journal article·2022-05

Synthesis and characterization of Ta–B–C coatings prepared by DCMS and HiPIMS co-sputtering

M. Polaček, P. Souček, M. Alishahi, N. Koutná, P. Klein, L. Zábranský, Zs. Czigány, K. Balázsi, P. Vašina

Vacuum· Volume 199
Publisher page

Abstract

This study reports on the deposition and properties of Ta–B–C coatings by the co-sputtering of tantalum, boron carbide, and graphite targets using High Power Impulse Magnetron Sputtering (HiPIMS). It was possible to affect the microstructure of the deposited coatings by altering the deposition temperature or by the application of RF induced self-bias on the substrates without changing their chemical composition. The only identified crystalline phase from the Ta–B–C system present was TaC. The boron content in the coatings shows that the TaC crystallite size can be changed by a factor of 10 by changing the power to the boron carbide target. Mechanical properties of the coatings measured directly after the synthesis yield hardness higher than 40 GPa. After the relaxation of internal stress in the coatings (after one year) and changes in the structure, the hardness of all coatings was close to 36 GPa. According to ab initio calculations, the B incorporation in the fcc lattice of TaC in combination with C vacancies lead to lower (higher) shear-to-bulk modulus ratio (Poisson’s ratio), providing a good basis for improved ductility. All in all, Ta–B–C system shows a good potential as a novel hard protective coating.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Diamond and Carbon-based Materials Research · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (71)

