Analysing the lateral series resistance of high-performance metal wrap through solar cells
Source abstract
Abstract
Abstract In back-contact solar cells, both external polarities are located at the back surface of the device, which allows for higher photocurrent generation on cell level and reduced series resistance on module level, leading to higher energy conversion efficiencies compared to conventional solar cells and modules. However, the majority charge carriers, which are generated near the back emitter, have to flow laterally e.g. through the base in order to reach the external majority carrier contact. In the present work, we analyse the lateral series resistance by means of measurement and simulation for high-performance metal wrap through (HIP-MWT) solar cells. We compare theoretical models and experimental methods to extract the effective series resistance from simulated and measured current–voltage characteristics and show that lateral voltage variations significantly increase the local recombination current. If the width of the gap between the external majority carrier contacts is reduced from the typical value of 3.5 mm to ideally 0 mm, we expect an increase of the energy conversion efficiency of approximately 0.1%abs. for cells with three continuous rear emitter contacts on 125 mm×125 mm large silicon wafers. In a simulation study, the bulk doping concentration N A and the bulk lifetime are varied yielding an optimal base resistivity of 0.6 Ω cm–1.5 Ω cm for HIP-MWT solar cells based on Czochralski-grown silicon in the degraded state of the boron–oxygen defect and an optimal resistivity of less than 1.0 Ω cm for the case of bulk lifetimes larger than ~300 µs.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Silicon and Solar Cell Technologies · Semiconductor materials and interfaces · Thin-Film Transistor Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (38)
Show source-provided references
1. E. van Kerschaver, R. Einhaus, J. Szlufcik, J. Nijs, R. Mertens, A novel silicon solar cell structure with both external polarity contacts on the back surface, in: J. Schmid, H.A. Ossenbrink, P. Helm, H. Ehmann, E.D. Dunlop (Eds.) Proceedings of the 2nd World Conference on Photovoltaic Energy Conversion, Vienna, Austria, 1998, pp. 1479–1482.
2. 17.9% Metal-wrap-through mc-Si cells resulting in module efficiency of 17.0%10.1002/pip.1110 ↗
3. Industrially feasible multi-crystalline metal wrap through (MWT) silicon solar cells exceeding 16% efficiency10.1016/j.solmat.2008.11.059 ↗
4. T. Fellmeth, K. Meyer, J. Greulich, F. Clement, D. Biro, R. Preu, M. Menkoe, D. Lahmer, H.-J. Krokoszinski, Development and modelling of crystalline silicon based metal wrap through (mwt) solar cells, in: Proceedings of the 25th European Photovoltaic Solar Energy Conference and Exhibition, Valencia, Spain, 2010, pp. 2201–2206.
5. T. Fellmeth, J. Greulich, F. Clement, D. Biro, Modelling of silicon solar cells by using an extended two-diode-modell approach, in: Proceedings of the 27th European Photovoltaic Solar Energy Conference and Exhibition, Frankfurt, Germany, 2012, pp. 1394–1397.
6. Effect of series resistance on metal-wrap-through mulit-crystalline silicon solar cells10.1016/j.solmat.2010.04.053 ↗
7. Clement · 2009 · 256
8. 22.8% efficient silicon solar cell10.1063/1.101596 ↗
9. HIP-MWT: A simplified structure for metal wrap through solar cells with passivated rear surface10.1016/j.egypro.2011.06.172 ↗
10. Large-area p-type HIP-MWT silicon solar cells with screen printed contacts exceeding 20% efficiency10.1002/pssr.201105311 ↗
11. S. Mack, U. Jäger, G. Kästner, E.A. Wotke, U. Belledin, A. Wolf, R. Preu, D. Biro, Towards 19% efficient industrial PERC devices using simultaneous front emitter and rear surface passivation by thermal oxidation, in: Proceedings of the 35th IEEE Photovoltaic Specialists Conference, Institute of Electrical and Electronics Engineers, Honolulu, Hawaii, USA, 2010, pp. 17–21.10.1109/PVSC.2010.5614048 ↗
12. E. Schneiderlöchner, R. Preu, R. Lüdemann, S.W. Glunz, G. Willeke, Laser-fired contacts (LFC), in: B. McNelis, W. Palz, H.A. Ossenbrink, P. Helm (Eds.) Proceedings of the 17th European Photovoltaic Solar Energy Conference, WIP—Renewable Energies and ETA Florence, Munich, Germany, 2001, pp. 1303–1306.
