journal article·2022-06Open access

Multijunction solar cell mesa isolation: Correlation between process, morphology and cell performance

Mathieu de Lafontaine, Farah Ayari, Erwine Pargon, Guillaume Gay, Camille Petit-Etienne, Artur Turala, Gwenaelle Hamon, Abdelatif Jaouad, Maïté Volatier, Simon Fafard, Vincent Aimez, Maxime Darnon

Abstract

Multijunction solar cells must be electrically isolated from one to another at the end of the fabrication process; a step known as mesa isolation. In this study, three different techniques are assessed to perform this step: saw-dicing, wet etching and plasma etching. Triple junction solar cells were fabricated with each process and the open-circuit voltages were measured in order to compare the impact of each technique on the device performance. An optional wet treatment is also proposed to clean the sidewalls after the mesa isolation process. The mesa sidewalls were characterized by scanning electron microscopy and atomic force microscopy to assess the profile length and roughness respectively. The cell performance was then correlated to the sidewall length and roughness for all three isolation techniques. This study indicates that a plasma etching process followed by a wet clean is the process that maximizes the solar cell performance, thanks to a short profile length
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: solar cell performance optimization · Silicon and Solar Cell Technologies · Photovoltaic System Optimization Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (19)

Show source-provided references
1. Multijunction solar cell mesa isolation: a comparative study
2. Plasma etching applications in concentrated photovoltaic cell fabrication10.1063/1.4962091 ↗
3. InGaAsNSb/Ge double-junction solar cells grown by metalorganic chemical vapor deposition10.1016/j.solener.2014.01.019 ↗
4. Nonselective etching of As and P based III–V solar cell heterostructures with aqueous solutions of HIO3 and HCl10.1016/j.solmat.2021.111097 ↗
5. Development of wet etch processing for InxAl1-xAsySb1-y solar cells grown on InP
6. Developing methods for wet chemical etching of a separation mesa structure during creation of multijunction solar cells10.1134/S1063785019120241 ↗
7. Isolation of III-V/Ge multijunction solar cells by wet etching10.1155/2013/583867 ↗
8. Six-junction III–V solar cells with 47.1% conversion efficiency under 143 suns concentration10.1038/s41560-020-0598-5 ↗
9. Processing techniques for monolithic interconnection of solar cells at wafer level10.1109/TED.2010.2076190 ↗
10. Miniaturization of InGaP/InGaAs/Ge solar cells for micro-concentrator photovoltaics10.1002/pip.3421 ↗
11. Influence of plasma process on III-V/Ge multijunction solar cell via etching10.1016/j.solmat.2019.01.048 ↗
12. Anisotropic and low damage III-V/Ge heterostructure etching for multijunction solar cell fabrication with passivated sidewalls10.1016/j.mne.2021.100083 ↗
13. Analysis of perimeter recombination in the subcells of gainp/gaas/ge triple-junction solar cells
14. Modelling of the perimeter recombination effect in GaAs-based micro-solar cell10.1016/j.solmat.2005.01.009 ↗
15. Voltage losses due to the perimeter and dark area in micro-concentrator solar cells10.1016/j.solmat.2020.110791 ↗
16. A review of the promises and challenges of micro-concentrator photovoltaics10.1063/1.5001441 ↗
17. Fafard · 2001
18. An atomic force microscopy-based method for line edge roughness measurement10.1063/1.4794368 ↗
19. Removal of dry etch damage in p-type gan by wet etching of sacrificial oxide layer10.1116/1.1645880 ↗