journal article·2025-08Open access

Influence of different extrusion temperatures on microstructure and mechanical properties of Mg-Bi-Zn-Ca alloy

Ruizhi Zhang, Weiying Huang, Yu Liu, Juangang Zhao, Qian Ma, Zhezheng Ren, Xiaoyan Yang, Jing Wu, Yuanzhi Wu, Lijun Wang, Shang Zhou, Wenjie He, Yunpeng Liu

Vacuum· Volume 238

Abstract

The combination of Ca-doped magnesium alloy and hot extrusion process has garnered significant attention due to its exceptional mechanical properties. For this purpose, Mg-Bi-Zn-Ca alloy with a low Ca content is prepared and subjected to hot extrusion at temperatures of 225, 250, and 275 °C respectively. Subsequently, the impact of hot extrusion temperature on Mg alloy's microstructure and mechanical properties is further investigated through high-performance characterization techniques and tensile experiment. The Mg alloy demonstrates exceptional yield strength and ultimate tensile strength of 382.5 MPa and 392.4 MPa at 225 °C, surpassing other Mg alloys of the same type. The strengthening of the alloy primarily arises from the synergistic effect of grain boundary reinforcement and dislocation strengthening, as the Mg alloy exhibits a bimodal grain structure at 225 °C with the smallest average grain size . The interface between DRXed grains and unDRXed regions exhibits a high density of dislocations, accompanied by a significant presence of nanoscale precipitates within the matrix. These nanoscale precipitates act as effective pinning agents, restricting grain boundary expansion and impeding dislocation motion , thereby further augmenting the strengthening mechanism . Therefore, the low cost, high strength, and simple hot extrusion process make the Mg alloy have good industrial application potential.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Metal and Thin Film Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (51)

