journal article·2019-11

A modified reference area method to estimate creep behaviour of service-exposed Cr5Mo based on spherical indentation creep test

Wenbin Lu, Xiang Ling, Sisheng Yang

Vacuum· Volume 169
Publisher page

Abstract

Abstract In this study, indentation creep tests under different conditions were conducted using a self-designed vacuum high-temperature indentation creep device to investigate the creep properties of service-exposed Cr5Mo. A microstructure test was also conducted and a prominent pile-up was found on the surface of the specimen. We performed a comprehensive finite element analysis to evaluate the non-uniform deformation characteristics of the spherical indentation creep test. The stress distribution and stress evolution for indenters with different diameters were also estimated during the test. Subsequently, considering the difficulty of calculating the equivalent stress owing to the area variation during spherical indentation, a modified reference area method was proposed. Based on a load relaxation simulation and geometric factor analysis, a general formula for the reference areas of indenters with different diameters was given. Thus, the equivalent stress during spherical indentation could be calculated, and the creep behaviour of service-exposed Cr5Mo was estimated. The results when using the modified method in this study demonstrated good consistency with the results obtained by the standard method. To sum up, the spherical indentation creep test has prominent advantages over the uniaxial tensile creep test in the analysis of in-service components.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Advanced materials and composites · Orthopaedic implants and arthroplasty

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (30)

Show source-provided references
1. Influence of specimen thickness on the creep behavior of a directional solidification nickel-based superalloy10.1016/j.vacuum.2018.01.032 ↗
2. A review of analysis methods for sub-micron indentation testing10.1016/S0042-207X(00)00377-8 ↗
3. Impression creep technique—an overview10.1016/j.msea.2005.05.110 ↗
4. Impression creep; a new creep test10.1007/BF00552241 ↗
5. Study of crystallographic creep parameters of nickel-based single crystal superalloys by indentation method10.1016/j.msea.2007.07.038 ↗
6. Indentation creep behaviors of Mg61Cu28Gd11 and (Mg61Cu28Gd11)99.5Sb0.5 bulk metallic glasses at room temperature10.1016/S1002-0721(10)60441-3 ↗
7. A potential method for determining the haz properties in welds using two-material impression creep test
8. Depth sensing indentation of linear viscoelastic–plastic solids: a simple method to determine creep compliance10.1016/j.engfracmech.2008.06.012 ↗
9. Impression creep of β-tin single crystals10.1016/0025-5416(79)90164-2 ↗
10. Experimental and numerical study of the method to determine the creep parameters from the indentation creep testing
11. Mechanical testing of thin films10.1179/imr.1994.39.1.24 ↗
12. A numerical approach to spherical indentation techniques for material property evaluation10.1016/j.jmps.2005.04.007 ↗
13. High-temperature creep property of high-Cr ferritic heat-resisting steel identified by indentation test10.1115/1.4033943 ↗
14. A method to identify steady creep strain from indentation creep using a new reference area of indentation10.1007/s11664-014-3196-0 ↗
15. Deep penetration of polycarbonate by a cylindrical punch10.1016/0167-6636(92)90020-E ↗
16. On the plastic flow of metals under conditions of axial symmetry10.1098/rspa.1955.0262 ↗
17. A new modified expanding cavity model for characterizing the spherical indentation behavior of bulk metallic glass with pile-up10.1016/j.scriptamat.2007.01.017 ↗
18. A holistic inverse approach based on a multi-objective function optimisation model to recover elastic-plastic properties of materials from the depth-sensing indentation test10.1016/j.jmps.2019.04.001 ↗
19. Creep characteristics and deformation analysis of service-exposed material using small punch creep test10.1016/j.engfracmech.2018.04.025 ↗
20. Effect of Mg and semi solid processing on microstructure and impression creep properties of A356 alloy10.1016/S1003-6326(13)62763-6 ↗
21. The impression creep behavior and microstructure evolution of cast and cast-then-extruded Mg–10Gd–3Y–0.5Zr (wt%)10.1016/j.msea.2015.10.001 ↗
22. A simple model for indentation creep10.1016/j.jmps.2018.01.001 ↗
23. Finite element analysis of plastic deformation during impression creep10.1007/s11665-014-1225-z ↗
24. Contact size-independent method for estimation of creep properties with spherical indentation10.1016/j.commatsci.2015.11.044 ↗
25. Impression creep deformation behaviour of 316LN stainless steel10.1179/1878641315Y.0000000004 ↗
26. Surface pile-up patterns in indentation testing of Cu single crystals10.1007/s11340-014-9883-1 ↗
27. Finite element analysis of spherical indentation to study pile-up/sink-in phenomena in steels and experimental validation10.1016/j.ijmecsci.2011.09.009 ↗
28. Characterization of plastic deformation in a disk bend test10.1016/S0022-3115(01)00484-6 ↗
29. Characterization of fatigue crack growth of concrete mortar under cyclic indentation loading10.1016/j.engfailanal.2017.10.004 ↗
30. Similarity analysis of creep indentation tests10.1098/rspa.1992.0038 ↗