Investigating the impact of edge passivation on shingle solar modules
Source abstract
Abstract
This work deals with solar modules made from rectangular-shaped solar cell strips, so-called shingles, that are interconnected by overlapping one with another. For the fabrication of such modules, host solar cells are cut into several shingles resulting in unpassivated shingle cell edges and relevant recombination losses. As discussed in this work based on simulations, quantifying these losses on module level is not straightforward and is ideally done by referring to the pseudo fill factor pFF . In this context, it is shown that by passivating the cut edges of the shingles by depositing a dielectric layer, a significant pFF increase can be achieved both on shingle as well as on module level. Considering the highest respective pFF value found for modules with and without edge passivation, an increase of Δ pFF = 0.5% abs is reached. At the same time, no significant compromise of the interconnection quality is observed. These results are obtained for monofacial passivated emitter and rear cell (PERC) shingles. In short, this work is the first comprehensive analysis of experimental data on module level in the context of edge passivation. It demonstrates that the deposition of a dielectric passivation layer at the shingle's edges can boost pFF of shingle solar modules, while the current transit between the busbars of jointed shingles is not significantly hindered. • The pseudo fill factor is a well suitable quantity to compare solar modules. • Edge passivation boosts the pseudo fill factor of shingle solar modules. • Edge passivation does not reduce interconnection quality in shingle solar modules.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Silicon and Solar Cell Technologies · solar cell performance optimization · Photovoltaic System Optimization Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. 2023
2. The SPEER solar cell — simulation study of shingled bifacial PERC-technology-based stripe cells
3. Challenges and advantages for cut solar cells for shingling and half-cell modules
4. Schulte-Huxel · 2021
5. The sun is rising on conductive adhesives
6. Shingled cell interconnection: a new generation of bifacial PV-modules
7. Cell-to-module (CTM) analysis for photovoltaic modules with shingled solar cells
8. Progress in shingle interconnection based on electrically conductive adhesives at Fraunhofer ISE10.1063/5.0127455 ↗
9. Shingling technology for cell interconnection: technological aspects and process integration10.1016/j.egypro.2018.09.010 ↗
10. Electrically conductive adhesives as cell interconnection material in shingled module technology10.1063/1.5049305 ↗
11. Solar cell demand for bifacial and singulated-cell module architectures
12. PERC-based shingled solar cells and modules at Fraunhofer ISE
13. Bifacial p-type silicon shingle solar cells — the “pSPEER” concept
14. Postmetallization "passivated edge technology" for separated silicon solar cells10.1109/JPHOTOV.2019.2959946 ↗
15. TOPCon shingle solar cells: thermal laser separation and passivated edge technology10.1002/pip.3680 ↗
16. Thermal laser separation and high-throughput layer deposition for edge passivation for TOPCon shingle solar cells10.1016/j.solmat.2023.112419 ↗
17. Low-temperature high-throughput plasma-enhanced atomic layer deposition of aluminum oxide for c-Si solar cell edge passivation
18. How to assess the electrical quality of solar cell interconnection in shingle solar modules10.1002/pip.3699 ↗
19. Analyzing back contacts of silicon solar cells by Suns-Voc-measurements at high illumination densities
20. Design of shading- and hotspot-resistant shingled modules10.1002/pip.3507 ↗
21. Illumination dependence of reverse leakage current in silicon solar cells10.1109/JPHOTOV.2021.3088005 ↗
22. Computer simulation of the effects of electrical mismatches in photovoltaic cell interconnection circuits10.1016/0379-6787(88)90059-2 ↗
23. A quasi-steady-state open-circuit voltage method for solar cell characterization
24. A review and comparison of different methods to determine the series resistance of solar cells10.1016/j.solmat.2007.05.026 ↗
25. Performance of shingled solar modules under partial shading10.1002/pip.3486 ↗
26. Thermal laser separation (TLS) dicing process study — a new technology for cutting silicon solar cells for high-efficiency half-cell modules
27. 2018
28. Defect detection in photovoltaic modules using electroluminescence imaging
29. Magnetic field imaging (MFI) of solar modules
30. Magnetic field imaging (MFI) of shingle solar modules
31. Analysis of shingle interconnections in solar modules by scanning acoustic microscopy10.1063/1.5123871 ↗
32. Electrically conductive adhesive-free interconnection of shingle solar cells10.1016/j.solmat.2023.112517 ↗