journal article·2016-01

Investigation of the light soaking behaviors in two-step sputter and selenization Cu(In,Ga)(Se,S)2 solar cells with different sulfur ratios

JungYup Yang, Junggyu Nam, Dongseop Kim, Dongho Lee, PilHo Huh

Publisher page

Abstract

Abstract Cu(In,Ga)(S,Se)2 (CIGSSe) solar cells with different S/(S+Se) (SSSe) ratios were fabricated using a sequential two-step sputtering and selenization/sulfurization process. The origins of the light soaking behavior in the CIGSSe absorber layer were studied based on the light soaking time (or dark storage time) dependence of the open circuit voltage (Voc) and built in potential (Vbi) as well as the temperature dependence of the current–voltage curve. In CIGSSe devices with a SSSe ratio >0.35, Voc and Vbi increase with increasing light soaking time and decrease with increasing dark storage time. In contrast, the Voc and Vbi of the CIGSSe devices with a SSSe ratio of approximately 0.25 showed slightly different behaviors, an increase with increasing light soaking time but little change with increasing dark storage time. The reasons for the different behavior in the CIGSSe devices with different SSSe ratios were attributed mainly to changes in the interface state by the SSSe ratio at the CIGSSe/buffer interface. The results suggest that the control of the SSSe ratio in the CIGSSe absorber fabricated by the proposed two-step process is an important key to determining the light soaking characteristics of the solar cell devices.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Chalcogenide Semiconductor Thin Films · Quantum Dots Synthesis And Properties · Semiconductor materials and interfaces

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (26)

Show source-provided references
1. Effect of combined heat and light soaking on device performance of Cu(In,Ga)Se2 solar cells with ZnS(O,OH) buffer layer10.1002/pip.2339 ↗
2. Persistent photoconductivity in Cu(In,Ga)Se2 heterojunctions and thin film prepared by sequential deposition10.1063/1.121762 ↗
3. Fabrication of graded band-gap Cu(InGa)Se2 thin-film mini-modules with a Zn(O,S,OH)x buffer layer10.1016/S0927-0248(97)00204-3 ↗
4. R.A. Sasala, J.R. Sites, Time Dependent Voltage CuInSe2 and CdTe Solar Cells, In: Proceedings of the 23rd IEEE PVSC, 1993, pp. 543–548.10.1109/PVSC.1993.347036 ↗
5. Classification of metastabilities in the electrical characteristics of ZnO/CdS/Cu(In,Ga)Se2 solar cells10.1016/S0040-6090(00)01850-2 ↗
6. Light and bias induced metastabilities in Cu(In,Ga)Se2 based solar cells caused by the (VSe–VCu) vacancy complex10.1063/1.2388256 ↗
7. Distinguishing metastable changes in bulk CIGS defect densities from interface effects10.1016/S0040-6090(03)00189-5 ↗
8. Light soaking effects in Cu(In,Ga)Se2 superstrate solar cells10.1016/S0040-6090(03)00187-1 ↗
9. CuGaSe2-based superstrate solar cells10.1016/S0040-6090(00)01711-9 ↗
10. Charging and discharging of defect states in CIGS/ZnO junctions10.1016/S0040-6090(99)00787-7 ↗
11. Temperature-dependent current–voltage and light soaking measurements on Cu(In,Ga)Se2 solar cells with ALD-Zn1−xMgxO buffer layers10.1002/pip.912 ↗
12. Understanding the light soaking effect of ZnMgO buffer in CIGS solar cells10.1039/C5CP01758K ↗
13. Mechanical properties and fracture analysis of glass substrate for PDPs10.1889/1.1825678 ↗
14. Chris A. Deline, David S. Albin, Steve R. Rummel, Metastable electrical characteristics of polycrystalline thin-film photovoltaic modules upon exposure and stabilization, Conference Paper, 2011, NREL/CP-5200-52441.10.1117/12.893813 ↗
15. Defects in Cu(In,Ga)Se2 Chalcopyrite Semiconductors: a comparative study of material properties, defect states, and photovoltaic performance10.1002/aenm.201100344 ↗
16. Electronic loss mechanisms in chalcopyrite based heterojunction solar cells10.1016/S0040-6090(99)00762-2 ↗
17. Electronic properties of CuGaSe2-based heterojunction solar cells. Part I. Transport analysis10.1063/1.371903 ↗
18. Electrical characterization of Cu(In,Ga)Se2 thin-film solar cells and the role of defects for the device performance10.1016/S0927-0248(00)00273-7 ↗
19. Distinction between bulk and interface states in CuInSe2/CdS/ZnO by space charge spectroscopy10.1063/1.366686 ↗
20. Oxygenation and air-annealing effects on the electronic properties of Cu(In,Ga)Se2 films and devices10.1063/1.370758 ↗
21. Bulk and metastable defects in CuIn1−xGaxSe2 thin films using drive-level capacitance profiling10.1063/1.1633982 ↗
22. Influence of surface properties on the performance of Cu(In,Ga)(Se,S)2 thin-film solar cells using Kelvin probe force microscopy10.1039/C5RA05330G ↗
23. Fabrication of pentanary Cu(InGa)(SeS)2 absorbers by selenization and sulfurization10.1016/j.solmat.2009.02.004 ↗
24. Role of incorporated sulfur into the surface of Cu(InGa)Se2 thin-film absorber10.1016/S0927-0248(00)00288-9 ↗
25. Impact of the Band Offset for n-Zn(O,S)/p-Cu(In,Ga)Se2 Solar Cells10.1109/JPHOTOV.2014.2298093 ↗
26. Jüri Krustok, Mati Danilson, Andri Jagomägi, Maarja Grossberg, Jaan Raudoja, Device characteristics of CuInSe2-based solar cells, Proc. SPIE 5946, Optical Materials Applications, 2006, 59460W.10.1117/12.639060 ↗