Plated metal adhesion to picosecond laser-ablated silicon solar cells: Influence of surface chemistry and wettability
Source abstract
Abstract
Abstract This study investigated the influence of UV picosecond laser fluence, used to ablate the SiNx antireflection coating for Ni/Cu/Ag plated p-type Si solar cells, on busbar and finger adhesion and cell electrical performance. Surface chemistry was characterised post-ablation and post-pre-treatment in 7:1 buffered oxide etch (BOE) using a combination of X-ray photoelectron spectroscopy and contact angle measurements. Although growth of laser-induced Si oxides increases with increasing laser fluence, these oxides are effectively removed in the BOE pre-treatment and therefore do not impact plated metal adhesion with busbar pull forces of 1.9 ± 0.7 N/mm being achieved when a laser fluence of 0.63 J/cm2 was used to ablate the busbar openings. It is also revealed that the use of high laser fluence leads to a more hydrophobic surface due to reduced residual SiNx, however the complete wetting of the ablated Si surface can be ensured by the use of surfactants in Ni plating electrolytes. Residual SiNx impacts Ni silicidation and reduces the busbar pull force to values of only 0.8 ± 0.5 N/mm when average laser fluences ≤0.45 J/cm2 are used. Finger dislodgement forces are interestingly shown not to be affected by laser fluence and presence of residual SiNx, providing an opportunity to optimise the laser ablation process separately for finger and busbar openings. Finally, it is demonstrated that the use of higher laser fluences does not impact the electrical performance of the Al back surface field cells, with open-circuit voltages of ≥637 mV and fill factors ≥80.4% being demonstrated for cells where the average laser fluence used was varied between 0.35 and 0.63 J/cm2.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Integrated Circuits and Semiconductor Failure Analysis · Silicon and Solar Cell Technologies · Thin-Film Transistor Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (69)
Show source-provided references
1. Evolution of metal plating for silicon solar cell metallisation10.1002/pip.2221 ↗
2. Review of the potential of the Ni/Cu plating technique for crystalline silicon solar cells10.3390/ma7021318 ↗
3. Interface oxides in femtosecond laser structured plated Ni-Cu-Ag contacts for silicon solar cells10.1016/j.solmat.2017.03.016 ↗
4. Metallization of Si heterojunction solar cells by nanosecond laser ablation and Ni-Cu plating10.1016/j.solmat.2016.09.021 ↗
5. Improved contact metallization for high efficiency EFG polycrystalline silicon solar cells
6. Large area copper plated silicon solar cell exceeding 19.5% efficiency10.1016/j.egypro.2012.05.008 ↗
7. A simple copper metallisation process for high cell efficiencies and reliable modules
8. Low cost metallisation based on Ni/Cu plating enabling high efficiency industrial solar cells
9. Industrial Si solar cells with Cu-based plated contacts10.1109/JPHOTOV.2015.2478067 ↗
10. Monitoring of adhesion for plated metallisation: why busbar pull tests are not sufficient10.1016/j.egypro.2016.07.110 ↗
11. 266-nm ps laser ablation for copper-plated p-type selective emitter PERC silicon solar cells10.1109/JPHOTOV.2018.2834629 ↗
12. Ultra-short pulsed laser ablation of silicon nitride layers: investigation near threshold fluence10.1016/j.apsusc.2012.10.122 ↗
13. Physical mechanisms of SiNx layer structuring with ultrafast lasers by direct and confined laser ablation10.1063/1.4914457 ↗
14. Multipulse feedback in self-organized ripples formation upon femtosecond laser ablation from silicon10.1007/s00339-010-5830-x ↗
15. High-resolution investigations of ripple structures formed by femtosecond laser irradiation of silicon10.1007/s00216-009-3342-3 ↗
16. Laser induced periodic surface structures induced by surface plasmons coupled via roughness10.1016/j.apsusc.2013.10.141 ↗
17. Rippled area formed by surface plasmon polaritons upon femtosecond laser double-pulse irradiation of silicon: the role of carrier generation and relaxation processes10.1007/s00339-013-8205-2 ↗
18. Fundamentals of ultrafast laser–material interaction10.1557/mrs.2016.274 ↗
19. Mechanisms of femtosecond LIPSS formation induced by periodic surface temperature modulation10.1016/j.apsusc.2015.09.091 ↗
20. Shifting the limits with Cu based metallisation and advanced plating technology
21. Plated nickel-copper contacts on c-si: from microelectronic processing to cost effective silicon solar cell production
22. Reliable contact formation for industrial solar cells by laser ablation and Ni/Cu plating
23. Electrical and mechanical properties of plated Ni/Cu contacts for Si solar cells10.1016/j.egypro.2015.07.104 ↗
24. Untangling the mysteries of plated metal finger adhesion: understanding the contributions from plating rate, chemistry, grid geometry, and sintering10.1109/JPHOTOV.2016.2589364 ↗