13. Laser-fired rear contacts for crystalline silicon solar cells10.1002/pip.422 ↗
14. M. Glatthaar, J. Hohl-Ebinger, A. Krieg, M. Greif, L. Greco, F. Clement, S. Rein, W. Warta, R. Preu, Accurative IV-measurement for back contact solar cells, in: Proceedings of the 25th European Photovoltaic Solar Energy Conference and Exhibition, Valencia, Spain, 2010, pp. 2118–2120.
15. Comprehensive analytical model for locally contacted rear surface passivated solar cells10.1063/1.3506706 ↗
16. Fischer · 2003 · 198
17. A review and comparison of different methods to determine the series resistance of solar cells10.1016/j.solmat.2007.05.026 ↗
18. A.G. Aberle, S.R. Wenham, M.A. Green, A new method for accurate measurements of the lumped series resistance of solar cells, in: Proceedings of the 23rd IEEE Photovoltaic Specialists Conference, Institute of Electrical and Electronics Engineers, Louisville, Kentucky, USA, 1993, pp. 133–139.10.1109/PVSC.1993.347065 ↗
19. Separation of series resistance and space charge region recombination in crystalline silicon solar cells from dark and illuminated current–voltage characteristics10.1109/JPHOTOV.2012.2189370 ↗
20. Series resistance effects on solar cell measurements10.1016/0365-1789(63)90063-8 ↗
21. I.E. Commission, Photovoltaic devices–procedures for temperature and irradiance corrections to measured I–V characteristics, in, Proceedings of the International Electrotechnical Commission, Geneva, Switzerland, 2009.
22. Sentaurus TCAD, Release E-2010.12, Synopsys Inc., Zürich, Switzerland, 2010.
23. Illumination for computer generated pictures
24. Optical modeling of the rear surface roughness of passivated silicon solar cells10.1016/j.egypro.2012.07.057 ↗
25. Dopant and carrier concentration in Si in equilibrium with monoclinic SiP precipitates10.1103/PhysRevB.53.7836 ↗
26. Numerical modeling of highly doped Si:P emitters based on Fermi-Dirac statistics and self-consistent material parameters10.1063/1.1501743 ↗
27. A unified mobility model for device simulation—I. Model equations and concentration dependence10.1016/0038-1101(92)90325-7 ↗
28. A unified mobility model for device simulation—II. Temperature dependence of carrier mobility and lifetime10.1016/0038-1101(92)90326-8 ↗
29. Models for numerical device simulations of crystalline silicon solar cells—a review10.1007/s10825-011-0367-6 ↗
30. Spatially resolved analysis and minimization of resistive losses in high-efficiency Si solar cells10.1002/(SICI)1099-159X(199611/12)4:6<399::AID-PIP148>3.0.CO;2-4 ↗
31. J.E. Mahan, G.M. Smirnov, A new perspective on distributed series resistance effects in photovoltaic devices, in: Proceedings of the 14th IEEE Photovoltaic Specialists Conference, Institute of Electrical and Electronics Engineers, San Diego, California, USA, 1980, pp. 612–618.
32. A. Drews, F. Clement, A. Spribille, B. Thaidigsmann, M. Linse, S. Gutscher, S. Werner, V. Reitenbach, E. Ould Chighali, A. Wolf, M. Zimmer, J. Nekarda, I. Haedrich, M. Tranitz, U. Eitner, H. Wirth, H.R. Wilson, D. Biro, R. Preu, HIP-MWT solar cells—pilot-line cell processing and module integration, in: Proceedings of the 27th European Photovoltaic Solar Energy Conference and Exhibition, Frankfurt, Germany, 2012, pp. 828–831.
33. Fundamental boron-oxygen-related carrier lifetime limit in mono- and multicrystalline silicon10.1002/pip.586 ↗
34. Ohmic contacts for GaAs devices10.1016/0038-1101(67)90063-9 ↗
35. Spreading resistance between constant potential surfaces10.1002/j.1538-7305.1971.tb01882.x ↗
36. Investigation of laser-fired rear-side recombination properties using an analytical model10.1002/pip.660 ↗
37. Thermal oxidation for crystalline silicon solar cells exceeding 19% efficiency applying industrially feasible process technology10.1002/pip.814 ↗
38. Advanced analytical model for the effective recombination velocity of locally contacted surfaces10.1063/1.3437126 ↗