Forming aluminum electrodes by screen printing and electron-beam evaporation for high performance interdigitated back contact solar cells
Source abstract
Abstract
Abstract Interdigitated back contact (IBC) solar cell is one of the most efficient silicon solar cells commercially available to date. This paper studies the application of aluminum electrodes, deposited by electron-beam evaporation, instead of commonly used silver paste. Furthermore, screen printing instead of optical lithography method was used to generate etching masks. Together, we develop a low-cost technology for production. The specific contact resistivity of Al was found to be even lower than that of traditionally used Ag paste. The specific contact resistivity ( ρ c ) and the recombination parameter ( J o ) were found to be dependent on the doping level. Therefore, there is a design trade-off between a low J o obtained with a low surface doping concentration, and a low ρ c obtained with a high surface doping concentration. This process produced an IBC solar cell with a size of 4 cm 2 , an open circuit voltage of 680 mV, a conversion efficiency ( η ) of 22.72%, a fill factor of 0.80, and a short circuit current density of 41.69 mA/cm 2 . The optimal design for the Al contact IBC cell was found by comparing the 3D Quokka© simulations of the Al contact and Ag paste contact IBC cells. The simulation indicated that further decrease in the Al contact size and spacing using screen printing and optimize the doping level could result in η up to 23.4% in production, comparable to the performance achieved in small cells using optical lithography.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Silicon and Solar Cell Technologies · solar cell performance optimization · Nanowire Synthesis and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (26)
Show source-provided references
1. The interdigitated back contact solar cell: a silicon solar cell for use in concentrated sunlight10.1109/T-ED.1977.18738 ↗
2. Point-contact silicon solar cells10.1109/T-ED.1984.21586 ↗
3. A.W. Blakers, K.C. Fong, E. Franklin, T.C. Kho, K.R. McIntosh, Y. Wan, D. Wang, N.S. Zin, 24.6% efficient back contact cell with oxide–nitride passivation, in: Proceedings of the 23rd International Photovoltaic Science and Engineering Conference (PVSEC), Taipei, 2013.
4. S. Singh, B. O’Sullivan, M. Récaman-Payo, A. Uruena de Castro, M. Debucquoy, J. Szlufcik, J. Poortmans, Process development on photolithography free IBC solar cells, in: Proceedings of the 29th European Photovoltaic Solar Energy Conference and Exhibition (EU PVSEC), Amsterdam, 2014.
5. Damage-free ultraviolet nanosecond laser ablation for high efficiency back contact solar cell fabrication10.1016/j.solmat.2014.12.030 ↗
6. Toward the practical limits of silicon solar cells10.1109/JPHOTOV.2014.2350695 ↗
7. Large-area back-contact back-junction solar cell with efficiency exceeding 21%10.1109/JPHOTOV.2012.2224848 ↗
8. K.C. Fong, K. Teng, K.R. McIntosh, A.W. Blakers, E. Franklin, N.S. Zin, A. Fell, Optimisation of n+ diffusion and contact size of IBC solar cells, in: Proceedings of the 28th European Photovoltaic Solar Energy Conference and Exhibition (EU PVSEC), Paris, 2013.
9. High rate electron beam evaporation10.1016/0040-6090(83)90219-5 ↗
10. J.P. Heinss, C. Mader, A. Merkle, T. Brendemuehl, R. Brendel, L. Ehlers, R. Meyer, In-line high-rate deposition of aluminum onto RISE solar cells by electron beam technology, in: Proceedings of the 26th European Photovoltaic Solar Energy Conference and Exhibition (EU PVSEC), Hamburg, 2011.
11. Solar cell contact resistance – a review10.1109/T-ED.1984.21583 ↗
12. Reverse saturation current density imaging of highly doped regions in silicon: a photoluminescence approach10.1016/j.solmat.2012.05.026 ↗
13. Optimisation of interdigitated back contacts solar cells by two-dimensional numerical simulation10.1016/j.solmat.2004.09.010 ↗
14. 3-D simulation of interdigitated-back-contact silicon solar cells with quokka including perimeter losses10.1109/JPHOTOV.2014.2320302 ↗
15. J. Benick, B. Hoex, G. Dingemans, W.M.M. Kessels, A. Richter, M. Hermle, S.W. Glunz, High-efficiency n-type silicion solar cells with front side boron emitter, in: Proceedings of the 24th European Photovoltaic Solar Energy Conference and Exihibition (EU PVSEC), Hamburg, 2009.
16. E. Lohmüller, S. Werner, J. Schön, M. Thanasa, S. Mack, W. Wolke, A. Wolf, F. Clement, D. Biro, Depletion of boron-doped surfaces protected with barrier layers during POCl3-diffusion, in: Proceedings of the 28th European Photovoltaic Solar Energy Conference and Exhibition (EU PVSEC), Paris, 2013.
17. F. Granek, M. Hermle, C. Reichel, A. Grohe, O. Schultz-Wittmann, S. Glunz, Positive effects of front surface field in high-efficiency back-contact back-junction n-type silicon solar cells, in: Proceedings of the 33rd IEEE Photovoltaic Specialists Conference (PVSC), San Diego, 2008, pp. 1–5.10.1109/PVSC.2008.4922759 ↗
18. Aluminum–silicon ohmic contact on “shallow” n+/p+ junctions10.1016/0038-1101(80)90011-8 ↗
19. Obtaining the specific contact resistance from transmission line model measurements10.1109/EDL.1982.25502 ↗
20. 19.7% Efficient all-screen-printed back-contact back-junction silicon solar cell with aluminum-alloyed emitter10.1109/LED.2010.2097238 ↗
21. Simple power-loss analysis method for high-efficiency Interdigitated Back Contact (IBC) silicon solar cells10.1016/j.solmat.2012.06.008 ↗
22. Fill factor in organic solar cells10.1039/c3cp51383a ↗
23. Temperature dependence of solar cell performance – an analysis10.1016/j.solmat.2012.02.019 ↗
24. Contact resistance: its measurement and relative importance to power loss in a solar cell10.1109/T-ED.1984.21584 ↗
25. F. Zeng, Y. Feng, Z. Liang, H. Shen, Specific contact resistance measurements on C–Si solar cells by novel TLM method, in: Proceedings of the 38th IEEE Photovoltaic Specialists Conference (PVSC), Austin, 2012, pp. 000509–000513.10.1109/PVSC.2012.6317667 ↗
26. A. Richter, M. Höteis, J. Benick, S. Henneck, M. Hermle, S.W. Glunz, Towards industrially feasible high-efficiency n-type Si solar cells with boron-diffused front side emitter-combining firing stable Al2O3 passivation and fine-line printing, in: Proceedings of the 35th IEEE Photovoltaic Specialists Conference (PVSC), Hawaii, 2010, pp. 003587–003592.10.1109/PVSC.2010.5614369 ↗