Investigation on microstructure and properties of Al18B4O33 whisker reinforced Al Mg Si matrix composite after shot peening
Source abstract
Abstract
Abstract This work investigated the influences of two-step shot peening on the residual stress fields, microstructure, microhardness and corrosion performance of aluminum borate (Al18B4O33) whisker reinforced Al Mg Si matrix composite by X-ray stress tester, X-ray diffraction line profile analysis method, transmission electron microscopy (TEM), Vickers analyzer and electrochemical examinations, respectively. The results indicate that shot peening induces considerable compressive residual stress (−151 MPa) and satisfied microstructure refinement into the near surface region. The domain sizes gradually increase from the top surface to the substrate, the microstrain and dislocation density present the contrary variation trends. The maximum microhardness locates at top surface and the value is about 2.5 times that of matrix. Furthermore, shot peening improves the corrosion performance of Al18B4O33 whisker reinforced Al Mg Si matrix composite. The sample with a peening intensity 0.40 + 0.08 mmN possesses the best corrosion behavior with maximum polarization resistance (15133 Ω cm2) and lowest corrosion current density (2.202 μA cm−2). The refined domain size and compressive residual stress should account for the improvement of corrosion behavior. However, further increasing shot peening intensity, the corrosion resistance drops, which is considered as a consequence of induced surface defects, increased surface roughness and dislocation density.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Surface Treatment and Residual Stress · High-Velocity Impact and Material Behavior · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (44)
Show source-provided references
1. Effect of reinforcement particle size and weight fraction on the mechanical properties of SiC particle reinforced Al metal matrix composites
2. Metal matrix composites reinforced by nano-particles—a review
3. Thermal expansion and thermal mismatch stress relaxation behaviors of SiC whisker reinforced aluminum composite10.1016/S0254-0584(02)00172-4 ↗
4. Champaigne · 2001
5. Microstructural characterisation of metallic shot peened and laser shock peened Ti–6Al–4V10.1016/j.actamat.2016.10.044 ↗
6. Effect of pitting corrosion on fatigue performance of shot-peened aluminium alloy 7075-T65110.1016/j.jmatprotec.2010.03.004 ↗
7. Enhancement of fatigue and corrosion properties of pure Ti by sandblasting10.1016/j.msea.2006.04.024 ↗
8. Influence of surface modifications on pitting corrosion behavior of nickel-base alloy 718. Part 1: effect of machine hammer peening10.1016/j.corsci.2013.08.007 ↗
9. The effect of shot peening on fatigue and corrosion behavior of 316L stainless steel in Ringer's solution10.1016/j.surfcoat.2010.04.015 ↗
10. Effects of surface treatments on high cycle corrosion fatigue of metallic implant materials10.1016/S0142-1123(00)00057-8 ↗
11. Effect of micro shot peening on the mechanical properties and corrosion behavior of two microstructure Ti–6Al–4V alloy10.1016/j.apsusc.2015.12.019 ↗
12. Effect of shot peening and plasma electrolytic oxidation on the intergranular corrosion behavior of 7A85 aluminum alloy10.1007/s40195-014-0104-9 ↗
13. Aluminium composites reinforced with a new aluminium borate whisker10.1007/BF00721787 ↗
14. Fatigue behavior of Al18B4O33 whisker-framework reinforced Al matrix composites at high temperatures10.1016/S0266-3538(02)00208-7 ↗
15. Quantification of dislocations densities in zirconium hydride by X-ray line profile analysis10.1016/j.actamat.2016.06.058 ↗
16. Investigation on the thermostability of residual stress and microstructure in shot peened SAF 2507 duplex stainless steel10.1016/j.vacuum.2018.04.015 ↗
17. Use of the Voigt function in a single-line method for the analysis of X-ray diffraction line broadening10.1107/S0021889882012035 ↗
18. Dislocation densities in some annealed and cold-worked metals from measurements on the X-ray debye-scherrer spectrum10.1080/14786435608238074 ↗
19. Influence of peening on the corrosion properties of AISI 304 stainless steel10.1016/j.corsci.2009.08.008 ↗
20. The influence of peening conditions on the resulting distribution of residual stress
21. Mechanism of creation of compressive residual stress by shot peening10.1016/S0142-1123(98)00002-4 ↗
22. Residual stress and microstructure of the CNT/6061 composite after shot peening10.1016/j.matdes.2016.06.030 ↗
23. R. Yang, et al., Effect of shot peening on the residual stress and mechanical behaviour of low-temperature and high-temperature annealed martensitic gear steel 18CrNiMo7-6, 219 (2017) 012046.
