Zero-length conflat fin-type nonevaporable getter pump deposited with oxygen-free palladium/titanium
Source abstract
Abstract
A zero-length conflat fin-type nonevaporable getter (NEG) pump deposited with oxygen-free palladium/titanium (Pd/Ti) has been developed. The NEG pump was activated by baking and its pumping speeds were measured as a function of baking time and baking temperature. The NEG pump can be fully activated by baking at 150 °C for 12 h and exhibits initial pumping speeds of 2340 L s−1 for H2, and 1440 L s−1 for CO. The initial pumping speeds of the oxygen-free Pd/Ti thin film after baking at 150 °C were estimated to be 3.2 L s−1 cm−2 for H2 and 7.6 L s−1 cm−2 for CO. The morphologies of oxygen-free Pd/Ti thin films on the partition plates and the bottom were examined by scanning electron microscopy, scanning transmission electron microscopy, and energy-dispersive X-ray spectroscopy. The Ti thin film was completely coated with Pd on the bottom, whereas the partition plates were covered by Pd/Ti nanostructures. The present NEG pump is ideal for maintaining ultrahigh vacuum below 10−8 Pa, because its pumping speeds for H2 and CO are quite large, and because it can be fully activated by baking at 150 °C for 12 h.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Innovative Microfluidic and Catalytic Techniques Innovation · Semiconductor materials and devices · Electronic and Structural Properties of Oxides
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (42)
Show source-provided references
1. A nonevaporable low temperature activatable getter material10.1116/1.570852 ↗
2. Evaluation of Zr–V–Fe getter pump for UHV system10.1116/1.572090 ↗
3. Obtention of pressures in the 10−14 torr range by means of a Zr-V-Fe non evaporable getter10.1016/0042-207X(93)90084-N ↗
4. Pumping characteristics of the St707 nonevaporable getter (Zr 70 V 24.6‐Fe 5.4 wt %)10.1116/1.580226 ↗
5. LEP vacuum system: present status10.1016/0042-207X(90)94121-6 ↗
6. Non evaporable getter (NEG) technology: a powerful tool for UHV-XHV systems10.1063/1.4732360 ↗
7. Non evaporable getter (NEG) pumps: a route to UHV-XHV10.1063/1.3215608 ↗
8. Low-cost, high-performance nonevaporable getter pumps using nonevaporable getter pills10.1116/1.4961050 ↗
9. Benvenuti · 1997
10. Nonevaporable getter films for ultrahigh vacuum applications10.1116/1.580963 ↗
11. Decreasing surface outgassing by thin film getter coatings10.1016/S0042-207X(98)00017-7 ↗
12. Influence of the elemental composition and crystal structure on the vacuum properties of Ti–Zr–V nonevaporable getter films10.1116/1.1414122 ↗
13. Vacuum properties of TiZrV non-evaporable getter films10.1016/S0042-207X(00)00246-3 ↗
14. Ti–Zr–V non-evaporable getter films: from development to large scale production for the Large Hadron Collider10.1016/j.tsf.2005.12.218 ↗
15. Nonevaporable getter coating chambers for extreme high vacuum10.1116/1.5010154 ↗
16. Pumping properties of Ti–Zr–Hf–V non-evaporable getter coating10.1016/j.vacuum.2013.07.035 ↗
17. Mase · 2018
18. Non-evaporable getter (NEG) coating using titanium and palladium vacuum sublimation10.1380/vss.61.227 ↗
19. Single metal zirconium non-evaporable getter coating
20. Benvenuti · 1998
21. Vacuum properties of palladium thin film coatings10.1016/j.vacuum.2003.12.022 ↗
22. Use of getter-catalyst thin films for enhancing ion pump vacuum performances10.1116/1.2731348 ↗
23. Efficient combining of ion pumps and getter palladium thin films10.1116/1.2834685 ↗
24. Depth-resolved analysis of subsurface hydrogen absorbed by Pd(100)10.1016/S0039-6028(01)00727-0 ↗
25. Dependence of effective desorption kinetic parameters on surface coverage and adsorption temperature: CO on Pd(111)10.1063/1.456294 ↗
26. Oxygen-free palladium/titanium coating, a novel nonevaporable getter coating with an activation temperature of 133 °C10.1116/1.5037023 ↗
27. Tsuji · 2005
28. Improved pumping speeds of oxygen-free palladium/titanium nonevaporable getter coatings and suppression of outgassing by baking under oxygen10.1116/1.5074160 ↗
29. Miyazawa · 2018 · 84
30. XPS study on the thermal stability of oxygen-free Pd/Ti thin film, a new non-evaporable getter (NEG) coating10.1063/1.5084676 ↗
31. Surface analysis and pumping speed measurements of oxygen-free palladium/titanium nonevaporable getter after heating at 100–450 °C10.1116/1.5111879 ↗
32. Hydrogen incorporation and release from nonevaporable getter coatings based on oxygen-free Pd/Ti thin films10.1116/1.5108983 ↗
33. Development of a new NEG pump using oxygen-free Pd/Ti thin film10.1063/1.5084677 ↗
34. Recommended procedure for measuring pumping speeds10.1116/1.574420 ↗
35. Sticking of molecular hydrogen on simple, noble and transition metal surfaces10.1080/01442359209353267 ↗
36. Malyshev · 2020
37. Test Particle Monte-Carlo modelling of installations for NEG film pumping properties evaluation10.1016/j.vacuum.2008.11.008 ↗
38. Interaction of hydrogen with solid surfaces10.1016/0167-5729(88)90009-X ↗
39. Adsorption of CO on Pd(100)10.1063/1.440430 ↗
40. A molecular beam investigation of He, CO, and O2 scattering from Pd(111)10.1063/1.436363 ↗
41. Review of sticking coefficients and sorption capacities of gases on titanium films10.1116/1.568900 ↗
42. Adsorption energetics of CO on supported Pd nanoparticles as a function of particle size by single crystal microcalorimetry10.1039/c1cp21677e ↗