journal article·2021-09

Thermally stable MoOx hole selective contact with Al2O3 interlayer for industrial size silicon solar cells

Mike Tang Soo Kiong Ah Sen, Paula Bronsveld, Arthur Weeber

Publisher page

Abstract

So far, intrinsic hydrogenated amorphous silicon (a-Si:H(i)) has been commonly used below molybdenum oxide (MoO x) to form a good contact. An a-Si:H(i)/MoO x stack gives good surface passivation, but often results in poor carrier selectivity after exposure to slightly elevated temperatures >130 °C (Geissbühler et al., 2015) [1]. For this reason, we have investigated an alternative interface layer, a very thin Al 2O 3 tunneling layer (<2 nm), deposited by atomic layer deposition (ALD), that can provide surface passivation, higher transparency and thermal stability without affecting the hole transport across the contact. To demonstrate this new passivating contact a 6” moly-poly cell, with an Al 2O 3/MoO x stack at the front side and n -type doped polysilicon at the rear side, was made using a high- throughput spatial ALD tool, and E-beam PVD, for the Al 2O 3 and MoO x layers, respectively. This resulted in an efficiency of 18.2% with a V oc of 651 mV, a FF of 75.6% and a J sc of 36.9 mA/cm 2. A post-deposition anneal (PDA) of the thin Al 2O 3 interlayer has significant effect on the Al 2O 3 thickness, layer stoichiometry, contact selectivity, and sputtering-induced damage. Annealing at higher T PDA (350–600 °C) results in ineffective hole carrier transport and makes the stack more sensitive to ITO damage. The best performing device was, therefore, made using an Al 2O 3 layer without a PDA treatment. Moreover, we have found that this solar cell structure is thermally stable up to at least 210 °C, and even slightly improves under annealing which makes this device industrially appealing.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Silicon and Solar Cell Technologies · Thin-Film Transistor Technologies · Silicon Nanostructures and Photoluminescence

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. 22.5% efficient silicon heterojunction solar cell with molybdenum oxide hole collector10.1063/1.4928747 ↗
2. Nanocrystalline silicon emitter optimization for Si-HJ solar cells: substrate selectivity and CO2 plasma treatment effect
3. Amorphous silicon oxide window layers for high-efficiency silicon heterojunction solar cells10.1063/1.4861404 ↗
4. Low-temperature p-type microcrystalline silicon as carrier selective contact for silicon heterojunction solar cells10.1109/JPHOTOV.2019.2917550 ↗
5. Silicon heterojunction solar cell with passivated hole selective MoO x contact10.1063/1.4868880 ↗
6. Bivour · 2016
7. Origin of passivation in hole-selective transition metal oxides for crystalline silicon heterojunction solar cells10.1557/jmr.2016.453 ↗
8. 23.5%-Efficient silicon heterojunction silicon solar cell using molybdenum oxide as hole-selective contact10.1016/j.nanoen.2020.104495 ↗
9. Peter · 2016
10. Toward annealing-stable molybdenum-oxide-based hole-selective contacts for silicon photovoltaics10.1002/solr.201700227 ↗
11. Selectivity issues of MoOxbased hole contacts10.1016/j.egypro.2017.09.268 ↗
12. Silicon surface passivation by atomic layer deposited Al2O310.1063/1.2963707 ↗
13. Stability of Al2O3 and Al2O3/a- SiNx:H stacks for surface passivation of crystalline silicon10.1063/1.3264572 ↗
14. Aluminum oxide passivating tunneling interlayers for molybdenum oxide hole-selective contacts10.1109/JPHOTOV.2020.2973447 ↗
15. Ultra-thin atomic layer deposited aluminium oxide tunnel layer passivated hole-selective contacts for silicon solar cells10.1016/j.solmat.2018.11.011 ↗
16. Improving the passivation of molybdenum oxide hole-selective contacts with 1 nm hydrogenated aluminum oxide films for silicon solar cells
17. Angle-resolved x-ray photoelectron spectroscopy of ultrathin Al[sub 2]O[sub 3] films grown by atomic layer deposition10.1116/1.1507330 ↗
18. Characterization of the oxide/hydroxide surface of aluminum using X-ray photoelectron spectroscopy: a procedure for curve fitting the O 1s core level10.1002/1096-9918(200007)29:7<468::AID-SIA890>3.0.CO;2-V ↗
19. Hydrogen induced passivation of Si interfaces by Al2 O 3 films and SiO2/Al2 O3 stacks10.1063/1.3497014 ↗
20. Solar Energy Materials & Solar Cells Ef fi cient carrier-selective p- and n-contacts for Si solar cells10.1016/j.solmat.2014.05.039 ↗
21. Electron beam evaporated molybdenum oxide as hole-selective contact in 6-inch c-Si heterojunction solar cells10.1063/1.5049264 ↗
22. Implementing transparent conducting oxides by DC sputtering on ultrathin SiOx/poly-Si passivating contacts10.1016/j.solmat.2019.109960 ↗
23. Interface analysis and intrinsic thermal stability of MoOx based hole-selective contacts for silicon heterojunction solar cells10.1016/j.solmat.2019.110074 ↗
24. Bullock · 2018 · 3
25. Back-contacted silicon heterojunction solar cells: optical-loss analysis and mitigation10.1109/JPHOTOV.2015.2438641 ↗
26. Chemical and structural study of electrically passivating Al 2 O 3/Si interfaces prepared by atomic layer deposition
27. Interface and material characterization of thin Al2O3 layers deposited by ALD using TMA/H2O10.1016/S0022-3093(02)00958-4 ↗
28. Damage at hydrogenated amorphous/crystalline silicon interfaces by indium tin oxide overlayer sputtering10.1063/1.4764529 ↗
29. Analysis of lateral transport through the inversion layer in amorphous silicon/crystalline silicon heterojunction solar cells10.1063/1.4818709 ↗
31. Valence band offset and hole transport across a-SiOx (0<x<2) passivation layers in silicon heterojunction solar cells, 31st
32. Valence band offset in heterojunctions between crystalline silicon and amorphous silicon (sub)oxides (a-SiOx:H, 0 < x < 2)10.1063/1.4906195 ↗
33. Asymmetric band offsets in silicon heterojunction solar cells: impact on device performance10.1063/1.4959988 ↗