Properties of BaTiO3–Al2O3 composite oxide films prepared by sol-gel coating and anodization
Source abstract
Abstract
Abstract High-voltage etched aluminum foils were coated with BaTiO3 (BT) films by vacuum infiltration using a sol. The specimens coated with the BT films were annealed at 450–550 °C for 10–90 min, and this procedure was repeated several times (n = 0, 1, 2, 4, and 8 cycles), after which the specimens were finally anodized at 100–500 V. The BT films coated on the high-voltage etched aluminum foils were crystallized when annealed at 550 °C for 30 min. The thickness of the BT-coated layer decreased after the anodization, proving that the BT-coated layers were decomposed by the anodization, likely contributing to the formation of a BT–Al2O3 (BT–Al) composite oxide layer between the inner BT-coated layer and the outer Al2O3 layer. The maximum specific capacitance (CS) of the specimens was obtained after 4 cycles of BT coating. The specific capacitances of the BT-coated specimens were higher than those of the specimens without the BT-film coating. The withstanding voltages of the specimens were approximately 123, 330, and 545 V when the specimens were anodized at 100, 300, and 500 V, respectively. These results suggest the successful fabrication of BT–Al composite oxide films on high-voltage etched aluminum foils.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Ferroelectric and Piezoelectric Materials · Semiconductor materials and devices · Anodic Oxide Films and Nanostructures
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (24)
Show source-provided references
1. Effects of polymer corrosion inhibitor on widening etch tunnels of aluminum foil for capacitor10.1016/j.corsci.2013.07.011 ↗
2. Formation of Al/(Ti, Nb, Ta)–composite oxide films on aluminum by pore filling10.1149/1.1837892 ↗
3. Electron microscopic study of anodic oxide films formed on aluminum with thermal oxidation
4. Anodizing properties of high dielectric oxide films coated on aluminum by sol-gel method10.1007/s10832-004-5085-z ↗
5. Preparation of titanium dioxide films on etched aluminum foil by vacuum infiltration and anodizing10.1016/j.apsusc.2016.01.166 ↗
6. The effect of anodizing voltage on the electrical properties of Al–Ti composite oxide film on aluminum10.1016/j.jelechem.2006.02.016 ↗
7. Formation behavior of multi-layer oxide films on etched Al foil by vacuum infiltration and anodization10.1149/2.0051508jss ↗
8. Formation of Al–Zr composite oxide films on aluminum by sol-gel coating and anodizing10.1016/S0022-0728(99)00121-7 ↗
9. Dielectric properties of Al–Si composite oxide films formed on electropolished and DC-etched aluminum by electrophoretic sol-gel coating and anodizing10.1007/s10008-007-0316-2 ↗
10. Formation of Al2O3–BaTiO3 composite thin film to increase the specific capacitance of aluminum electrolytic capacitor10.1016/j.tsf.2008.04.077 ↗
11. Thickness limit of BaTiO3 thin film capacitors grown on SUS substrates using aerosol deposition method10.1016/j.tsf.2010.03.159 ↗
12. Molecular beam epitaxy growth of BaTiO3 thin films and crucial impact of oxygen content conditions on the electrical characteristics10.1016/j.tsf.2011.10.182 ↗
13. Al2O3–TiO2 composite oxide films on etched aluminum foil by hydrolysis precipitation and anodizing10.1007/s10853-005-2507-5 ↗
14. Electrophoresis deposition of TiO2 nanoparticles on etched aluminum foil for enhanced specific capacitance10.1149/2.013201esl ↗
15. (Ba0.5Sr0.5)TiO3 modification on etched aluminum foil for electrolytic capacitor10.1016/j.ceramint.2007.03.004 ↗
16. Formation of Al2O3–BaTiO3 nanocomposite oxide films on etched aluminum foil by sol–gel coating and anodizing10.1007/s10971-007-1619-6 ↗
17. Wet routes of high purity BaTiO3 nanopowders10.1016/j.jallcom.2006.09.023 ↗
18. Effect of mechanical milling on solid state formation of BaTiO3 from BaCO3–TiO2 (rutile) mixtures10.1016/S0040-6031(01)00505-6 ↗
19. Effect of technological parameters on specific capacitance of Al–Ti composite oxide films
20. Cross-sections of hydrous and composite aluminum oxide films10.1016/0013-4686(78)80072-3 ↗
21. Alkaline corrosion-resistance of aluminum anodic oxide film-coated with zirconium-oxide by a sol-gel process10.2320/jinstmet1952.59.5_547 ↗
22. Influence of γ-alumina on the structure of barrier anodic oxide films on aluminum10.1149/1.2095826 ↗
23. Effect of heat-treatment on characteristics of anodized aluminum oxide formed in ammonium adipate solution10.1149/1.1646140 ↗
24. Effect of TiO2 nanostructures on specific capacitance of Al2O3–TiO2 composite film on etched aluminum foil formed by the sol-gel and anodizing10.1016/j.ceramint.2013.09.056 ↗