24. Stacking fault energies and slip in nanocrystalline metals10.1038/nmat1136 ↗
25. Structure, microhardness and damping characteristics of Al matrix composite reinforced with AlCuFe or Ti using ultrasonic impact peening10.1016/j.surfcoat.2009.10.009 ↗
26. Microstructure and evolution of mechanically-induced ultrafine grain in surface layer of AL-alloy subjected to USSP10.1016/S1359-6454(02)00051-4 ↗
27. Microstructural change of ultrafine-grained aluminum during high-speed plastic deformation10.1016/S0921-5093(02)00709-8 ↗
28. Microstructure of two-phase Al–1.7 at% Cu alloy deformed by equal-channel angular pressing10.1016/S1359-6454(00)00308-6 ↗
29. Structure, microhardness and damping characteristics of Al matrix composite reinforced with AlCuFe or Ti using ultrasonic impact peening10.1016/j.surfcoat.2009.10.009 ↗
30. Toward a quantitative understanding of mechanical behavior of nanocrystalline metals10.1016/j.actamat.2007.01.038 ↗
31. Investigation on surface layer characteristics of shot peened graphene reinforced Al composite by X-ray diffraction method10.1016/j.apsusc.2017.11.242 ↗
32. Investigation on the residual stress and microstructure of (TiB + TiC)/Ti–6Al–4V composite after shot peening10.1016/j.msea.2011.01.022 ↗
33. Hall–Petch and dislocation strengthening in graded nanostructured steel10.1016/j.actamat.2012.07.037 ↗
34. The effect of surface contamination on corrosion performance of ultrasonic shot peened 7150 Al alloy10.1016/j.surfcoat.2017.08.028 ↗
35. Fabrication and corrosion performances of pure Ni and Ni-based coatings containing rare earth element Ce and graphene by reverse pulse electrodeposition10.1149/2.1261702jes ↗
36. Electrochemical corrosion behavior of Al18B4O33w/Al composite[J]10.1007/s10853-005-4404-3 ↗
37. Evaluation of corrosion resistance of AA6082-T651 aluminium alloy after laser shock peening by means of cyclic polarisation and ElS methods10.1016/j.corsci.2012.03.019 ↗
38. Influence of ultrasonic shot peening on corrosion behavior of 7075 aluminum alloy10.1016/j.jallcom.2017.06.310 ↗
39. Effects of laser peening on stress corrosion cracking (SCC) of ANSI 304 austenitic stainless steel10.1016/j.corsci.2012.03.044 ↗
40. The improvement of the corrosion resistance of 309 stainless steel in the transpassive region by nano-crystallization10.1016/j.electacta.2008.08.073 ↗
41. On the chloride-induced pitting of ultra fine grains 5052 aluminum alloy produced by accumulative roll bonding process10.1016/j.jallcom.2011.01.066 ↗
42. Effects of nanofeatures induced by severe shot peening (SSP) on mechanical, corrosion and cytocompatibility properties of magnesium alloy AZ3110.1016/j.actbio.2017.11.032 ↗
43. Estimation of microstructure and corrosion properties of peened nickel aluminum bronze10.1016/j.surfcoat.2017.01.073 ↗
44. Surface severe plastic deformation of AISI 304 via conventional shot peening, severe shot peening and repeening10.1016/j.apsusc.2015.05.093 ↗