/j.apsusc.2014.07.093 ↗
19. etc. Effect of plasma nitrocarburizing temperature on the wear behavior of AISI 4140 steel10.1016/j.surfcoat.2010.04.054 ↗
20. Development of highly hard and corrosion-resistant A286 stainless steel through plasma nitrocarburizing process10.1016/j.surfcoat.2015.09.017 ↗
21. etc. Surface properties of low alloy steel treated by plasma nitrocarburizing prior to laser quenching process10.1016/j.optlastec.2014.09.012 ↗
22. Mittemeijer · 2015
23. Use of a solid carbon precursor for DC plasma nitrocarburizing of AISI 4140 steel10.1016/j.vacuum.2017.12.033 ↗
24. Microstructure and tribological behavior of plasma sprayed NiCrAlY/WC-Co/cenosphere/solid lubricants composite coatings10.1016/j.surfcoat.2018.09.018 ↗
25. Effect of solid lubricants on friction and wear behavior of alloyed gray cast iron10.1007/s12046-012-0061-9 ↗
26. Friction-induced nano-structural evolution of graphene as a lubrication additive10.1016/j.apsusc.2017.10.119 ↗
27. etc. Characterization and friction-reduction performances of composite coating produced by laser cladding and ion sulfurizing10.1016/j.matlet.2015.02.098 ↗
28. Preparation of Cu2ZnSnS4 film by sulfurizing solution deposited precursors10.1016/j.apsusc.2012.07.137 ↗
29. Estimating antiwear properties of esters as potential lubricant-based oils using QSTR models with CoMFA and CoMSIA10.1007/s40544-017-0175-5 ↗
30. Influence of alumina/MWCNT hybrid nanoparticle additives on tribological properties of lubricants in turning operations10.1007/s40544-018-0199-5 ↗
31. Lubricating mechanisms of sulfurized olefin on oxynitride steel surface under boundary lubrication condition10.1016/0043-1648(95)06836-8 ↗
32. etc. Tribological properties of molybdenum ion-plated and ion-sulfurized composite coating on mild steel
33. An investigation on the tribological properties of multilayer graphene and MoS2 nanosheets as additives used in hydraulic applications10.1016/j.triboint.2015.12.006 ↗
34. Morphological and electrochemical study of sulfide/nitride nanostructure deposited through pulsed plasma electrolysis10.1007/s11665-017-2611-0 ↗
35. Investigation of tribological and physical behavior of sulfide film produced by DC -regime plasma electrolysis10.1016/j.surfcoat.2016.09.073 ↗
36. Tribological performance of novel nickel-based composite coatings with lubricant particles10.1007/s40544-018-0211-0 ↗
37. etc. Characterization and tribological properties of composite 3Cr13/FeS layer10.1016/j.surfcoat.2009.01.017 ↗
38. The friction–reduction model of the iron sulfide film prepared by plasma source ion sulfuration10.1016/j.surfcoat.2006.07.226 ↗
39. Effects of sulfuring treatment on microstructure and scratch resistance of W360 hot work die steel
40. etc. Wear and corrosion properties of AISI 420 martensitic stainless steel treated by active screen plasma nitriding10.1016/j.surfcoat.2017.09.021 ↗
41. Microstructure, mechanical and adhesive properties of CrN/CrTiAlSiN/WCrTiAlN multilayer coatings deposited on nitrided AISI 4140 steel10.1016/j.matchar.2018.11.017 ↗
42. etc. Validity of “sputtering and re-condensation” model in active screen cage plasma nitriding process10.1016/j.apsusc.2013.02.008 ↗
43. etc.Cathodic cage plasma nitriding (CCPN) of austenitic stainless steel (AISI 316): influence of the different ratios of the (N2/H2) on the nitrided layers properties10.1016/j.vacuum.2012.05.008 ↗
44. etc. Investigation of nitrogen mass transfer within an industrial plasma nitriding system I: the role of surface deposits10.1016/j.surfcoat.2009.08.029 ↗
45. etc. Investigation of nitrogen mass transfer within an industrial plasma nitriding system II: application of a biased screen10.1016/j.surfcoat.2009.08.030 ↗
46. A feasibility study of plasma nitriding of steel with an oxide layer on the surface10.1007/s10853-006-0484-y ↗
47. X-ray photoelectron spectroscopy: towards reliable binding energy referencing10.1016/j.pmatsci.2019.100591 ↗
48. etc. Tribological properties of sulfurized-nitrided layer prepared by a two-step method10.1016/j.vacuum.2011.02.011 ↗