Above 10% efficient electrodeposited Cu2ZnSn(S,Se)4 solar cell achieved by modifying precursor
Source abstract
Abstract
Electrodeposition is a promising method to fabricate Cu 2ZnSn(S,Se) 4 (i.e., CZTSSe) absorber layer thanks to its many advantages such as low-cost and large-scale. However, the secondary phases and intrinsic defects in electrodeposited CZTSSe solar cells inevitably limit the photoelectric performance. Herein, two different kind of precursor films (binary-ternary selenide vs. quaternary selenide) are deliberately fabricated and the effect of these precursors on the secondary phases and intrinsic defects of CZTSSe absorber layer are investigated comprehensively. The absorber layer obtained from binary-ternary selenide precursor has a small amount of ZnSe secondary phases and Cu Sn deep defects, whereas that obtained from the quaternary selenide precursor exhibits the favorable V Cu shallow defects, which is beneficial to the efficiency improvement in CZTSSe. Based on the quaternary selenide precursor film, the CZTSSe solar cell with 10.03% total area efficiency (the active area efficiency is 10.9%) was obtained. This is the highest efficiency of CZTSSe solar cells prepared by the electrodeposition method.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Chalcogenide Semiconductor Thin Films · Quantum Dots Synthesis And Properties · Copper-based nanomaterials and applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (38)
Show source-provided references
1. The path towards a high-performance solution-processed kesterite solar cell10.1016/j.solmat.2010.11.028 ↗
2. Kesterites-a challenging material for solar cells10.1002/pip.2156 ↗
3. Optimization of DMSO-based precursor solution by H2O additive for performance enhancement of kesterite photovoltaic devices10.1016/j.solmat.2018.02.001 ↗
4. Device characteristics of CZTSSe thin-film solar cells with 12.6% efficiency10.1002/aenm.201301465 ↗
5. Cu2ZnSnS4 solar cells with over 10% power conversion efficiency enabled by heterojunction heat treatment10.1038/s41560-018-0206-0 ↗
6. Defect control for 12.5% efficiency Cu2ZnSnSe4 kesterite thin-film solar cells by engineering of local chemical environment10.1002/adma.202005268 ↗
7. Effect of solid-H2S gas reactions on CZTSSe thin film growth and photovoltaic properties of a 12.62% efficiency device10.1039/C9TA08310C ↗
8. Pure sulfide Cu2ZnSnS4 thin film solar cells fabricated by preheating an electrodeposited metallic stack10.1002/aenm.201301381 ↗
9. Electrodeposition of tin onto zinc for the electrochemical synthesis of Zn/Sn/Cu precursor stack for CZTS‐based photoconversion devices10.1002/celc.202001152 ↗
10. Compositional and interfacial modification of Cu2ZnSn(S,Se)4 thin-film solar cells prepared by electrochemical deposition10.1002/cssc.201501256 ↗
11. Improved interfacial properties of electrodeposited Cu2 ZnSn(S,Se)4 thin‐film solar cells by a facile post‐heat treatment process10.1002/pip.3332 ↗
12. In situ electrochemical treatment evoked superior grain growth for green electrodeposition-processed flexible CZTSe solar cells10.1021/acsami.1c07074 ↗
13. Cu‐Promoted reversed elemental distribution for electrochemically intermetallic diffusion improved Cu2ZnSnSe4 photovoltaic device beyond 9% efficiency10.1002/solr.201900165 ↗
14. Over 10% efficient pure CZTSe solar cell fabricated by electrodeposition with Ge doping10.1002/solr.202000059 ↗
15. An 8.7% efficiency co-electrodeposited Cu2ZnSnS4 photovoltaic device fabricated via a pressurized post-sulfurization process10.1039/C8TC05058A ↗
16. Modified back contact interface of CZTSe thin film solar cells: elimination of double layer distribution in absorber layer10.1002/advs.201700645 ↗
17. Identifying the origin of the Voc deficit of kesterite solar cells from the two grain growth mechanisms induced by Sn2+ and Sn4+ precursors in DMSO solution10.1039/D0EE03702H ↗
18. Influence of the reaction pathway on the defect formation in a Cu2ZnSnSe4 thin film10.1021/acsami.1c01307 ↗
19. Realization of 11.5% efficiency Cu2ZnSn(S,Se)4 thin‐film solar cells by manipulating the phase structure of precursor films10.1002/solr.202100216 ↗
20. Status review on the Cu2SnSe3 (CTSe) thin films for photovoltaic applications10.1016/j.solener.2020.07.095 ↗
21. Beyond 10% efficient Cu2ZnSn(S,Se)4 solar cells: effects of the introduction of SnS powder during selenization process10.1016/j.solmat.2020.110522 ↗
22. Impact of Urbach energy on open-circuit voltage deficit of thin-film solar cells10.1016/j.solmat.2020.110502 ↗
23. Origin of band-tail and deep-donor states in Cu2ZnSnS4 solar cells and their suppression through Sn-poor composition10.1021/acs.jpclett.9b03227 ↗
24. Cation substitution of solution-processed Cu2ZnSnS4 thin film solar cell with over 9% efficiency10.1002/aenm.201500682 ↗
25. Bulk and metastable defects in CuIn1-xGaxSe2 thin films using drive-level capacitance profiling10.1063/1.1633982 ↗
26. Electronic properties of the Cu2ZnSn(Se,S)4 absorber layer in solar cells as revealed by admittance spectroscopy and related methods10.1063/1.4729751 ↗
27. Determination of defect distributions from admittance measurements and application to Cu(In,Ga)Se2 based heterojunctions10.1063/1.363401 ↗
28. The role of sulfur in solution-processed Cu2ZnSn(S,Se)4 and its effect on defect properties10.1002/adfm.201201732 ↗
29. Kesterite thin-film solar cells: advances in materials modelling of Cu2ZnSnS410.1002/aenm.201100630 ↗
30. Classification of lattice defects in the kesterite Cu2ZnSnS4 and Cu2ZnSnSe4 earth-abundant solar cell absorbers10.1002/adma.201203146 ↗
31. High efficiency Cu2ZnSn(S,Se)4 solar cells with shallow LiZn acceptor defects enabled by solution‐based Li post‐deposition treatment10.1002/aenm.202003783 ↗
32. Adjusting the SnZn defects in Cu2ZnSn(S,Se)4 absorber layer via Ge4+ implanting for efficient kesterite solar cells10.1016/j.jechem.2021.02.011 ↗
33. Ag incorporation with controlled grain growth enables 12.5% efficient kesterite solar cell with open circuit voltage reached 64.2% shockley–queisser limit10.1002/adfm.202101927 ↗
34. Elemental precursor solution processed (Cu1-xAgx)2ZnSn(S,Se)4 photovoltaic devices with over 10% efficiency10.1021/acsami.7b03944 ↗
35. Thin-film solar cells: device measurements and analysis10.1002/pip.518 ↗
36. Synergistic effect of Mn on bandgap fluctuations and surface electrical characteristics in Ag-based Cu2ZnSn(S,Se)4 solar cells10.1039/D0TA10103F ↗
37. Improvement of grain growth and composition distribution of Cu2ZnSn(S,Se)4 by using chloride-based precursor solution10.1016/j.solener.2020.12.067 ↗
38. MoO2 sacrificial layer for optimizing back contact interface of Cu2ZnSn(S,Se)4 solar cells10.1109/JPHOTOV.2020.2987165 ↗