journal article·2018-03

Mechanical and electrical properties of wave-shaped wires for low-stress interconnection of solar cells

L.C. Rendler, J. Walter, S. Goldenberg, A.J. Beinert, S. Wiese, U. Eitner

Publisher page

Abstract

Abstract In the manufacturing process of a common solar module, crystalline silicon solar cells are interconnected by soldering. Copper-based interconnectors, coated with a solder alloy are soldered on both sides of the solar cells on the contact metallization. Subsequently, the solar cell strings are embedded in between two sheets of encapsulant, commonly ethylene-vinyl acetat (EVA), which itself attaches to a front glass and a back sheet during the lamination process. Thermomechanical stress, due to the mismatch of the coefficients of thermal expansion (CTE) of copper and silicon, causes bowing of a back-contact solar cell after the soldering process. Additionally, thermomechanical stress can result in the failure of solder joints. By adapting the mechanical properties of an interconnector, thermomechanical stress can be reduced. Shaping a straight wire with a round cross section to a wave-like form reduces its effective tensile mechanical properties and leads to changes of its effective electrical conductivity. This study investigates the mechanical and electrical properties of wave-shaped wires with different amplitudes, periods and diameters. In addition, microscopic imaging reveals the geometry and potential defects due to the shaping process. The influence of the shaping process on the yield limit of commercially available copper-based wires is determined. For this reason, an algorithm is designed that allows the automatic and precise determination of the yield limit of these interconnectors. In this study, a maximum yield limit reduction of 88.5% compared to a straight wire is found. Furthermore, the influence of the shaping process on the electrical resistance is analyzed. For this purpose, the influence of wire damaging due to the shaping process, as well as the wires longitudinal length change is determined. An increase of the electrical resistance between 3.5% and 82.7% is measured. To choose an optimal interconnection concept for solar cells, the mechanical, as well as the electrical properties of the interconnectors have to be considered. This study correlates the advantageous longitudinal softness of wave-shaped wires, which potentially leads to a significant decrease of the thermomechanical stress in solar cells and of the bowing of back-contact solar cells, with the disadvantageous increase of the electrical resistance caused by the shaping process. The findings enable an optimization of a wire-based interconnection concept for back-contact solar cells.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Silicon and Solar Cell Technologies · Integrated Circuits and Semiconductor Failure Analysis · Photovoltaic System Optimization Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (25)

