Scanning velocity influence on microstructure evolution and mechanical properties of laser melting deposited 12CrNi2 low alloy steel
Source abstract
Abstract
Abstract 12CrNi2 low alloy steels were prepared by laser melting deposition (LMD), aiming at investigating the effect of laser scanning velocity on phase composition, microstructure, microhardness, residual stress and tensile properties of the specimens. Experimental results showed that the α-Fe diffraction peaks in the specimens shifted to lower angle due to the solid solution of ferrite-forming elements. The microstructure of LMD-processed 12CrNi2 alloy steel was mainly composed of ferrite (F) and granular bainite (GB). High microhardness (348 ± 8 HV0.2) and low residual tensile stress (57 ± 5 Mpa) can be achieved by optimizing the laser parameters. As the laser scanning velocity increased, the average granular size was refined and the majority of grains had smaller sizes close to 2–3 μm, which was significantly finer compared with those prepared by conventional process. LMD-processed 12CrNi2 alloy steel exhibited satisfactory mechanical properties with ultimate tensile strength (1000 ± 17 MPa), yield strength (960 ± 12 MPa) and higher elongation (10.02%), which could reach the requirements of low alloy steel components due to the satisfactory strength and toughness.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Welding Techniques and Residual Stresses · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (53)
Show source-provided references
1. Effect of Ni content on stainless steel fabricated by laser melting deposition10.1016/j.optlastec.2017.11.032 ↗
2. Predictive modeling of solidification during laser additive manufacturing of nickel superalloys: recent developments, future directions10.1088/2053-1591/aaa04c ↗
3. Investigation of laser metal deposited Alloy 718 onto an EN 1.4401 stainless steel substrate10.1016/j.optlastec.2017.05.038 ↗
4. Energy consumption and saving analysis for laser engineered net shaping of metal powders10.3390/en9100763 ↗
5. The impact of powder oxygen content on formability of 12CrNi2 alloy steel fabricated by laser melting deposition10.1080/00325899.2019.1616367 ↗
6. Study on microstructure, mechanical properties and machinability of efficiently additive manufactured AISI 316L stainless steel by high-power direct laser deposition10.1016/j.jmatprotec.2016.09.005 ↗
7. Influences of pulse laser parameters on properties of AISI316L stainless steel thin-walled part by laser material deposition10.1016/j.optlastec.2016.12.021 ↗
8. Mechanical properties and microstructural features of direct laser-deposited Ti-6Al-4V10.1007/s11837-015-1308-9 ↗
9. A 3D dynamic numerical approach for temperature and thermal stress distributions in multilayer laser solid freeform fabrication process10.1016/j.optlaseng.2007.06.010 ↗
10. Experimental investigation on selective laser melting of 17-4PH stainless steel10.1016/j.optlastec.2016.07.012 ↗
11. Effects of HIP and post heat treatment on the microstructures and properties of laser direct deposited 12CrNi2 steels
12. Numerical and experimental investigation into the subsequent thermal cycling during selective laser melting of multi-layer 316L stainless steel10.1016/j.optlastec.2017.07.034 ↗
13. Effect of heat input on cracking in laser solid formed DZ4125 superalloy10.1016/j.optlastec.2016.06.008 ↗
14. Microstructure and mechanical property of 12CrNi2 high strength steel fabricated by laser additive manufacturing technology10.1088/1757-899X/423/1/012077 ↗
15. Effects of substrate preheating temperatures on the microstructure, properties, and residual stress of 12CrNi2 prepared by laser cladding deposition technique10.3390/ma11122401 ↗
16. Heat-induced molten pool boundary softening behavior and its effect on tensile properties of laser additive manufactured aluminum alloy10.1016/j.vacuum.2018.05.030 ↗
17. Laser surface alloying of FeCoCrAlNi high-entropy alloy on 304 stainless steel to enhance corrosion and cavitation erosion resistance
18. Phase evolution and wear resistance of in situ synthesized V8C7 particles reinforced Fe-based coating by laser cladding10.1016/j.optlastec.2018.02.019 ↗
19. Microstructures and mechanical properties of CrMnFeCoNi high entropy alloys fabricated using laser metal deposition technique10.1016/j.jallcom.2018.09.235 ↗
20. Customizing mechanical properties of additively manufactured Hastelloy X parts by adjusting laser scanning speed10.1016/j.jallcom.2019.152097 ↗