25. Pilot production of high efficient metal catalyzed textured diamond wire sawn mc-si solar cells combined with nickel-copper plated front contact processing
26. Improved metal adhesion with galvanic nickel plating to silicon solar cells10.1016/j.solmat.2016.12.012 ↗
27. The importance of surface roughness in the adhesion of electroless-plated metal in inkjet printed grooves
28. Electroless plating of nickel on silicon for fabrication of high-aspect-ratio microstructures10.1016/S0924-4247(96)01318-0 ↗
29. Impact of laser-induced oxidation on silicon wafer solar cells' performance10.1109/JPHOTOV.2016.2535243 ↗
30. Microstructure analysis of the interface situation and adhesion of thermally formed nickel silicide for plated nickel–copper contacts on silicon solar cells10.1016/j.solmat.2013.06.005 ↗
31. Electroless nickel deposition and silicide formation for advanced front side metallization of industrial silicon solar cells10.1016/j.egypro.2012.05.006 ↗
32. Easy plating—a simple approach to suppress parasitically metallized areas in front side Ni/Cu plated crystalline Si solar cells10.1109/JPHOTOV.2017.2720461 ↗
33. A simple copper metallization process for high cell efficiencies and reliable modules
34. Reliable contact formation for industrial solar cells by laser ablation and Ni/Cu plating
35. Green · 1986
36. Impact of contact integrity during thermal stress testing on degradation analysis of copper-plated silicon solar cells10.1016/j.solmat.2017.09.005 ↗
37. Etch rates for micromachining processing10.1109/84.546406 ↗
38. Etch rates for micromachining processing-part II10.1109/JMEMS.2003.820936 ↗
39. Ophir Optronics Solutions Ltd
40. Error estimation in peak-shape analysis of XPS core-level spectra using UNIFIT 2003: how significant are the results of peak fits?10.1002/sia.1925 ↗
41. 20.1%-efficient crystalline silicon solar cell with amorphous silicon rear-surface passivation10.1002/pip.641 ↗
42. Design and characterization of an adhesion strength tester for evaluating metal contacts on silicon solar cells
43. Monitoring of adhesion for plated metallisation: why busbar pull tests are not sufficient10.1016/j.egypro.2016.07.110 ↗
44. Towards a more reliable manufacturing future – automatic classification of failure modes during adhesion testing of silicon solar cells10.1016/j.solener.2018.12.004 ↗
45. Chemical, optical, vibrational and luminescent properties of hydrogenated silicon-rich oxynitride films10.1016/j.tsf.2004.07.054 ↗
46. A study on the electronic properties of SiOxNy/p-Si interface10.1007/s12633-018-9811-6 ↗
47. The low temperature catalyzed chemical vapor deposition and characterization of silicon nitride thin films10.1149/1.2069356 ↗
48. XPS and AFM study of chemical mechanical polishing of silicon nitride10.1016/S0040-6090(98)00818-9 ↗
49. Microscopic structure of the SiO2/Si interface10.1103/PhysRevB.38.6084 ↗
50. X-ray photoelectron spectroscopic characterization of ultra-thin silicon oxide films on a Mo(100) surface10.1016/0039-6028(92)90748-U ↗
51. Surface wettabiliy of nitrogen plasma-implanted silicon10.1016/j.nimb.2005.08.034 ↗
52. Adhesive and friction forces between chemically modified silicon and silicon nitride surfaces10.1021/la970367q ↗
53. Surface energy of germanium and silicon10.1149/1.2425806 ↗
54. Mandich · 2002
55. MacDermid Inc · 2002
56. In situ micro-Raman analysis and X-ray diffraction of nickel silicide thin films on silicon10.1016/j.micron.2008.03.007 ↗
57. Micro-Raman spectroscopy investigation of nickel silicides and nickel (platinum) silicides10.1149/1.1390986 ↗
58. Micro-Raman spectroscopic investigation of NiSi films formed on BF2 +-, B+- and non-implanted (100)Si substrates10.1007/s00339-002-2067-3 ↗
59. Raman study of low-temperature formation of nickel silicide layers
60. Analysis of laser-induced damage during laser ablation process using picosecond pulse width laser to fabricate highly efficient PERC cells10.1016/j.solener.2014.06.020 ↗
61. The physical mechanisms of short-pulse laser ablation10.1016/S0169-4332(99)00440-7 ↗
62. Infrared and Raman spectra of the silicon-hydrogen bonds in amorphous silicon prepared by glow discharge and sputtering10.1103/PhysRevB.16.3556 ↗
63. Structural information from the Raman spectrum of amorphous silicon10.1103/PhysRevB.32.874 ↗
64. Raman scattering from hydrogenated microcrystalline and amorphous silicon10.1088/0022-3719/15/2/019 ↗
65. Reaction kinetics of nickel/silicon multilayer films10.1063/1.99644 ↗
66. Explosive silicidation in nickel/amorphous‐silicon multilayer thin films10.1063/1.345429 ↗
67. Impact of surface topography and laser pulse duration for laser ablation of solar cell front side passivating SiNx layers10.1063/1.3493204 ↗
68. Laser ablation of SiO2 for locally contacted Si solar cells with ultra-short pulses10.1002/pip.758 ↗
69. Investigation of laser ablation on boron emitters forn-type rear-junction PERT type silicon wafer solar cells10.1002/pip.2604 ↗