journal article·2018-02

An improved braking control method for the magnetically levitated TMP with a fast transient response

Kun Mao, Gang Liu

Vacuum· Volume 148
Publisher page

Abstract

Abstract In the vacuum application based on the turbo-molecular pump (TMP), the pump rotor has to be stopped completely to prevent the blade from the air impact before trapping air into the vacuum chamber. However, due to the vacuum environment and high speed, the TMP braking process lasts much longer than that of the high-speed rotating machinery in the air. Particularly, the active magnetic bearings, which have been widely used in the TMP, eliminate the bearing friction resistance. In this case, the traditional electric braking method based on a non-controllable rectification cannot stop the rotor efficiently. Hence, a novel braking control method for the magnetically levitated TMP with a fast transient is proposed. When the TMP runs at high speed, it works like the traditional braking method, but with a temperature close-loop control, which is used to prevent the stator from overheat with the maximum current. Meanwhile, in the low speed range, the power switches of the inverter are controlled specifically to increase the DC-bus voltage. Thererfore, the barking current could be remained at a high level to reduce the braking time. At last, the proposed braking method is verified on a magnetically levitated TMP with 4100L/s pumping speed.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Hydraulic and Pneumatic Systems · Refrigeration and Air Conditioning Technologies · Plasma Diagnostics and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (18)

Show source-provided references
1. Schweitzer · 2009
2. Application of the magnetic suspension technique in vacuum and surface physics10.1016/0042-207X(90)90110-K ↗
3. Huang · 2016 · vol. 142 · 96
4. Modeling method of the modal analysis for turbomolecular pump rotor blades10.1016/j.vacuum.2017.07.029 ↗
5. Multi-objective optimization design of a high-speed PM machine supported by magnetic bearings10.1016/j.ymssp.2017.01.013 ↗
6. Design and implementation of a fault-tolerant magnetic bearing system for turbo-molecular vacuum pump10.1109/TMECH.2005.859830 ↗
7. Design of a sensorless commutation ic for bldc motors10.1109/TPEL.2003.818867 ↗
8. Sensorless control of bldcm drive for a high-speed maglev blower using low-pass filter10.1109/TPEL.2016.2645782 ↗
9. Industry application of zero-speed sensorless control techniques for pm synchronous motors10.1109/28.913716 ↗
10. A high-speed sliding-mode observer for the sensorless speed control of a pmsm10.1109/TIE.2010.2098357 ↗
11. Adaptive compensation method for high-speed surface pmsm sensorless drives of emf-based position estimation error
12. A novel regenerative braking method of bldcm for wheeled mobile robot
13. A cost-effective method of electric brake with energy regeneration for electric vehicles10.1109/TIE.2009.2015356 ↗
14. An efficient regenerative braking system based on battery/supercapacitor for electric, hybrid, and plug-in hybrid electric vehicles with BLDC motor
15. Ultracapacitors + dc–dc converters in regenerative braking system10.1109/MAES.2002.1028079 ↗
16. Energy-management system for a hybrid electric vehicle, using ultracapacitors and neural networks10.1109/TIE.2006.870880 ↗
17. New DC–DC converter for energy storage system interfacing in fuel cell hybrid electric vehicles10.1109/TPEL.2006.886650 ↗
18. Operation of a six-phase induction machine using series-connected machine-side converters10.1109/TIE.2013.2248338 ↗