Show source-provided references
1. The search for novel, superhard materials10.1116/1.581977 ↗
2. Structural, elastic, and high-pressure properties of cubic TiC, TiN, and TiO10.1103/PhysRevB.53.3072 ↗
3. Single layer and multilayer wear resistant coatings of (Ti,Al)N: A review10.1016/S0921-5093(02)00259-9 ↗
4. Mechanical properties of nanophase metals10.1016/0965-9773(95)00044-5 ↗
5. A proposal for an unusually stiff and moderately ductile hard coating material: Mo2BC10.1088/0022-3727/42/18/185406 ↗
6. XCII. Relations between the elastic moduli and the plastic properties of polycrystalline pure metals10.1080/14786440808520496 ↗
7. Theoretical predictions of structure and related properties of intermetallics10.1179/mst.1992.8.4.345 ↗
8. Systematic study on the electronic structure and mechanical properties of X2BC (X=Mo, Ti, V, Zr, Nb, Hf, Ta and W)10.1088/0953-8984/25/4/045501 ↗
9. Low temperature synthesis of Mo2BC thin films10.1016/j.tsf.2013.07.021 ↗
10. Are Mo2BC nanocrystalline coatings damage resistant? Insights from comparative tension experiments10.1016/j.surfcoat.2016.02.010 ↗
11. On the study of the mechanical properties of Mo-B-C coatings*10.1051/epjap/2016150591 ↗
12. Synthesis and characterisation of Mo-B-C thin films deposited by non-reactive DC magnetron sputtering10.1016/j.surfcoat.2016.12.003 ↗
13. Interaction of al with O2 exposed Mo2BC
14. Thermal stability of hard nanocomposite Mo-B-C coatings10.1016/j.vacuum.2016.12.016 ↗
15. Fracture toughness of Mo2BC thin films: Intrinsic toughness versus system toughening10.1016/j.matdes.2018.05.015 ↗
16. Fracture resistance enhancement in hard Mo-B-C coatings tailored by composition and microstructure10.1155/2018/5184584 ↗
17. Microstructural changes of amorphous Mo–B–C coatings upon thermal annealing10.1016/j.surfcoat.2019.125052 ↗
18. Study of W-B-C thin films prepared by magnetron sputtering using a combinatorial approach
19. Evolution of structure and mechanical properties of hard yet fracture resistant W-B-C coatings with varying C/W ratio10.1016/j.surfcoat.2018.02.054 ↗
20. The tribological properties of short range ordered W-B-C protective coatings prepared by pulsed magnetron sputtering10.1016/j.surfcoat.2018.10.026 ↗
21. Effect of bonding structure on hardness and fracture resistance of W-B-C coatings with varying b/w ratio10.1016/j.surfcoat.2018.12.007 ↗
22. Composition and mechanical properties of B-C-W and B-C-Ti thin films prepared by pulse magnetron sputtering10.1016/j.surfcoat.2016.07.107 ↗
23. Effect of carbon content on microstructures, mechanical and tribological properties and thermal stability in WBC films
24. Tantalum as a material of construction for the chemical processing industry – A critical survey10.1002/maco.19950461206 ↗
25. Corrosion of tantalum and niobium and their alloys10.1016/B978-044452787-5.00102-5 ↗
26. Growth of tantalum boride films by RF magnetron sputtering10.1149/1.1603253 ↗
27. Composition, structure, and properties of tantalum boride nanostructured films10.1134/S1063784206100136 ↗
28. Phase formation, structure, and state of stress of nanostructured tantalum boride films10.1134/S0031918X07010103 ↗
29. A universal trend of structural , mechanical and electronic properties in transition metal ( M=V , Nb , and Ta ) borides : First-principle calculations10.1016/j.commatsci.2012.07.021 ↗
30. Preparation of different morphology of TaCx whiskers10.1016/S0167-577X(02)00455-X ↗
31. Applied surface science stoichiometry behavior of TaN , TaCN and TaC thin films produced by magnetron sputtering10.1016/j.apsusc.2013.03.028 ↗
32. Nanostructured TaC film deposited by reactive magnetron sputtering: Influence of gas concentration on structural, mechanical, wear and corrosion properties10.1016/j.ceramint.2019.01.055 ↗
33. Review article: Tracing the recorded history of thin-film sputter deposition: From the 1800s to 201710.1116/1.4998940 ↗
34. High power impulse magnetron sputtering discharge10.1116/1.3691832 ↗
35. A novel pulsed magnetron sputter technique utilizing very high target power densities10.1016/S0257-8972(99)00292-3 ↗
36. High power pulsed magnetron sputtering: A review on scientific and engineering state of the art10.1016/j.surfcoat.2009.11.013 ↗
37. Ionized sputter deposition using an extremely high plasma density pulsed magnetron discharge Ionized sputter deposition using an extremely high plasma density pulsed magnetron discharge
38. Ionization of sputtered metals in high power pulsed magnetron sputtering Ionization of sputtered metals in high power pulsed magnetron sputtering
39. Mass and energy resolved detection of ions and neutral sputtered species incident at the substrate during reactive magnetron sputtering of Ti in mixed Ar + N2 mixtures mass and energy resolved detection of ions and neutral sputtered species incident at th
40. Low friction CrN / TiN multilayer coatings prepared by a hybrid high power impulse magnetron sputtering / DC magnetron sputtering deposition technique low friction CrN / TiN multilayer coatings prepared by a hybrid high power impulse magnetron sputtering10.1016/j.tsf.2010.05.061 ↗
41. Influence of dcMS and HPPMS in a dcMS/HPPMS hybrid process on plasma and coating properties10.1016/j.tsf.2016.07.079 ↗
42. Energy-enhanced deposition of copper thin films by bipolar high power impulse magnetron sputtering10.1016/j.surfcoat.2018.12.079 ↗
43. Microstructural control of TiC/a-C nanocomposite coatings with pulsed magnetron sputtering10.1016/j.actamat.2007.10.025 ↗
44. The effect of chemical composition on the structure, chemistry and mechanical properties of magnetron sputtered W-B-C coatings: Modeling and experiments
45. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
46. Efficient iterative schemes for ab initio total-energy calculations using a plane-wave basis set10.1103/PhysRevB.54.11169 ↗
47. From ultrasoft pseudopotentials to the projector augmented-wave method10.1103/PhysRevB.59.1758 ↗
48. Self-consistent equations including exchange and correlation effects10.1103/PhysRev.140.A1133 ↗
49. Generalized gradient approximation made simple10.1103/PhysRevLett.77.3865 ↗
50. Special points for Brillouin-zone integrations10.1103/PhysRevB.13.5188 ↗
51. Symmetry-general least-squares extraction of elastic data for strained materials from ab initio calculations of stress
52. Symmetry-general least-squares extraction of elastic coefficients from ab initio total energy calculations
53. Calculations of single-crystal elastic constants made simple10.1016/j.cpc.2009.11.017 ↗
54. Bestimmung der inneren struktur und der größe von kolloidteilchen mittels röntgenstrahlen
55. The scherrer formula for X-Ray particle size determination10.1103/PhysRev.56.978 ↗
56. Target material pathways model for high power pulsed magnetron sputtering10.1116/1.1865133 ↗
57. Microstructure and properties of nanocomposite Ti–B–N and Ti–B–C coatings10.1016/S0257-8972(99)00489-2 ↗
58. Non-reactively sputtered ultra-high temperature Hf–C and Ta–C coatings10.1016/j.surfcoat.2016.11.073 ↗
59. Influence of carbon deficiency on phase formation and thermal stability of super-hard TaCy thin films10.1016/j.scriptamat.2018.02.030 ↗
60. On the significance of the H/E ratio in wear control: A nanocomposite coating approach to optimised tribological behaviour10.1016/S0043-1648(00)00488-9 ↗
61. Relationships between hardness, Young’s modulus and elastic recovery in hard nanocomposite coatings10.1016/S0257-8972(01)01714-5 ↗
62. Nanostructured TiC/a-C coatings for low friction and wear resistant applications10.1016/j.surfcoat.2004.10.106 ↗
63. Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions10.1016/j.pmatsci.2013.09.002 ↗
64. Grain size and alloying effects on dynamic recovery in nanocrystalline metals10.1016/j.actamat.2016.08.019 ↗
65. Refining grains of metals through plastic deformation: Toward grain size limits10.1021/accountsmr.0c00075 ↗
66. Verhoeven · 1975 · 567
67. Review Article: Stress in thin films and coatings: Current status, challenges, and prospects10.1116/1.5011790 ↗
68. High-temperature properties of nanocomposite TiBxNy and TiBxCy coatings10.1016/S0257-8972(00)00887-2 ↗
69. A comparative study on reactive and non-reactive unbalanced magnetron sputter deposition of TiN coatings10.1016/S0040-6090(02)00511-4 ↗
70. The interrelationship between internal stress, processing parameters and microstructure of physically vapour deposited and thermally sprayed coatings
71. The influence of thermal annealing on residual stresses and mechanical properties of arc-evaporated TiCxN1-x (x=0, 0.15 and 0.45) thin films10.1016/S1359-6454(02)00365-8 ↗