Formation of sol-gel based Cu 2 ZnSnS 4 thin films using ppm-level hydrogen sulfide
Source abstract
Abstract
Abstract This study reports the preparation of copper zinc tin sulfide (Cu2ZnSnS4 or CZTS) thin films using parts-per-million (ppm) level of hydrogen sulfide (H2S) gas as opposed to high percentage level of H2S (e.g., ≥ 5%) in many other studies. Sol-gel technique was adopted for the preparation of metal oxide films from precursor solutions with different ratios of Cu, Zn, and Sn metal ions. Sulfurization process was carried out in tube furnace using 100 ppm H2S balanced by hydrogen at different temperatures. Generally, it was observed that the sulfur content of the thin films obtained showed strong dependence on the sulfurization temperature. Samples sulfurized at higher temperatures (e.g., ~ 450 and 550 °C) in ppm-level H2S experienced significant sulfur loss as confirmed by EDS, which was accompanied by the formation of metal alloys such as Cu3Sn as identified by XRD. On the other hand, samples sulfurized at lower temperatures of ~ 350 °C and even 125 °C revealed the formation of CZTS phase as confirmed by XRD, Raman micro-spectroscopy, and sheet resistance measurement. Moreover, local EDS analysis indicates that CZTS films prepared at those low temperatures have near-stoichiometric composition and are sometimes accompanied by the formation of Cu2 − xS phase(s). In addition, stoichiometric and Cu-rich precursor solutions tend to yield CZTS samples with better crystallinity and superior optical properties compared with the Cu-deficient solution. These results are discussed from thermodynamics perspective and the directions for future research for safer and more economical processing of CZTS solar cells are pointed out.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Chalcogenide Semiconductor Thin Films · Quantum Dots Synthesis And Properties · Copper-based nanomaterials and applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. Routes to copper zinc tin sulfide Cu2ZnSnS4 a potential material for solar cells10.1039/c2cc30792h ↗
2. Development of CZTS-based thin film solar cells10.1016/j.tsf.2008.11.002 ↗
3. Taylor · 1985
4. Band-gap-graded Cu2ZnSn(S1−x,Se(x))4 solar cells fabricated by an ethanol-based, particulate precursor ink route10.1038/srep03069 ↗
5. Electrical and optical properties of stannite-type quaternary semiconductor thin films10.1143/JJAP.27.2094 ↗
6. Deposition of Cu2ZnSnS4 thin films by vacuum thermal evaporation from single quaternary compound source10.1016/j.matlet.2012.01.018 ↗
7. Preparation of Cu2ZnSnS4 thin films by hybrid sputtering10.1016/j.jpcs.2005.09.037 ↗
8. Characterization of a CZTS thin film solar cell grown by sputtering method10.1016/j.solener.2013.11.035 ↗
9. Development of CZTS thin films solar cells by pulsed laser deposition: influence of pulse repetition rate10.1016/j.solener.2011.03.017 ↗
10. A 5.5% efficient co-electrodeposited ZnO/CdS/Cu2ZnSnS4/Mo thin film solar cell10.1016/j.solmat.2014.02.020 ↗
11. Formation of Cu-Rich and Sn-Poor CZTSSe via Cu3Sn(S,Se)4-ZnS solid-solution as the intermediate10.1021/cm502338q ↗
12. Sprayed films of stannite Cu2ZnSnS410.1016/0169-4332(95)00225-1 ↗
13. Effect of deposition temperature on the structural and electrical properties of spray deposited kesterite (Cu2ZnSnS4) films10.1016/j.solener.2015.09.027 ↗
14. Preparation of Cu2ZnSnS4 thin films by sulfurizing sol–gel deposited precursors10.1016/j.solmat.2007.04.012 ↗
15. Annealing temperature dependence of properties of Cu2ZnSnS4 thin films prepared by sol–gel sulfurization method10.7567/JJAP.50.05FB08 ↗
16. Effects of the sulfurization temperature on sol gel-processed Cu2ZnSnS4 thin films10.1016/j.ceramint.2013.05.039 ↗
17. H2S concentration dependence of properties of Cu2ZnSnS4 thin film prepared under nonvacuum condition10.7567/JJAP.50.05FB09 ↗
18. A nontoxic solvent based sol–gel Cu2ZnSnS4 thin film for high efficiency and scalable low-cost photovoltaic cells10.1039/C5TA02833G ↗
19. Fabrication of Cu2ZnSnS4 solar cells with 5.1% efficiency via thermal decomposition and reaction using a non-toxic sol–gel route10.1039/C3TA13533K ↗
20. A universal chemical potential for sulfur vapours10.1039/C5SC03088A ↗
21. Synthesis and characterization of Cu2ZnSnS4 absorber layers by an electrodeposition-annealing route10.1016/j.tsf.2008.11.022 ↗
22. The influence of sulfurization time and H2S concentration on the properties of Cu2ZnSnS4 thin films10.4028/www.scientific.net/AMR.818.3 ↗
23. Characterization of sulfur poisoning of Ni–YSZ anodes for solid oxide fuel cells using in situ Raman microspectroscopy10.1016/j.ssi.2007.04.004 ↗
24. Influence of H2S concentration on the properties of Cu2ZnSnS4 thin films and solar cells prepared by sol–gel sulfurization10.1016/j.solmat.2011.05.050 ↗
25. OSHA Standards
26. Earth-abundant and low-cost CZTS solar cell on flexible molybdenum foil10.1039/C4RA02064B ↗
27. Cu2ZnSnS4 thin film solar cells by fast coevaporation10.1002/pip.976 ↗
28. On the formation mechanisms of Zn-rich Cu2ZnSnS4 films prepared by sulfurization of metallic stacks10.1016/j.solmat.2013.01.015 ↗
29. Chemical composition dependence of morphological and optical properties of Cu2ZnSnS4 thin films deposited by sol–gel sulfurization and Cu2ZnSnS4 thin film solar cell efficiency10.1016/j.solmat.2010.10.031 ↗
30. Photoelectric properties of Cu2ZnSnS4 thin films deposited by thermal evaporation10.1088/1674-4926/33/2/022002 ↗
31. Synthesis and characterization of CZTS thin films by sol-gel method without sulfurization
32. Thermodynamic properties of minerals and related substances at 298.15K and 1bar (105pascals) pressure and at higher temperatures