journal article·2011-03

Solar cells made from polymers containing Dithieno[3,2-b:2′,3′-d]pyrrole with different side chain lengths

Cheng Gong, Hong Bin Yang, Qun Liang Song, Zhi Song Lu, Chang Ming Li

Publisher page

Abstract

Abstract Polymer solar cells made from poly(2,6-bis(3-dodecylthiophen-2-yl)-N-alkyl-dithieno[3,2-b:2′,3′-d]pyrrole) (PDTPBT) with different side chain lengths as donors and [6,6]-phenyl C61-butyric acid methyl ester (PCBM) as the acceptor were investigated. After optimization with thermal treatments, the device made from PDTPBT with a longer alkyl side chain (P1) delivers a power conversion efficiency (PCE) of 1.06%, which is much higher than that made from PDTPBT with a shorter side chain (0.26%). Atomic force microscopy (AFM) and modeling results show that the polymer with longer side chain produces much better uniform nanostructure with less pinhole than the polymer with a short side chain, resulting in lower interfacial resistance for higher short circuit current and reduced cathode penetration into the active layer for lower charge recombination rate, and further leading to higher power conversion efficiency.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Organic Electronics and Photovoltaics · Conducting polymers and applications · Thin-Film Transistor Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (28)

Show source-provided references
1. Polymer photovoltaic cells: enhanced efficiencies via a network of internal donor–acceptor heterojunctions10.1126/science.270.5243.1789 ↗
2. Simple synthesis of monomers for regioregular poly(dialkylbiphenylenevinylene) conducting polymers through directional polymerization10.1021/ma021192g ↗
3. High-efficiency solution processable polymer photovoltaic cells by self-organization of polymer blends10.1038/nmat1500 ↗
4. Metallated conjugated polymers as a new avenue towards high-efficiency polymer solar cells10.1038/nmat1909 ↗
5. Stability/degradation of polymer solar cells10.1016/j.solmat.2008.01.005 ↗
6. Fabrication and processing of polymer solar cells: a review of printing and coating techniques10.1016/j.solmat.2008.10.004 ↗
7. Solution-prepared hybrid-nanoparticle dielectrics for high-performance low-voltage organic thin-film transistors10.1021/am9003914 ↗
8. The degradation of indium tin oxide/pentacene/fullerene/tris-8-hydroxy-quinolinato aluminum/aluminum heterojunction organic solar cells: by oxygen or moisture?10.1016/j.solmat.2010.01.006 ↗
9. Spatially controlled oxygen inhibition of acrylate photopolymerization as a new lithography method for high-performance organic thin-film transistors10.1021/cm9034769 ↗
10. Evidence of harvesting electricity by exciton recombination in an n–n type solar cell10.1021/ja1003735 ↗
11. Degradation patterns in water and oxygen of an inverted polymer solar cell10.1021/ja106299g ↗
12. Polymers for roll-to-roll coated polymer solar cells10.1021/ma1015903 ↗
13. The effect of post-processing treatments on inflection points in current–voltage curves of roll-to-roll processed polymer photovoltaics10.1016/j.solmat.2010.06.007 ↗
14. Upscaling of polymer solar cell fabrication using full roll-to-roll processing10.1039/b9nr00430k ↗
15. Using light-induced thermocleavage in a roll-to-roll process for polymer solar cells†10.1021/am900858x ↗
16. Semiconductive polymers containing Dithieno[3,2-b:2′,3′-d]pyrrole for organic thin-film transistors10.1021/ma802004e ↗
17. Direct observation and analysis of annealing-induced microstructure at interface and its effect on performance improvement of organic thin film transistors10.1021/jp804988h ↗
18. High-performance thin-film transistors from solution-processed dithienothiophene polymer semiconductor nanoparticles10.1021/cm703567g ↗
19. Ex and in situ confocal Raman studies of organic thin film and its on-working transistors10.1021/jp807466e ↗
20. Polymer solar cell based on poly(2,6-bis(3-alkylthiophen-2-yl)dithieno-[3,2-b;2′,3′-d]thiophene)10.1016/j.solmat.2009.07.005 ↗
21. Broadband absorbing bulk heterojunction photovoltaics using low-bandgap solution-processed quantum dots10.1021/nl1013663 ↗
22. Effects of annealing on the nanomorphology and performance of poly(alkylthiophene):fullerene bulk-heterojunction solar cells10.1002/adfm.200601038 ↗
23. Novel NIR-absorbing conjugated polymers for efficient polymer solar cells: effect of alkyl chain length on device performance10.1039/b818885h ↗
24. New method to extract the model parameters of solar cells from the explicit analytic solutions of their illuminated I–V characteristics10.1016/j.solmat.2005.04.023 ↗
25. The influence of the optoelectronic properties of poly(3-alkylthiophenes) on the device parameters in flexible polymer solar cells10.1016/j.orgel.2005.02.004 ↗
26. Influence of the molecular weight of poly(3-hexylthiophene) on the performance of bulk heterojunction solar cells10.1021/cm047811c ↗
27. Thermally stable, efficient polymer solar cells with nanoscale control of the interpenetrating network morphology10.1002/adfm.200500211 ↗
28. Effect of alkyl side-chain length on photovoltaic properties of poly(3-alkylthiophene)/PCBM bulk heterojunctions10.1002/adfm.200900797 ↗