Show source-provided references
1. Development and application of magnesium alloy parts for automotive OEMs:A review10.1016/j.jma.2022.12.015 ↗
2. A review on developing high-performance ZE41 magnesium alloy by using bulk deformation and surface modification methods10.1016/j.jma.2023.03.001 ↗
3. Microstructure evolution, strengthening mechanisms and deformation behavior of high-ductility Mg-3Zn-1Y-1Mn alloy at different extrusion temperatures10.1016/S1003-6326(22)66117-X ↗
4. Tracing the effects of calcium, stannum, and zinc additions on the creep resistance of Mg–Al-based alloys10.1007/s11661-023-07050-8 ↗
5. The improved mechanical properties of Mg-Zn-Nd alloy with Ca addition via grain refinement and nano precipitates10.1016/j.msea.2023.145729 ↗
6. Improvement of severe plastic deformation realized by several passes rotary swaging in the microstructure and properties of Mg-0.6Mn-0.5Al-0.5Zn-0.4Ca alloy10.1016/j.msea.2023.144629 ↗
7. Effect of pre-stretching on the precipitation evolution and mechanical properties of GW63K magnesium alloy10.1016/j.msea.2023.145504 ↗
8. Effect of twin assisted precipitation on the microstructure and mechanical properties of gradient structure Mg-Gd-Zn-Zr alloy10.1016/j.vacuum.2023.112162 ↗
9. Effect of a compound modification process on the microstructure and mechanical properties of ZK60 magnesium alloys10.1016/j.msea.2020.139117 ↗
10. Microstructure and mechanical properties of Mg-14Li-1Al/MWCNTs composites prepared by electrophoretic deposition and accumulative roll bonding10.1016/j.jmapro.2021.10.040 ↗
11. Characterization of hot extrusion deformation behavior, texture evolution, and mechanical properties of Mg-5Li-3Sn-2Al-1Zn magnesium alloy10.1016/j.msea.2022.144136 ↗
12. Microstructure and properties of AZ61 ultra-fine grained magnesium alloy prepared by mechanical milling and powder metallurgy processing
13. Effects of Mg17Al12 phase on microstructure evolution and ductility in the AZ91 magnesium alloy during the continuous rheo-squeeze casting-extrusion process10.1016/j.jmst.2023.12.031 ↗
14. In-situ EBSD analysis of microstructural evolution and damage behavior of Mg-Al-Ca-Mn alloys with different extrusion ratios10.1016/j.matchar.2023.112781 ↗
15. Microstructure and mechanical and corrosion properties of hot-extruded Mg-Zn-Ca-(Mn) biodegradable alloys10.1016/j.jma.2020.11.008 ↗
16. Microstructure and properties of biomedical Mg-Zn-Ca alloy at different extrusion temperatures
17. Variation in dynamic deformation behavior and resultant yield asymmetry of AZ80 alloy with extrusion temperature10.1016/j.jmst.2019.11.033 ↗
18. Effects of extrusion parameters on the microstructure, corrosion resistance, and mechanical properties of biodegradable Mg-Zn-Gd-Y-Zr alloy10.1016/j.jallcom.2021.161964 ↗
19. Achieving superior mechanical properties in a low-alloyed magnesium alloy via low-temperature extrusion10.1016/j.msea.2022.143611 ↗
20. High strength-thermal conductivity Mg-Ga-Ca-Ce Sheet by hot-extrusion and rolling10.1007/s12540-023-01481-z ↗
21. Deformation mechanisms of Mg-Ca-Zn alloys studied by means of micropillar compression tests10.1016/j.actamat.2021.117151 ↗
22. Critical resolved shear stresses for slip and twinning in Mg-Y-Ca alloys and their effect on the ductility10.1016/j.ijplas.2023.103525 ↗
23. Mechanochemical characteristics of Ca-added Mg-based alloys: a multimodality approach10.1016/j.matchar.2020.110475 ↗
24. Investigations on a ternary Mg-Ca-Si wrought alloy extruded at moderate temperatures10.1016/j.matlet.2022.132633 ↗
25. The enhanced Zn and Ca co-segregation and mechanical properties of Mg-Zn-Ce alloy with micro Ca addition10.1016/j.msea.2023.144712 ↗
26. Exceptional creep resistance enabled by thermally stable cellular dislocation structures in an additively manufactured multicomponent alloy10.1016/j.msea.2023.145902 ↗
27. A promising strategy of multicomponent alloy intermedium for enhancing the mechanical performance of inertia friction welding joints of Inconel 718 alloys10.1016/j.msea.2024.146480 ↗
28. A coupled experimental and thermodynamic assessment of the Mg-Bi-Sb and Zn-Bi-Sb ternary system and extrapolate to the Mg-Bi-Zn-Sb system10.1016/j.tca.2022.179327 ↗
29. Unexpected effects on creep resistance of an extruded Mg-Bi alloy by Zn and Ca co-addition: experimental studies and first-principles calculations10.1016/j.jmst.2024.01.083 ↗
30. Achieving exceptional improvement of yield strength in Mg-Zn-Ca alloywire by nanoparticles induced by extreme plastic deformation10.1016/j.msea.2022.143733 ↗
31. Influence of Ca-Ce/La synergistic alloying on the microstructure and mechanical properties of extruded Mg-Zn alloy10.1016/j.msea.2017.09.113 ↗
32. Comparison of microstructure and mechanical properties of Mg-Zn microalloyed with Ca or Ce10.1016/j.vacuum.2018.02.029 ↗
33. Microstructure and mechanical and corrosion properties of hot-extruded Mg-Zn-Ca-(Mn) biodegradable alloys10.1016/j.jma.2020.11.008 ↗
34. Microstructure refinement,mechanical and biocorrosion properties of Mg-Zn-Ca-Mn alloy improved by a new severe plastic deformation process10.1016/j.jma.2020.11.013 ↗
35. Simultaneous enhancement of thermal conductivity and mechanical properties of EZ42 magnesium alloy by Ca microalloying
36. On the microstructure and mechanical properties of Mg-Gd alloy with combined Zn and Ca addition10.1007/s11665-022-07643-1 ↗
37. Significant improvement in mechanical properties of Mg-Zn-La alloy by minor Ca addition10.1016/j.matchar.2020.110130 ↗
38. Effects of Zn and Ca addition on microstructure and mechanical properties of as-extruded Mg-1.0Sn alloy sheet10.1016/j.msea.2019.01.028 ↗
39. Microstructure, mechanical properties and biomedical application of medical implantable extruded Mg-Zn-Zr-Ca alloy10.1088/2053-1591/ad1354 ↗
40. Effect of rolling temperature on mechanical properties and corrosion resistance of Al-Cu-Mg-Ag alloy10.1016/j.jallcom.2021.163168 ↗
41. Unveiling the formation of basal texture variations based on twinning and dynamic recrystallization in AZ31 magnesium alloy during extrusion10.1016/j.actamat.2018.07.014 ↗
42. Low-temperature high-speed extrusion of a multicomponent Mg-Bi base alloy and its heat resistance during hot tension10.1016/j.jallcom.2023.172187 ↗
43. Development of low-alloyed and rare-earth-free magnesium alloys having ultra-high strength10.1016/j.actamat.2018.03.002 ↗
44. Development of low-alloyed and rare-earth-free magnesium alloys having ultra-high strength10.1016/j.actamat.2018.03.002 ↗
45. Mechanistic investigation on Ce addition in tuning recrystallization behavior and mechanical property of Mg alloy10.1016/j.jmst.2022.05.042 ↗
46. Microstructure evolution and mechanical properties of a high strength Mg-11.7Gd-4.9Y-0.3Zr (wt%) alloy prepared by predeformation annealing, hot extrusion and ageing10.1016/j.msea.2017.06.096 ↗
47. Preparation of ultra-high strength Mg-Gd-Y-Zn-Zr alloy by pre-ageing treatment prior to extrusion10.1016/j.jallcom.2021.162490 ↗
48. Fabrication of exceptionally high-strength Mg-4Sm-0.6Zn-0.4Zr alloy via low-temperature extrusion10.1016/j.msea.2021.142565 ↗
49. Preparation of high-performance Mg-Gd-Y-Mn-Sc alloy by heat treatment and extrusion10.1016/j.jallcom.2022.167906 ↗
50. High strength and ductility AZ91 magnesium alloy with multi-heterogenous microstructures prepared by high-temperature ECAP and short-time aging10.1016/j.msea.2018.07.075 ↗
51. Mechanistic investigation of a low-alloy Mg-Ca-based extrusion alloy with high strength-ductility synergy10.1016/j.actamat.2020.01.017 ↗