journal article·2012-02

Sputter deposited low-friction and tough Cr–Si3N4 nanocomposite coatings on plasma nitrided M2 steel

Harish C. Barshilia, B. Deepthi, G. Srinivas, K.S. Rajam

Vacuum· Volume 86· Issue 8
Publisher page

Abstract

Abstract Nanocomposite coatings of Cr–Si 3 N 4 exhibiting low friction and high toughness were prepared on plasma nitrided AISI M2 steel substrates using an unbalanced magnetron sputtering system. The surface morphology and cross-sectional microstructure of the Cr–Si 3 N 4 nanocomposite coatings were studied using field emission scanning electron microscopy (FESEM) techniques. Cr–Si 3 N 4 nanocomposite coatings prepared at 48 at.% Cr exhibited a dense microstructure with nanoindentation hardness and toughness values of 18 GPa and 2.0 MPam ½ , respectively. Nanoscratch measurements indicated that Cr–Si 3 N 4 nanocomposite coatings exhibited good adhesion with a maximum critical load of 150 mN. Ball-on-disc reciprocating tests at a load of 2 N showed that Cr–Si 3 N 4 nanocomposite coatings prepared at 48 at.% Cr exhibited an average friction coefficient of 0.30. FESEM studies of the wear tracks indicated that there was no significant wear loss and the Cr–Si 3 N 4 nanocomposite coatings exhibited only mild wear due to oxidation.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Diamond and Carbon-based Materials Research · Tribology and Wear Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (40)

Show source-provided references
1. Pye · 2003
2. Influence of the microstructure on steel hardening in pulsed plasma nitriding10.1116/1.2889395 ↗
3. Effects of DC plasma nitriding parameters on microstructure and properties of 304L stainless steel10.1016/j.matchar.2008.08.011 ↗
4. Influence of the process temperature on the steel microstructure and hardening in pulsed plasma nitriding10.1016/j.surfcoat.2005.11.137 ↗
5. Hard yet tough nanocomposite coatings – present status and future trends10.1002/ppap.200600179 ↗
6. Toughness and toughening of hard nanocomposite coatings
7. Realising the potential of duplex surface engineering10.1016/S0301-679X(98)00015-2 ↗
8. Plasma diffusion treatment and duplex treatment-recent development and new applications
9. Wear resistance and anti-sticking properties of duplex treated forming tool steel10.1016/S0043-1648(03)00322-3 ↗
10. Duplex treatment: W-Ti-N sputtered coatings on pre-nitrided low and high alloy steels10.1016/j.surfcoat.2005.04.056 ↗
11. First results on duplex coatings without intermediate mechanical treatment10.1016/S0257-8972(03)00578-4 ↗
12. Characterization of duplex and non-duplex (Ti, Al)N and Cr-N PVD coatings10.1016/S0921-5093(01)01953-0 ↗
13. Transition metal nitride based nanolayered multilayer coatings and nanocomposite coatings as novel superhard materials
14. Supertough wear-resistant coatings with ‘chameleon’ surface adaptation10.1016/S0040-6090(00)00917-2 ↗
15. Toughening of hard nanostructural thin films: a critical review10.1016/j.surfcoat.2004.10.020 ↗
16. Mechanical properties of nanostructured copper- hydrogenated amorphous carbon composite films studied by nanoindentation10.1016/j.surfcoat.2003.10.117 ↗
17. Design and characterization of nanostructured metal/carbon composite films10.1016/j.surfcoat.2003.10.077 ↗
18. Mechanical and tribological properties of duplex treated TiN, nc-TiN/a-SiNx and nc-TiCN/a-SiCN coatings deposited on 410 low alloy stainless steel10.1016/j.surfcoat.2009.03.009 ↗
19. Investigation of mechanical properties of TiN + MoSx coating on plasma-nitrided substrate10.1016/j.surfcoat.2005.08.085 ↗
20. Characterization of Cu/Ni multilayer coatings by nanoindentation and atomic force microscopy10.1016/S0257-8972(02)00008-7 ↗
21. Influence of sample geometry on the effect of pulse plasma nitriding of M2 steel10.1016/S0257-8972(98)00721-X ↗
22. Effect of the initial microstructure on the plasma nitriding behavior of AISI M2 high speed steel10.1016/j.surfcoat.2010.05.042 ↗
23. Microstructure and residual stresses of a plasma nitrided M2 tool steel10.1016/S0257-8972(99)00063-8 ↗
24. MC complex carbide in AISI M2 high-speed steel10.1016/j.matlet.2008.11.035 ↗
25. Tool steels
26. Growth and structural characterization of yttria-stabilized zirconia-gold nanocomposite films with improved toughness10.1016/S0040-6090(01)01615-7 ↗
27. Structure and mechanical properties of DC magnetron sputtered TiC/Cu films10.1016/j.vacuum.2006.07.013 ↗
28. Mangalaraj. A study on the influence of copper content in CrN/Cu nanocomposite thin films prepared by pulsed DC magnetron sputtering10.1166/jnn.2009.1129 ↗
29. Nanomechanical and nanotribological properties of carbon, chromium, and titanium carbide ultrathin films10.1115/1.1330737 ↗
30. Mechanical properties of sputtered silicon nitride thin films10.1063/1.1626799 ↗
31. Investigation of mechanical and tribological properties of amorphous diamond-like carbon coatings10.1016/S0301-679X(97)00027-3 ↗
32. Quaternary hard nanocomposite TiCxNy/SiCN coatings prepared by plasma enhanced chemical vapor deposition10.1016/j.tsf.2004.03.043 ↗
33. Fischer-Cripps · 2004
34. Elastic/plastic indentation damage in ceramics: the median/radial crack system10.1111/j.1151-2916.1980.tb10768.x ↗
35. Mechanical properties of nanocomposite metal-ceramic thin films10.1016/j.compositesb.2003.08.005 ↗
36. Magnetron-sputtered nc-TiC/a-C(Al) tough nanocomposite coatings10.1016/j.tsf.2004.04.007 ↗
37. The toughening of alumina with nickel inclusions10.1016/0955-2219(90)90032-B ↗
38. Ductile phase toughened brittle materials
39. Failure modes in scratch adhesion testing10.1016/0257-8972(91)90188-3 ↗
40. Influence of plasma nitriding on wear performance of TiN coating10.1016/0257-8972(94)90105-8 ↗