journal article·2012-04

Electropolymerization of 3,4-ethylenedioxythiophene within an insulating nitrile butadiene rubber network: Application to electroreflective surfaces and devices

Isabelle Fabre-Francke, Pierre-Henri Aubert, Séverine Alfonsi, Frédéric Vidal, Laurent Sauques, Claude Chevrot

Publisher page

Abstract

Abstract Innovative designs based on semi-interpenetrating polymers networks (semi-IPN), where an electronic conductive polymer (ECP) is formed within – but on each side – a film of a polymer network chosen both for their mechanical properties and ionic conductivity lead to devices with battery-like architecture. Usually, the route to introduce the ECP is an oxidative chemical polymerization leading to conducting semi-IPN with mixed conductivities (electronic and ionic). We will present the fabrication of such semi-IPN using an electrochemical route to form the ECP. This strategy is interesting since it allows the choice of the electrolytic medium and therefore the nature of the doping ion. This process implies the electropolymerization of the conjugated monomer – 3,4-ethylenedioxythiophene (EDOT) – within a flexible insulating matrix, which is a Nitrile Butadiene Rubber (NBR) network or a flexible IPN made of NBR and a branched polyethylene oxide (PEO) network. In the first part, scanning electron microscopy experiments show that the two-phases composition of the semi-IPN NBR/PEDOT obtained notably the localization of PEDOT inside the NBR matrix. The electropolymerization process is discussed and electrochemical characterization by cyclic voltamograms demonstrates the accessibility of the PEDOT inside the matrix. In the second part, we present first the reflective properties of the NBR/PEDOT semi-IPN. Upon chemical oxidation/reduction processes, it is possible to observe a 25% reflection contrast in the Near Infrared (NIR) at 2.5 μm. Then, we described the device's fabrication requiring the dual combination of two semi-IPNs. In order to favor the adhesion between them, we chose a whole system based on an NBR/PEO/PEDOT semi-IPN in which the EDOT is polymerized under the same conditions as previously. The junction was ensured by the PEO partner serving as binder between the two semi-IPNs. Then, after the addition of an electrolyte (LiClO4 0.1 M/PC) to complete the device elaboration, it was possible to electrochemically switch the system and to observe NIR optical modulation with a promising contrast up to Δ%R=14% at 2.5 μm. The optical properties were also measured in the middle infrared region: the contrasts were Δ%R3–5 μm=18% and Δ%R8–12 μm=17% in the integrated bands II (3–5 μm) and III (8–12 μm), respectively.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Conducting polymers and applications · Organic Electronics and Photovoltaics · Advanced Sensor and Energy Harvesting Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (35)

Show source-provided references
1. Skotheim · 2007
2. Infrared emittance modulation devices using electrochromic crystalline tungsten oxide, polymer conductor, and nickel oxide10.1016/S0040-6090(99)00439-3 ↗
3. Infrared reflectance modulation in tungsten oxide based electrochromic devices10.1016/S0013-4686(01)00374-7 ↗
4. Flexible electrochromic reflectance device base don tungsten oxide for infrared emissivity control10.1063/1.1430543 ↗
6. Color control in π - conjugated organic polymers for use in electrochromic devices10.1021/cr900129a ↗
7. Microporous patterned electrodes for color-matched electrochromic polymer displays10.1021/cm049951s ↗
8. A. poly(34-alkylenedioxythiophene) electrochromic variable omptical attenuator with near-infrared reflectivity tuned independently of the visible region10.1002/adfm.200601145 ↗
9. Chandrasekhar · Proc. SPIE · 1995 · 169 · 2528
10. Wide band electrochromic displays based on thin conducting polymer films10.1016/S0013-4686(01)00392-9 ↗
11. Combined visible and infrared electrochromism using dual polymer devices10.1002/1521-4095(200105)13:9<634::AID-ADMA634>3.0.CO;2-3 ↗
12. Self-supported semi-interpenetrating polymer networks for new design of electrochromic devices10.1016/j.electacta.2007.12.087 ↗
13. Electroactive polymers with semi-IPN architectures for electrochromic devices10.1080/15421401003726980 ↗
14. New prospects in the conception of IR electro-tunable devices: the use of conducting semi-interpenetrating polymer network architecture10.1021/cm100736y ↗
15. 1991
16. Long-life air working conducting semi-IPN/ionic liquid based actuator10.1016/j.synthmet.2003.10.005 ↗
17. Synthesis and characterization of conducting interpenetrating polymer networks for new actuators10.1016/j.polymer.2005.03.103 ↗
18. Long-life air working semi-IPN/ionic liquid: new precursor of artificial muscles10.1080/15421400500377453 ↗
19. Conducting IPN actuators: from polymer chemistry to actuator with linear actuation10.1016/j.synthmet.2006.09.012 ↗
20. Network structure organic photovoltaic device10.1016/j.cap.2005.04.030 ↗
21. Synthesis and characterization of p and n dopable interpenetrating polymer networks for organic photovoltaic devices10.1016/j.tsf.2007.12.126 ↗
22. High ionic conductivity and mechanical strength of solid polymer electrolytes based on NBR/ionic liquid and its application to an electrochemical actuator10.1016/j.snb.2007.05.032 ↗
23. Ciesielsky · 1999
24. Conductive modifications of polymers with polypyrroles and polythiophenes10.1016/0379-6779(91)91506-6 ↗
25. Poly(3,4-ethylenedioxythiophene) and its derivatives: past, present, and future10.1002/(SICI)1521-4095(200004)12:7<481::AID-ADMA481>3.0.CO;2-C ↗
26. Electrochemistry of poly(3,4-alkylenedioxythiophene) derivatives10.1002/adma.200300376 ↗
27. Synthesis and characterization of a composite containing poly(3-methylthiophene) and nitrilic rubber10.1016/0032-3861(92)90421-R ↗
28. An electroactive elastomer: polyaniline/nitrile rubber10.1016/0032-3861(92)90540-D ↗
29. Physicochemical characterization of mixed conducting composites obtained by electropolymerization of pyrrole into perfluoronated ionomer gels10.1016/0379-6779(90)90081-U ↗
30. Interpenetrating networks of two conducting polymers10.1016/j.synthmet.2004.09.011 ↗
31. An electrochemically synthesized conducting semi-IPN from polypyrrole and poly(vinyl alcohol)10.1039/b201596j ↗
32. L.J. Goujon, A. Khaldi, A. Maziz, C. Plesse, G.T.M. Nguyen, P.H. Aubert, F. Vidal, C. Chevrot, D. Teyssié, Flexible solid polymer electrolytes based on nitrile butadiene rubber/poly(ethylene oxide) interpenetrating polymer networks, Macromolecules, submitted for publication.
33. Recommendations on reporting electrode potentials in nonaqueous silvents (Recommendations 1983)10.1351/pac198456040461 ↗
34. High rate capabilities Fe3O4- based Cu nano-architectured electrodes for lithium-ion battery applications10.1038/nmat1672 ↗
35. Optical reflectance studies of conducting polymers on the metal–insulator boundary10.1016/S0379-6779(96)04116-1 ↗