journal article·2023-04Open access

Will SiO -pinholes for SiO /poly-Si passivating contact enhance the passivation quality?

Guangtao Yang, Remon Gram, Paul Procel, Can Han, Zhirong Yao, Manvika Singh, Yifeng Zhao, Luana Mazzarella, Miro Zeman, Olindo Isabella

Abstract

Passivating contacts based on poly-Si have enabled record-high c-Si solar cell efficiencies due to their excellent surface passivation quality and carrier selectivity. The eventual existence of pinholes within the ultra-thin SiOx layer is one of the key factors for carrier collection, beside the tunneling mechanism. However, pinholes are usually believed to have negative impact on the passivation quality of poly-Si passivating contacts. This work studied the influence of the pinhole density on the passivation quality of ion-implanted poly-Si passivating contacts by decoupling the pinhole generation from the dopants diffusion process by means of two annealing steps: (1) a pre-annealing step at high temperature after the intrinsic poly-Si deposition to visualize the formation of pinholes and (2) a post-annealing step for dopants activation/diffusion after ion-implantation. The pinhole density is quantified in the range of 1✕106 to 3✕108 cm2 by the TMAH selective etching approach. The passivation quality is discussed with respect to the pinhole density and the post-annealing thermal budget (TB) for dopants diffusion. The study shows that a moderate pinhole density does not induce doping profile variations that can be detectable by the coarse spatial resolution of ECV measurements. It is surprising that the existence of pinholes in a moderate density within our thickness fixed SiOx layer can effectively enhance the passivation qualities for both n+ and p+ poly-Si passivating contacts. We speculate the reason is due to the enhanced field-effect passivation at the pinhole surrounding. In fact, the variation of the passivation quality depends on the balance between a strengthened field-effect passivation and an excessive local Auger recombination, being both effects induced by the higher and deeper level of dopants diffused into the c-Si surface through the pinholes.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Silicon and Solar Cell Technologies · Semiconductor materials and interfaces · Integrated Circuits and Semiconductor Failure Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (30)

Show source-provided references
1. Design rules for high-efficiency both-sides-contacted silicon solar cells with balanced charge carrier transport and recombination losses10.1038/s41560-021-00805-w ↗
2. For none, one, or two polarities—how do POLO junctions fit best into industrial Si solar cells?10.1002/pip.3201 ↗
3. Silicon-rich silicon carbide hole-selective rear contacts for crystalline-silicon-based solar cells10.1021/acsami.6b12714 ↗
4. LPCVD polysilicon passivating contact
5. Rienäcker · 2016 · 412
6. Design and application of ion-implanted polySi passivating contacts for interdigitated back contact c-Si solar cells
7. Mass production of industrial tunnel oxide passivated contacts (i-TOPCon) silicon solar cells with average efficiency over 23% and modules over 345 W10.1002/pip.3180 ↗
8. Silicon solar cell architecture with front selective and rear full area ion-implanted passivating contacts10.1002/solr.201700040 ↗
9. Development of industrial n-type bifacial TOPCon solar cells and modules
10. Improvement of the SRH bulk lifetime upon formation of n-type POLO junctions for 25% efficient Si solar cells10.1016/j.solmat.2017.05.055 ↗
11. Approaching 23% with large-area monoPoly cells using screen-printed and fired rear passivating contacts fabricated by inline PECVD10.1002/pip.3097 ↗
12. Stodolny · 2019 · 1456
13. Working principle of carrier selective poly-Si/c-Si junctions: is tunnelling the whole story?10.1016/j.solmat.2016.05.045 ↗
14. Numerical simulation of carrier-selective electron contacts featuring tunnel oxides10.1109/JPHOTOV.2015.2455346 ↗
15. Numerical simulations of IBC solar cells based on poly-Si carrier-selective passivating contacts10.1109/JPHOTOV.2019.2892527 ↗
16. An analytical approach to quantify the thermal budget in consideration of consecutive thermal process steps
17. Studying dopant diffusion from Poly-Si passivating contacts10.1016/j.solmat.2019.109978 ↗
18. Impurity gettering in polycrystalline-silicon based passivating contacts - the role of oxide stoichiometry and pinholes
19. Polysilicon emitters for silicon concentrator solar cells
20. Recombination behavior and contact resistance of n+ and p+ poly-crystalline Si/mono-crystalline Si junctions10.1016/j.solmat.2014.06.003 ↗
21. Contactless determination of current-voltage characteristics and minority-carrier lifetimes in semiconductors from quasi-steady-state photoconductance data10.1063/1.117723 ↗
22. Pinhole density and contact resistivity of carrier selective junctions with polycrystalline silicon on oxide10.1063/1.4986924 ↗
23. Deposition pressure dependent structural and optoelectronic properties of ex-situ boron-doped poly-Si/SiOx passivating contacts based on sputtered silicon10.1016/j.solmat.2020.110602 ↗
24. Adaption of basic metal – insulator – semiconductor (MIS) theory for passivating contacts within numerical solar cell
25. Phosphorus and boron diffusion in silicon under equilibrium conditions10.1063/1.1566464 ↗
26. Boron and phosphorus diffusion through an SiO2 layer from a doped polycrystalline Si source under various drive-in ambients10.1016/0038-1101(75)90117-3 ↗
27. Kale
28. Local enhancement of dopant diffusion from polycrystalline silicon passivating contacts10.1021/acsami.2c01801 ↗
29. A study on the charge carrier transport of passivating contacts10.1109/JPHOTOV.2018.2870735 ↗
30. Studying dopant diffusion from poly-Si passivating contacts10.1016/j.solmat.2019.109978 ↗