journal article·2017-12

Research of the bonded interface of Cu9Al4Fe/1Cr18Ni9Ti stainless steel bimetallic composite

Juntao Zou, Silin Li, Yanni Wei, Shuhua Liang

Vacuum· Volume 146
Publisher page

Abstract

Abstract Cu9Al4Fe/1Cr18Ni9Ti stainless steel bimetallic composite was prepared by the method of vacuum casting. The microstructure morphology, mechanism bonding and mechanical property of Cu9Al4Fe/1Cr18Ni9Ti bimetallic composite were observed by scanning electron microscope, energy disperse spectroscopy, X-ray diffraction, transmission electron microscope and nano-indentation analysis techniques respectively. The research results are as follows: The interface transition layer of Cu9Al4Fe/1Cr18Ni9Ti bimetallic composite maintains straight and a certain thickness and no obvious defects are observed. The phase on the transition zone is consisted of α-Fe based solid solution, γ-Fe based solid solution, NiAl phase and AlCr2 phase. The micro-hardness and elastic modulus of the interface transition layer are higher than the two matrix alloys. The fracture of Cu9Al4Fe/1Cr18Ni9Ti bimetallic composite prefers to occur between 1Cr18Ni9Ti and the interface transition layer, and the fracture mode is cleavage fracture.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (21)

Show source-provided references
1. Interfacial characterization of SLM parts in multi-material processing: metallurgical diffusion between 316L stainless steel and C18400 copper alloy10.1016/j.matchar.2014.05.001 ↗
2. Effect of beam offset on the characteristics of copper and304 stainless steel electron beam welding10.1016/j.vacuum.2016.03.034 ↗
3. Influence of interface microstructure on the mechanical properties of titanium/17-4PH stainless steel solid state diffusion bonded joints10.1016/j.matdes.2011.10.041 ↗
4. Interface microstructure and strength properties of diffusion bonded joints of titanium-Al interlayer-18Cr-8Ni stainless steel10.1016/j.msea.2009.12.042 ↗
5. On the Al/Cu dissimilar joints produced through simple cold compression
6. Interfacial microstructure and properties of copper clad steel produced using friction stir welding versus gas metal arc welding10.1016/j.matchar.2015.02.022 ↗
7. Fiber laser welding of austenitic steel and commercially pure copper butt joint10.1016/j.optlaseng.2016.10.008 ↗
8. Study on welding–brazing of copper and stainless steel using tungsten/metal gas suspended arc welding10.1016/j.matlet.2015.04.128 ↗
9. Influence of processing parameters on the characteristics of stainless steel/copper laser welding10.1016/j.jmatprotec.2015.03.003 ↗
10. Investigation on microstructures and properties of arc-sprayed-Al/AZ91D bimetallic material by solid–liquid compound casting10.1016/j.matdes.2016.09.085 ↗
11. Interfacial characteristics of diamond/aluminum composites with high thermal conductivity fabricated by squeeze-casting method10.1016/j.matchar.2015.06.023 ↗
12. Effect of surface nitriding treatment in a steel plate on the interfacial bonding strength of the aluminum/steel clad sheets by the cold roll bonding process10.1016/j.msea.2016.11.051 ↗
13. Interfacial microstructure of Al-Sn-Pb Alloy/Steel during liquid-solid bonding rolling10.1016/S1006-706X(06)60075-7 ↗
14. Joining Ti3SiC2 MAX phase with 308 stainless steel and aluminum fillers by tungsten inert gas (TIG)-brazing process10.1016/j.ceramint.2015.09.026 ↗
15. Effects of zinc coating on interfacial microstructures and mechanical properties of aluminum/steel bimetallic composites10.1016/j.jallcom.2016.03.276 ↗
16. Study on the effect of post-annealing on the microstructural evolutions and mechanical properties of rolled CGPed Aluminum-Manganese-Silicon alloy10.1016/j.msea.2016.10.054 ↗
17. Constrained groove pressing and subsequent annealing of Al-Mn-Si alloy: microstructure evolutions, crystallographic transformations, mechanical properties, electrical conductivity and corrosion resistance10.1016/j.matdes.2017.03.053 ↗
18. Microstructure and properties of the Ti(C,N)–xMo2C–Ni cermet/steel joint by a novel diffusion bonding method10.1016/j.matchar.2014.11.022 ↗
19. Microanalysis of crystallographic characteristics and structural transformations in SPDed AleMneSi alloy by dual-straining10.1016/j.jallcom.2016.12.086 ↗
20. Study on the post-rolling direction of severely plastic deformed Aluminum-Manganese-Silicon alloy10.1016/j.acme.2016.06.005 ↗
21. First-principles investigations on the crystal, electronic structure and mechanical properties of AlCr2 compound at varying pressures10.1016/j.commatsci.2012.04.025 ↗