journal article·2021-10Open access

Characterization of leakage, clamping force and retaining force of reusable sealing frame with elastomer O-ring for thin plasma polymeric coated thermoplastic polyester-ether films

Joachim Scheller, Pascal Joel Baur

Vacuum· Volume 192

Abstract

To apply thin films to tempered injection molds, an automatable sealing solution is necessary. The study investigates the required external clamping force for a sealing frame with O-ring, which is needed to enable leak-tight closure. The clamping of thin films for different hardness of elastomer O-rings and their compression were investigated in a tensile test machine. The important parameters for a low leakage of the sealing solution were identified by defined vacuum tests. The automation capability was assessed. The study revealed that high external clamping forces and low leakages are majorly dependent on high compression and high hardness of the O-ring. This results in a contact pressure, which is the primary criteria for the sealing performance of O-rings with a hardness of 15–75 Shore A. The results show that thin films made of thermoplastic polyester-ether tear in the tensile test at low compressions if the hardness of the O-ring exceeds 60 Shore A. Tearing occurs at lower compressions than needed for a sufficient sealing performance. Therefore, the choice of the O-ring and the dimension of the groove need to be based on the required sealing performance of the sealing frame and not on the fixture of thin films.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Injection Molding Process and Properties · Manufacturing Process and Optimization · Adhesion, Friction, and Surface Interactions

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (25)

Show source-provided references
1. The influence of void content on the structural flexural performance of unidirectional glass fibre reinforced polypropylene composites. Composites Part A10.1016/j.compositesa.2004.03.007 ↗
2. A revolutionary auxiliary film development for composite manufacturing10.1016/j.repl.2017.05.001 ↗
3. Bromination modification of butyl rubber and its structure, properties, and application10.1021/acs.iecr.9b03491 ↗
4. Gas transport in ethylene–propylene–diene (EPDM) elastomer: molecular simulation and experimental study10.1016/j.polymer.2007.07.020 ↗
5. Practical selection of elastomer materials for vacuum seals10.1116/1.570380 ↗
6. Permeability of common elastomers for gases over a range of temperatures10.1116/1.573005 ↗
7. Material properties of the seal gasket for shield tunnels: a review10.1016/j.conbuildmat.2018.10.021 ↗
8. Gas separation using polymer membranes: an overview10.1002/pat.1994.220051102 ↗
9. Rubber contact mechanics: adhesion, friction and leakage of seals10.1039/C7SM02038D ↗
10. Characterization of leakage through gaskets by a two-stage numeric approach using transport equations. In: ASME 2010 pressure vessels and piping conference: volume 2
11. A study of the relationship between frictional characteristics and surface condition of mechanical face seals10.1080/10402009108982064 ↗
12. Static sealing performance of gas mechanical seals including surface roughness and rarefaction effects10.1080/10402009808983779 ↗
13. Gasket characteristics for the design of bolted flange connections of metal-to-metal contact type10.1016/S0308-0161(01)00127-2 ↗
14. The temperature-dependence of some mechanical properties of a cured epoxy resin system10.1002/pen.760251305 ↗
15. A variability taxonomy to support automation decision-making for manufacturing processes10.1080/09537287.2019.1639840 ↗
16. The effects of level of automation and adaptive automation on human performance, situation awareness and workload in a dynamic control task10.1080/1463922021000054335 ↗
17. Levels of automation in manufacturing
18. Chemical and electrical properties of HMDSO plasma coated polyimide10.1016/j.vacuum.2012.12.009 ↗
19. 2018
20. 2008
21. Influence of fiber orientation and adhesion properties on tailored fiber-reinforced elastomers10.1007/s10443-020-09802-w ↗
22. Investigation of static and dynamic seal performances of a rubber O-ring10.1115/1.4038959 ↗
23. Design of elastomer O-ring vacuum seals10.1016/0042-207X(73)92117-9 ↗
24. Flow and heat transfer inside thin films supported by soft seals in the presence of internal and external pressure pulsations10.1016/S0017-9310(02)00220-X ↗
25. Heat sealing of semicrystalline polymer films. I. Calculation and measurement of interfacial temperatures: Effect of process variables on seal properties10.1002/app.1994.070510111 ↗