journal article·2013-10

Using hydrofluoric acid to reduce the contact resistance of screen-printed silicon solar cells – Its recombination impact and a method to eliminate it

Kee Soon Wang, Alison J. Lennon, Budi S. Tjahjono, Ashraf Uddin, Stuart R. Wenham

Publisher page

Abstract

Abstract Using hydrofluoric acid (HF) to improve the contact resistance of a screen-printed silicon solar cell with a high sheet resistance emitter was found to concurrently reduce its pseudo-fill factor. By treating the cell in phosphoric acid, this impact was found to be significantly reduced or eliminated. In the solar cell presented in this work, the pseudo-fill factor reduced from 82.1% to 79.9% after treating the cell in HF, but increased to 81.8% after a subsequent phosphoric acid treatment. Similar effects were found in three other screen-printed solar cells that were fired at different peak furnace temperatures and belt speeds. It was also shown that the phosphoric acid treatment alone does not affect the pseudo-fill factor of a cell. HF treatment can now be used to reduce the contact resistance of a screen-printed silicon solar cell with a high sheet resistance emitter without suffering from a lower pseudo-fill factor so that the full benefit of a HF treatment on a screen-printed silicon solar cell can be realized. This combination of HF and phosphoric acid treatments can potentially be a useful failure analysis method for screen-printed silicon solar cells in the production line and the laboratory.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Silicon and Solar Cell Technologies · Semiconductor materials and interfaces · Thin-Film Transistor Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (22)

Show source-provided references
1. Green · 1998
2. M.M. Hilali, B. To, A. Rohatgi, A review and understanding of screen-printed contacts and selective-emitter formation, in: Proceedings of the 14th Workshop on Crystalline Silicon Solar Cells and Modules NREL, Winter Park, Colorado, USA, 2004, pp. 80401.
3. Effect of Ag particle size in thick-film Ag paste on the electrical and physical properties of screen-printed contacts and silicon solar cells10.1149/1.2126579 ↗
4. Understanding and formation of high-quality thick-film Ag contacts on high sheet-resistance Si emitters for solar cells10.1149/1.2001507 ↗
5. Physical understanding of printed thick-film front contacts of crystalline Si solar cells—review of existing models and recent developments10.1016/j.solmat.2006.03.040 ↗
6. High-temperature contact formation on n-type silicon: basic reactions and contact model for seed-layer contacts10.1002/adfm.200901305 ↗
7. Electronic properties of nanoscale silver crystals at the interface of silver thick film contacts on n-type silicon10.1063/1.3508950 ↗
8. Comprehensive analysis of advanced solar cell contacts consisting of printed fine-line seed layers thickened by silver plating10.1002/pip.855 ↗
9. Effects of processing parameters on thick film inks used for solar cell front metallization10.1016/0379-6787(81)90019-3 ↗
10. A. Ebong, D.S. Kim, A. Rohatgi, W. Zhang, Understanding the mechanism of light induced plating of silver on screen-printed contacts for high sheet resistance emitters with low surface phosphorus concentration, in: Proceedings of the 33rd IEEE Photovoltaic Specialists Conference, San Diego, 2008, pp. 1–5.10.1109/PVSC.2008.4922674 ↗
11. 〈http://www.secondmetal.eu/fileadmin/secondmetal/docs/Session1/4_recaman_epi_emitters.pdf〉, (accessed 23 02 2013).
12. R.A. Sinton and A. Cuevas, A quasi-steady-state open-circuit voltage method for solar cell characterization, in: Proceedings of the 16th European Photovoltaic Solar Energy Conference, Glasgow, 2000, pp. 1152–1155.
13. Kern · 1993
14. DuPont PV145 silver paste Material Safety Data Sheet.
15. Advanced luminescence based effective series resistance imaging of silicon solar cells10.1063/1.2982588 ↗
16. 〈http://www.btimaging.com/?page_id=81〉, January 2012.
17. D. Wang, B.S. Tjahjono, A. Uddin, S.R. Wenham, Modelling the cell output of the laser-doped semiconductor fingers solar cell design, in: Proceedings of the 5th World Conference on Photovoltaic Energy Conversion, Valencia, 2010, pp. 1401–1404.
18. K.R. McIntosh, Humps, lumps and bumps: three detrimental effects in the current-voltage curve of silicon solar cells, Ph.D. thesis, Department of Photovoltaic Engineering, University of New South Wales, Sydney, Australia, 2001.
19. A. Sugianto, B.S. Tjahjono, J.H. Guo, S.R. Wenham, Impact of laser-induced defects on the performance of solar cells using localised laser doped regions beneath the metal contacts, in: Proceedings of the 22nd European Photovoltaic Solar Energy Conference, Milan, 2007, pp. 1759–1762.
20. B.S. Tjahjono, Laser doped selective emitter silicon solar cells, Ph.D. thesis, School of Photovoltaic and Renewable Energy Engineering, University of New South Wales, Sydney, Australia, 2010.
21. Electrical properties of screen printed silicon solar cell dependent upon thermophysical behaviour of glass frits in Ag pastes
22. Lead immobilization using phosphoric acid in a smelter-contaminated urban soil10.1021/es001770d ↗