journal article·2019-07

Optimisation of the RGA location in the evaluation of NEG coating pumping properties

Omid Seify, Oleg B. Malyshev, Rūta Širvinskaitė, Reza Valizadeh, AdrianN. Hannah

Vacuum· Volume 165
Publisher page

Abstract

Abstract Non-evaporable getter (NEG) coatings are widely used in vacuum chambers of particle accelerators. Vacuum solutions group at STFC Daresbury Laboratory is continuously developing and optimising the NEG coatings are for various applications and vacuum chamber geometries. The pumping properties of the NEG coatings are characterised by sticking probability and pumping capacity. Initial sticking probability of the NEG coated tube can be measured by gas injection at one end of the tube and partial pressure measurements at either sides, P1 and P2 respectively. This requires the NEG coating facility to be modelled with the Test Particle Monte-Carlo (TPMC) method to obtain the pressure ratio R = P1/P2 as a function of sticking probability, R(α), for each type and geometry of the with each of the NEG coated tubes. The purpose of TPMC modelling reported in this paper was to find R(α) for the NEG coating evaluation facility with a sample in a form of the 0.5-m long NEG coated tubes with inner diameters of 5, 7, 9 and 38 mm. Furthermore, the effect of RGA2 location was also studied. It has been demonstrated that the RGA2 location could significantly (from a few percent up to a factor 3.1) affect the pressure ratio R(α). The effect of pressure measurement errors on calculated sticking probability was studied for ΔR/R = 10, 20 and 50%. The sticking probability accuracy varies: Δα/α = 0.04–0.5 for ΔR/R = 10%, Δα/α = 0.07–0.8 for ΔR/R = 20% and Δα/α = 0.23–2.0 for ΔR/R = 50%.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Gas Dynamics and Kinetic Theory · Scientific Measurement and Uncertainty Evaluation · Plasma Diagnostics and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (28)

Show source-provided references
1. Benvenuti · 1998 · 200
2. A new pumping approach for the large electron positron collider (LEP)10.1016/0167-5087(83)90003-0 ↗
3. A novel route to extreme vacua: the non-evaporable getter thin film coatings10.1016/S0042-207X(98)00377-7 ↗
4. Operational experience and relation to deposition process for NEG-coated chambers installed on the ESRF electron storage ring10.1016/j.vacuum.2005.11.051 ↗
5. Status of NEG coating at ESRF
6. Kersevan · 2002 · 2565
7. Ten years of ELETTRA vacuum system experience10.1016/j.vacuum.2003.12.016 ↗
8. Performance of insertion device vacuum chambers at ELETTRA
9. Mazzolini · 2002
10. Design modelling and measured performance of the vacuum system of the Diamond Light Source storage ring10.1016/j.vacuum.2012.03.015 ↗
11. Herbeaux · 2008 · 3711
12. Herbeaux · 2008 · 3696
13. Development and production of non evaporable getter coatings for the vacuum chambers of the 3 GeV storage ring of MAX IV
14. The vacuum system of MAX IV storage rings: installation and conditioning
15. Costa Pinto · 2015
16. LHC: the world's largest vacuum systems being operated at CERN10.1016/j.vacuum.2009.05.015 ↗
17. Test Particle Monte-Carlo modelling of installations for NEG film pumping properties evaluation10.1016/j.vacuum.2008.11.008 ↗
18. Activation and measurement of nonevaporable getter films10.1116/1.3081969 ↗
19. Pumping properties of Ti–Zr–Hf–V non-evaporable getter coating10.1016/j.vacuum.2013.07.035 ↗
20. Test particle Monte Carlo simulation of NEG coated narrow tubular samples
21. Monte Carlo calculation of molecular flow rates through a cylindrical elbow and pipes of other shapes10.1063/1.1735797 ↗
22. Free molecular conductance of a cylindrical tube with wall sorption10.1116/1.1492459 ↗
23. Introduction to MOLFLOW+: new graphical processing unit-based Monte Carlo code for simulating molecular flows and for calculating angular coefficients in the compute unified device architecture environment10.1116/1.3153280 ↗
24. Gas dynamics modelling for particle accelerators10.1016/j.vacuum.2012.03.047 ↗
25. Workshop on measurement characteristics and use of quadrupole mass spectrometers for vacuum applications
26. In situ ultrahigh vacuum residual gas analyzer “calibration,”10.1116/1.2990856 ↗
27. Electron-stimulated desorption from polished and vacuum fired 316LN stainless steel coated with Ti-Zr-Hf-V10.1116/1.4897932 ↗
28. Electron stimulated desorption from bare and nonevaporable getter coated stainless steels10.1116/1.3478672 ↗