journal article·2018-06

A study on chip and microstructure of 7055 aluminum alloy's 3D HSC based on FEM and experiment

Ping Zhang, Youqiang Wang

Vacuum· Volume 152
Publisher page

Abstract

Abstract In this paper,a 3D high speed cutting model is then built, and finite-element analysis is carried out based on DEFORM-3D and the J-C constitutive equation satisfying the “three-high features”. Simulation results show that the chip temperature has obvious positive correlation with the cutting speed: the greater the cutting speed is, the higher the chip temperature gets. The cutting speed show obvious positive correlation with the wearing depth of tool at a steady state during cutting; the greater the cutting speed is, the greater the wearing depth of tool gets, and the greater the change rate of wearing depth gets. The cutting speed show obvious negative correlation with the wearing depth of tool at a steady state during cutting; the greater the cutting speed is, the smaller the wearing depth of tool gets. The average grain size is negatively correlated with the cutting speed. When the cutting speed is at 50 m/min and 100 m/min, there is no obvious dynamic recrystallization; when the cutting speed is at 150 m/min, dynamic recrystallization occurs. When the cutting speed is 100 m/min, there are dislocation walls in the center of the specimen, and there is dynamic recrystallization grain in the dislocation wall. Cube, Goss, {023} (2.5°, 35°, 0°) and {032} (2.5°, 55°, 0°) textures exist under all cutting speeds with cube texture prevailing over the other three forms. When the cutting speed increases to 150 m/min, in addition to all the forms of texture present under the cutting speed of 50 m/min, small amounts of, though fairly weak, {212} (82°, 47°, 65°), {210} (90°, 87°, 65°), {213} (145°, 40°, 65°) and E are also detected, displaying a discrete texture distribution.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Metallurgy and Material Forming · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (16)

Show source-provided references
1. Dynamic recrystallization of 7055 aluminum alloy during hot deformation10.4028/www.scientific.net/MSF.650.295 ↗
2. Experimental investigation on 3d chip morphology properties of rotary surface during orthogonal turn-milling of aluminum alloy
3. Influence of second-phase particles on chip breakability in aluminum alloys10.2464/jilm.56.699 ↗
4. Production of wire via friction extrusion of aluminum alloy machining chips10.1016/j.jmatprotec.2010.08.010 ↗
5. Simulation on cutting temperature during high-speed milling aluminum alloy 705510.4028/www.scientific.net/AMM.328.486 ↗
6. A study on the different finite element approaches for laser cutting of aluminum alloy sheet
7. Finite element simulation study of cutting process for large thin-wall part of aluminum alloy10.4028/www.scientific.net/KEM.522.62 ↗
8. Study on numerical modeling of three dimensional oblique cutting for aluminum alloy cutting process10.4028/www.scientific.net/AMM.37-38.1316 ↗
9. Influence of element types on springback prediction of creep age forming of aluminum alloy integral panel10.4028/www.scientific.net/MSF.773-774.512 ↗
10. Control rules of surface integrity and formation of metamorphic layer in high-speed milling of 7055 aluminum alloy10.1177/0954405414527268 ↗
11. Observations of the tool–chip boundary conditions in turning of aluminum alloys10.1016/j.wear.2006.08.019 ↗
12. Analysis of chip breaking prediction in cutting aluminum alloys10.4028/www.scientific.net/MSF.532-533.213 ↗
13. Research on cutting force of milling aviation aluminum alloy10.4028/www.scientific.net/AMR.299-300.1032 ↗
14. Experimental study on cutting force and surface roughness for 7050-t7451 aluminum alloy of high speed milling10.4028/www.scientific.net/AMM.395-396.1026 ↗
15. The research on cutting force in high-speed milling process of aluminum alloy impeller10.4028/www.scientific.net/AMR.142.11 ↗
16. Effect of deformation induced precipitation on grain refinement and improvement of mechanical properties aa 7055 aluminum alloy