Show source-provided references
1. S. Schindler, J. Schneider, C. Poenisch, R. Nissler, D. Habermann, Soldering process and material characterization of miniaturized contact structures of a newly developed multi busbar cell metallization concept, in: Proceedings of the 28th European Photovoltaic Solar Energy Conference and Exhibition, 2013, pp. 480–483. 〈http://dx.doi.org/10.4229/28thEUPVSEC2013-1CV.2.13〉.
2. Multi-wire interconnection of busbar-free solar cells10.1016/j.egypro.2014.08.109 ↗
3. LG Electronics, Preisverdächtig nach München: LG Electronics mit neuem NeON 2 und Cello-Technologie Anwärter auf Intersolar Award 2015. 〈http://presse.lge.de/2015/05/11/preisverdaechtig-nach-muenchen-lg-electronics-mit-neuem-neon-2-und-cello-technologie-anwaerter-auf-intersolar-award-2015/〉, Published: Mai 11, 2015, Requested: June 21, 2017.
4. T. Söderström, P. Papet, J. Ufheil, Smart wire connection technology, in: Proceedings of the 28th European Photovoltaic Solar Energy Conference and Exhibition, 2013, pp. 495–499. 〈http://dx.doi.org/10.4229/28thEUPVSEC2013-1CV.2.17〉.
5. A. Schneider, L. Rubin, G. Rubin, Solar cell efficiency improvement by new metallization techniques – the day4TM electrode concept, in: Proceedings of the 4th World Conference on Photovoltaic Energy Conversion, 2006, pp. 1095–1098. 〈http://dx.doi.org/10.1109/WCPEC2006.279333〉.
6. Solar cell improvement by using a multi busbar design as front electrode10.1016/j.egypro.2012.07.056 ↗
7. Multi-Busbar solar cells and modules: high efficiencies and low silver consumption10.1016/j.egypro.2013.07.286 ↗
8. A.F. Dethlefsen, M. Volk, K. Ramspeck, C. Buchner, Reliability testing of multi-busbar modules, in: Proceedings of the 29th European Photovoltaic Solar Energy Conference and Exhibition, 2014, pp. 3323–3326. 〈http://dx.doi.org/10.4229/EUPVSEC20142014-5CV.2.38〉.
9. J. Walter, L.C. Rendler, I. Dürr, C. Ebert, A. Kraft, U. Eitner, Solder joint stability study of wire-based interconnection compared to ribbon interconnection, Energy Procedia 124, 2017, pp. 515–525, https://doi.org/10.1016/j.egypro.2017.09.288.10.1016/j.egypro.2017.09.288 ↗
10. Silicon heterojunction solar cell with interdigitated back contacts for a photoconversion efficiency over 26%10.1038/nenergy.2017.32 ↗
11. Solar cell efficiency tables (version 50)10.1002/pip.2909 ↗
12. SunPower Corporation, SunPower® module degradation rate, 〈https://us.sunpower.com/sites/sunpower/files/media-library/white-papers/wp-sunpower-module-degradation-rate.pdf〉, Published: 2013, Requested: June 21, 2017.
13. L.C. Rendler, A. Kraft, C. Ebert, U. Eitner, S. Wiese, Mechanical stress in solar cells with multi busbar interconnection – parameter study by FEM simulation, in: Proceedings of the 17th EuroSimE, 2016, pp. 1–5. 〈http://dx.doi.org/10.1109/EuroSimE2016.7463325〉.
14. L.C. Rendler, A. Kraft, C. Ebert, S. Wiese, U. Eitner, Investigation of thermomechanical stress in solar cells with multi busbar interconnection by finite element modeling, in: Proceedings of the 32nd EUPVSEC, 2016, pp. 94–98. 〈http://dx.doi.org/10.4229/EUPVSEC20162016-1CO.11.2〉.
15. R. Meier, M. Pander, R. Klengel, S. Dietrich, S. Klengel, M. Ebert, J. Bagdahn, Reduction of soldering induced stresses in solar cells by microstructural optimization of copper-ribbons, in: Proceedings of the SPIE Solar Energy+ Technology, 2011, pp. 811206-1–811206-13. 〈http://dx.doi.org/10.1117/12.893519〉.10.1117/12.893519 ↗
16. Y. Zemen, T. Prewitz, T. Geipel, S. Pingel, J. Berghold, The impact of yield strength of the interconnector on the internal stress of the solar cell within a module, in: Proceedings of the 5th World Conference on Photovoltaic Energy Conversion, 2010, pp. 4073–4078. 〈http://dx.doi.org/10.4229/25thEUPVSEC2010-4AV.3.38〉.
17. J. Walter, L.C. Rendler, A. Halm, V. Mihailetchi, A. Kraft, U. Eitner, Ribbon Interconnection of 6′′ BC-BJ Solar Cells, Energy Procedia 124, 2017, pp. 504–514, https://doi.org/10.1016/j.egypro.2017.09.287.10.1016/j.egypro.2017.09.287 ↗
18. L.C. Rendler, J. Walter, A. Kraft, C. Ebert, S. Wiese, U. Eitner, Ultra-soft wires for direct soldering on finger grids of solar cells, Energy Procedia 124, 2017, pp. 478–483, https://doi.org/10.1016/j.egypro.2017.09.284.10.1016/j.egypro.2017.09.284 ↗
19. H. Wirth, M. Tranitz, C. Malchow, F. Clement, New technologies for back contact module assembly, in: Proceedings of the 25th European Photovoltaic Solar Energy Conference and Exhibition, 2010, pp. 3846–3849. 〈http://dx.doi.org/10.4229/25thEUPVSEC2010-4CO.19.3〉.
20. U. Eitner, D. Eberlein, M. Tranitz, Interconnector-based module technology for thin MWT cells, in: Proceedings of the 27th European Photovoltaic Solar Energy Conference and Exhibition, 2012, pp. 3461–3464. 〈http://dx.doi.org/10.4229/27theupvsec2012-4bv.3.14〉.
21. IEC 61215 Ed. 2.0, Crystalline Silicon Terrestrial Photovoltaic (PV) Modules – Design Qualification and Type Approval.
22. ISO 6892-1, Metallic materials – Tensile Testing, 2009.
23. Mechanical problems of novel back contact solar modules10.1016/j.microrel.2013.02.019 ↗
24. Unified methodology for determining CTM ratios: systematic prediction of module power10.1016/j.solmat.2014.06.025 ↗
25. Systematic PV module optimization with the cell-to-module (CTM) analysis software