21. Scanning speed influence on the microstructure and micro hardness properties of Titanium alloy produced by laser metal deposition process10.1016/j.matpr.2017.05.028 ↗
22. Effect of processing parameters on microstructure and tensile properties of austenitic stainless steel 304L made by directed energy deposition additive manufacturing10.1016/j.actamat.2016.03.019 ↗
23. Microstructure evolution and EBSD analysis of a graded steel fabricated by laser additive manufacturing10.1016/j.vacuum.2017.03.021 ↗
24. Effect of Cr3C2 content on 316L stainless steel fabricated by laser melting deposition10.1016/j.vacuum.2017.10.027 ↗
25. In situ synthesis of TiC reinforced surface MMC on Al6061 by laser surface alloying10.1016/S1359-6462(01)01230-1 ↗
26. Preparation and characterization of in situ carbide particle reinforced Fe-based gradient materials by laser melt deposition10.3390/coatings9080467 ↗
27. Understanding the effect of laser scan strategy on residual stress in selective laser melting through thermo-mechanical simulation
28. Design, preparation, microstructure and properties of novel wear-resistant stainless steel-base composites using laser melting deposition10.1016/j.vacuum.2019.04.016 ↗
29. Selective laser melting of 24CrNiMo steel for brake disc: fabrication efficiency, microstructure evolution, and properties10.1016/j.optlastec.2018.05.033 ↗
30. Effects of chromium addition on microstructure and properties of TiC-VC reinforced Fe-based laser cladding coatings10.1016/j.jallcom.2014.06.073 ↗
31. Effects of processing parameters on consolidation and microstructure of W-Cu components by DMLS10.1016/j.jallcom.2008.05.065 ↗
32. Effects of laser sintering processing parameters on the microstructure and densification of iron powder10.1016/S0921-5093(03)00341-1 ↗
33. Formation mechanism and phase evolution of in situ synthesizing TiC-reinforced 316L stainless steel matrix composites by laser melting deposition10.1016/j.matlet.2018.01.097 ↗
34. Functionally graded stainless steel fabricated by direct laser deposition: anisotropy of mechanical properties and hardness10.1007/s40195-017-0668-2 ↗
35. Dissolution kinetics of delta ferrite in AISI 304 stainless steel produced by strip casting process10.1016/S0921-5093(03)00152-7 ↗
36. TEM observation of dynamic distortion in 2Y-PSZ/steel composites10.1016/S0272-8842(03)00065-8 ↗
37. Microstructural refinement of weld fusion zones in α-β titanium alloys using pulsed current welding10.1016/S0921-5093(98)01010-7 ↗
38. Microstructure and properties of laser-deposited Ti6Al4V metal matrix composites using Ni-coated powder10.1007/s11661-008-9498-1 ↗
39. Layer thickness dependence of performance in high-power selective laser melting of 1Cr18Ni9Ti stainless steel10.1016/j.jmatprotec.2014.07.034 ↗
40. The evolution of bainite and mechanical properties of direct laser deposition 12CrNi2 alloy steel at different laser power10.1016/j.msea.2018.10.092 ↗
41. The role of niobium in improving toughness and corrosion resistance of high speed steel laser hardfacings10.1016/j.matdes.2016.03.081 ↗
42. Laser cladding in-situ NbC particle reinforced Fe-based composite coatings with rare earth oxide addition10.1016/j.surfcoat.2013.11.026 ↗
43. Residual stresses in selective laser sintering and selective laser melting10.1108/13552540610707013 ↗
44. Residual stress within metallic model made by selective laser melting process10.1016/S0007-8506(07)60677-5 ↗
45. Microstructure and mechanical properties of laser solid formed 300M steel10.1016/j.jallcom.2014.09.111 ↗
46. Effect of laser incident energy on microstructures and mechanical properties of 12CrNi2Y alloy steel by direct laser deposition10.1016/j.jmst.2018.10.024 ↗
47. A high strength low alloy steel fabricated by direct laser deposition10.1016/j.vacuum.2018.12.030 ↗
48. Effects of Y and Ti addition on microstructure stability and tensile properties of reduced activation ferritic/martensitic steel10.1016/j.net.2019.03.001 ↗
49. Angular distortive matrices of phase transitions in the fcc-bcc-hcp system10.1016/j.actamat.2016.01.075 ↗
50. Effects of substrate preheating on the thin-wall part built by laser metal deposition shaping10.1016/j.apsusc.2014.08.113 ↗
51. Microstructure and mechanical behavior of additive manufactured Cr-Ni-V low alloy steel in different heat treatment10.1016/j.vacuum.2020.109216 ↗
52. Microstructure and tensile properties of laser melting deposited Ti-5Al-5Mo-5V-1Cr-1Fe near β titanium alloy10.1016/j.msea.2013.08.032 ↗
53. Microstructure and fatigue behavior of a laser additive manufactured 12CrNi2 low alloy steel10.1016/j.msea.2019.138685 ↗