journal article·2004-11

Uncertainty analysis of the high vacuum part of the orifice-flow-type pressure standard

L. Peksa, P. Řepa, T. Gronych, J. Tesař, D. Pražák

Vacuum· Volume 76· Issue 4
Publisher page

Abstract

Abstract The orifice-flow-type pressure standard is commonly accepted as primary standard for vacuum gauge calibration in the high vacuum gas pressure range. It consists of two parts—a high vacuum part and a flowmeter. Practical questions arising at design of the standard have to be answered based on the standard uncertainty analysis. The analysis of the uncertainty sources in the high vacuum part except deviations from the Maxwellian distribution is given in the paper. Uncertainty of a precise flowmeter is taken from references for comparison. It follows from the analysis that uncertainties caused by some sources at routinely achievable parameters are negligibly small and further improvement brings no benefit. The crucial quantities influencing the total uncertainty are the temperature of the chamber and the flowmeter, the outgassing rate from the inner surfaces, the ultimate pressure of the pump and the additional (detrimental) pumping speed. The pumping speed of the main pump has to be “sufficiently higher” than the orifice conductance.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Scientific Measurement and Uncertainty Evaluation · Advanced Sensor Technologies Research · Advanced Measurement and Metrology Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (25)

Show source-provided references
1. Poulter · J Phys E–Sci Instr · 1974 · 7 · 3910.1088/0022-3735/7/1/011 ↗
2. Poulter · J Phys E–Sci Instr · 1977 · 10 · 11210.1088/0022-3735/10/2/002 ↗
3. Peggs GN. The dynamic flow technique for the calibration of vacuum gauges. NPL Report MOM 1973;6.
4. Peggs GN. The dynamic flow technique for the calibration of vacuum gauges, Part 2: The measurement of gas throughput NPL Report MOM 1975;14.
5. ISO/DIS 3570/1, Vacuum gauges—standard methods for calibration —Part I.: Pressure reduction by continuous flow in the pressure range of 10−1 to 10−5 Pa (10−3 to 10−7 Torr). 112, 1975.
6. Hojo H, Ono M, Nakayama K. Proceedings of the Seventh International Vacuum Congress & Third International Conference on Solid Surfaces. Viena: 1977. p. 117.
7. McCulloh · J Vac Sci Technol A · 1986 · 4 · 36210.1116/1.573928 ↗
8. Tilford · J Vac Sci Technol A · 1988 · 6 · 28510.1116/1.575612 ↗
9. Bergoglio · Vacuum · 1988 · 38 · 88710.1016/0042-207X(88)90486-1 ↗
10. Calcatelli · Vacuum · 1989 · 39 · 79910.1016/0042-207X(89)90041-9 ↗
11. Jitschin · J Vac Sci Technol A · 1992 · 10 · 334410.1116/1.577823 ↗
12. Jousten · J Vac Soc Japan · 1994 · 37 · 67810.3131/jvsj.37.678 ↗
13. Jenko · Vacuum · 1995 · 46 · 81710.1016/0042-207X(95)00046-1 ↗
14. Levine · J Vac Sci Technol A · 1994 · 12 · 172710.1116/1.579045 ↗
15. Levine · J Vac Sci Technol A · 1996 · 14 · 129710.1116/1.579945 ↗
16. Mohan · Vacuum · 1995 · 46 · 81710.1016/0042-207X(95)00001-1 ↗
17. Jousten · Metrologia · 1999 · 36 · 49310.1088/0026-1394/36/6/2 ↗
18. Li Wangkui · Vacuum · 1999 · 53 · 16710.1016/S0042-207X(98)00358-3 ↗
19. Saitoh · J Vac Sci Technol A · 1993 · 11 · 281610.1116/1.578646 ↗
20. Watanabe Fumio · J Vac Sci Technol A · 1993 · 11 · 43210.1116/1.578749 ↗
21. Nesterov · Vacuum · 1999 · 53 · 19310.1016/S0042-207X(98)00361-3 ↗
22. Repa · Czech J Phys B · 1981 · 31 · 69510.1007/BF01596324 ↗
23. Koshmarov Yu A, Ryzhov Yu A. Prikladnaya dinamika razrezhonogo gaza. Moscow Mashinostroenie: 1977.
24. Butler · Vacuum · 1999 · 53 · 16310.1016/S0042-207X(98)00351-0 ↗
25. Communication of The Technical Department Leybold Vakuum GMBH.