journal article·2023-03Open access

Industrially viable diffused IBC solar cells using APCVD dopant glass layers

Vaibhav V. Kuruganti, Daniel Wurmbrand, Thomas Buck, Sven Seren, Miro Zeman, Olindo Isabella, Fabian Geml, Heiko Plagwitz, Barbara Terheiden, Valentin D. Mihailetchi

Abstract

Even though interdigitated back contact (IBC) architecture produces the most efficient solar cells, it is difficult to make them cost-effective and industrially viable. Therefore, single-sided atmospheric pressure chemical vapor deposition (APCVD) is investigated for the fabrication of IBC solar cells because it reduces the overall thermal budget, simplifies wet bench processing, and requires no additional masking layer. For the fabrication of a full APCVD IBC solar cell, a very lightly doped front surface field (FSF) of 650 Ω/sq, a heavier doped back surface field (BSF) of 100 Ω/sq and a moderately doped emitter of 250 Ω/sq was used. The high-temperature annealing step is partially done in an oxygen (O2) environment to (i) drive in dopants, (ii) prevent the formation of a boron-rich layer in case of p+ doped c-Si, and (iii) grow an in-situ SiO2 at the Si/dopant glass interface. The etch rate difference between the in-situ grown SiO2 and the doped glass layer is utilized to etch the doped glass completely. The retained in-situ SiO2 after etching is capped with plasma-enhanced chemical vapor deposited (PECVD) SiNx for the passivation of both polarities of IBC solar cells. A full APCVD IBC solar cell precursors (i.e. before metallization) obtained implied open-circuit voltage (iVoc) of 714 mV and emitter saturation current density (J0s) of 17 fA/cm2. At the device level, a full APCVD IBC solar cell achieved a conversion efficiency of 22.8% with Voc of 696 mV and short-circuit current density JSC of 41.3 mA/cm2. These parameters are comparable to the commercially available full-tube diffused ZEBRA® IBC solar cells.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Silicon and Solar Cell Technologies · Thin-Film Transistor Technologies · Semiconductor materials and interfaces

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (36)

Show source-provided references
1. A new silicon p-n junction photocell for converting solar radiation into electrical power [3]10.1063/1.1721711 ↗
2. The interdigitated back contact solar cell: a silicon solar cell for use in concentrated sunlight10.1109/T-ED.1977.18738 ↗
3. An interdigitated back contact solar cell with high efficiency under concentrated sunlight
4. Exceeding conversion efficiency of 26% by heterojunction interdigitated back contact solar cell with thin film Si technology10.1016/j.solmat.2017.06.024 ↗
5. Silicon solar cells with total area efficiency above 25
6. Kopecek · 2021 · 1008
7. The 2020 photovoltaic technologies roadmap10.1088/1361-6463/ab9c6a ↗
8. Industrial TOPCon solar cells realised by a PECVD tube process
9. Simplified backside-contact solar cells
10. Direct patterned etching of silicon dioxide and silicon nitride dielectric layers by inkjet printing10.1016/j.solmat.2009.06.028 ↗
11. The zebra cell concept - large area n-type interdigitated back contact solar cells and one-cell modules fabricated using standard industrial processing equipment
12. 22.0% Efficient laser doped back contact solar cells10.1016/j.egypro.2013.07.274 ↗
13. Pilot production of 6" IBC solar cells yielding a median efficiency of 23% with a low-cost industrial process
14. Co-diffusion from APCVD BSG and POCl3 for industrial n-type solar cells10.1016/j.egypro.2013.07.282 ↗
15. Gettering efficacy of diffusion processes based on doped APCVD glasses10.1063/1.5049322 ↗
16. Carsten Demberger, Florian Mutter, "Phosphorous doping from APCVD deposited PSG
17. Comparison of laser-doped emitters from as-deposited and thermally diffused APCVD doping glasses on silicon substrates10.1063/1.5123865 ↗
18. TOPCon – technology options for cost efficient industrial manufacturing10.1016/j.solmat.2021.111100 ↗
19. Fundamental understanding, impact, and removal of boron-rich layer on n-type silicon solar cells10.1016/j.solmat.2015.11.031 ↗
20. Surface passivation of boron-diffused junctions by a borosilicate glass and in situ grown silicon dioxide interface layer10.1109/JPHOTOV.2018.2792422 ↗
21. Solar cells with laser doped boron layers from atmospheric pressure chemical vapor deposition
22. Latest Results in Screen-Printed IBC-ZEBRA Solar Cells
23. Anomalously high lifetimes measured by quasi-steady-state photoconductance in advanced solar cell structures10.1063/1.4840337 ↗
24. Thermal oxidation of heavily doped silicon10.1149/1.2423562 ↗
25. Glass source diffusion in Si and SiO[sub 2]10.1149/1.2408020 ↗
26. Impact of boron rich layer on performance degradation in boric acid diffused emitters for n-type crystalline Si solar cells10.1088/2053-1591/aaa2b6 ↗
27. Phosphorus and boron diffusion in silicon under equilibrium conditions10.1063/1.1566464 ↗
28. Chu and Haifeng
29. Laser structuring for back junction silicon solar cells10.1002/pip.732 ↗
30. James · Mater. Sci. Eng. Handb. · 2001 · 232
31. Wet chemical etching of silicate glasses in hydrofluoric acid based solutions10.1007/BF01352182 ↗
32. Etching of oxides
33. A comparison study of boron emitter passivation by silicon oxide and a PECVD silicon nitride stack10.1016/j.egypro.2017.09.301 ↗
34. Thermal oxidation of heavily doped silicon10.1149/1.2423562 ↗
35. A freeware 1D emitter model for silicon solar cells
36. Extremely low surface recombination velocities on heavily doped planar and textured p+ silicon using low-temperature positively-charged PECVD SiOx/SiNx dielectric stacks with optimised antireflective properties