UNS S32707 hyper-duplex stainless steel processed by powder injection molding and supersolidus liquid-phase sintering in nitrogen sintering atmosphere
Source abstract
Abstract
Abstract UNS S32707 hyper-duplex stainless steel (HDSS) was prepared by powder injection molding (PIM) and supersolidus liquid-phase sintering from powder prepared by a plasma rotating-electrode process, and the nitrogen content and relative density of the sintered parts were 0.37% and 97.9%, respectively. The densification and nitrogen content of sintered parts at different sintering temperatures in a nitrogen atmosphere were studied. The results indicate that the relative density increased gradually, whereas the nitrogen content of the sintered parts decreased gradually with increasing sintering temperature under the nitrogen pressure of 0.2 bar. The parts sintered at 1400 °C for 1.5 h exhibited ideal sintering relative density and nitrogen content. After solution treatment at 1150 °C for 1 h, the ratio of ferrite to austenite was approximately 46.8:51.8; the measured tensile strength, the yield strength, the elongation and the hardness were 761 MPa, 529 MPa, 14%, and 321.4 HV, respectively. The samples prepared by PIM can achieve full densification followed by hot isostatic pressing and solution treatment, and its tensile strength and elongation are significantly improved, which is better than that of casting. This study provides a new method for the preparation of high-nitrogen-content HDSS with a complex shape and controllable nitrogen content by near-net shaping.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Corrosion Behavior and Inhibition · High Temperature Alloys and Creep
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (26)
Show source-provided references
1. Development and trend of hyper duplex stainless steels
2. Development of Chinese duplex stainless steel in recent years10.1016/S1006-706X(17)30018-3 ↗
3. Welding duplex stainless steels — a review of current recommendations10.1007/BF03321380 ↗
4. Investigation of the sensitization and intergranular corrosion of tube-to-tubesheet welds of hyper duplex stainless steel using an electrochemical reactivation method10.1016/j.corsci.2014.06.005 ↗
5. Fracture toughness of a welded super duplex stainless steel10.1016/j.msea.2014.03.049 ↗
6. Influence of the shielding gas composition on the passive film and erosion corrosion of tube-to-tube sheet welds of hyper duplex stainless steel10.1016/j.corsci.2014.11.014 ↗
7. X. J. Yuan, C. Y. Kang, Microstructural Characteristics in Vacuum TLP (Transient Liquid.
8. Phase) bonds using a novel iron-based interlayer based on duplex stainless steel base metal alloyed with a melting-point depressant10.1016/j.vacuum.2013.04.025 ↗
9. Investigation on the thermostability of residual stress and microstructure in shot peened SAF 2507 duplex stainless steel10.1016/j.vacuum.2018.04.015 ↗
10. Effects of different thermoplastic wax-based binders on properties of 316L stainless steel injection molding parts10.1016/S1875-5372(18)30005-5 ↗
11. Structure and properties of steel produced by metal injection molding10.1134/S2075113317020162 ↗
12. Powder injection molding of biocompatible stainless steel biodevices10.1016/j.powtec.2016.03.039 ↗
13. Investigation of boron addition on densification and cytotoxicity of powder injection molded 316L stainless steel dental materials10.1007/s13369-016-2224-1 ↗
14. Debinding rate enhancement of 17-4 precipitation hardening stainless steel solvent debinding on metal injection molding process as the material for orthodontic bracket10.4028/www.scientific.net/MSF.929.200 ↗
15. Microstructure and mechanical properties of 17-4PH steel and Fe-Cr-B alloy mixed material manufactured using powder injection molding10.3365/KJMM.2018.56.5.342 ↗
16. Vacuum sintering process in metal injection molding for 17-4 PH stainless steel as material for orthodontic bracket10.4028/www.scientific.net/SSP.266.231 ↗
17. Investigation of powder size effects on sintering of powder injection moulded 17-4PH stainless steel10.1080/00325899.2017.1278911 ↗
18. Development of 17-4PH stainless steel bimodal powder injection molding feedstock with the help of interparticle spacing/lubricating liquid concept10.1016/j.powtec.2015.05.013 ↗
19. S. J. Kim, S. N. Bae, J. H. Kim, C. T. Kim, K. T. Han, J. M. Lee, J. K. Jung, H. Wohlfromm, P. J. Uggowitzer, P.A.N.A.C E.A. provides the answer to Ni Allergy, Met. Powder Rep., 53 (1998) 48-52. https://doi.org/10.1016/s0026-0657(98)80010-6.10.1016/S0026-0657(98)80010-6 ↗
20. Sintering optimisation and solution annealing of high nitrogen nickel free austenitic stainless steels prepared by PIM10.1179/174329008X284930 ↗
21. Duplex stainless steel self-ligatingOrthodontic brackets by micro-powder injection moulding
22. Microstructural study of duplex stainless steels obtained by powder injection molding10.1016/j.jallcom.2013.11.144 ↗
23. Powders, binders and feedstocks for powder injection molding
24. The microstructure, mechanical properties, and corrosion resistance of UNS S32707 hyper-duplex stainless steel processed by selective laser melting10.3390/met9091012 ↗
25. Novel ferritic stainless steel with advanced mechanical properties and significant magnetic responses processed by selective laser melting10.2320/matertrans.M2018374 ↗
26. Post-sintering thermal treatment of nitrogen containing pressed and sintered and PIM stainless steels10.1179/174329007X164853 ↗