journal article·2013-02

Focused ion beam assisted investigations of Al interface in polythiophene:Fullerene solar cells

Nopporn Rujisamphan, Fei Deng, Roy E. Murray, Chaoying Ni, S. Ismat Shah

Publisher page

Abstract

Abstract The aluminum (Al) electrode interface in regio-regular poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) solar cells is probed using transmission electron microscopy (TEM) techniques. A state-of-the-art TEM sample preparation including in-situ lift-out is carried out using a dual focused ion beam (FIB) on two types of devices—one without annealing and one after annealing at 120 °C for 20 min. The vertical morphology is studied by crossectional TEM. It is found that upon annealing the thickness of both the Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) PEDOT:PSS and P3HT/PCBM layers decreased significantly from 21±2 nm to 16±1 nm and 130±2 to 80±1 nm, respectively. Through bright field micrographs a mixed layer between the Al electrode and the organic active layer is clearly observed in both methods of device preparations. A nanobeam mode is utilized to collect nanobeam electron diffraction (NBD) pattern in different layers of the device. In the Al layer, discrete diffraction spots from the atomic planes are observed, indicating a single crystal structure of Al. A broad ring diffraction pattern is observed in the P3HT/PCBM layer indicated disorder in the organic layer. A mixture of diffraction spots and an amorphous-like pattern is collected from the mixed region implying diffusion of Al into the organic layer. Elemental mapping results also confirmed that upon annealing Al diffused into the organic layer. Bright field TEM images of annealed devices show a well-contacted interface between Al and the mixed layer as compared to the unannealed devices. The effect of Al contact resistance before and after annealing is studied using the vertical transmission line model (TLM). It is found that by annealing after Al evaporation, the contact resistivity decreased by 38%. The results are consistent with the observation that upon annealing Al atoms diffused into the organic layer and established a mixed region which helps to decrease the contact resistance between the Al electrode and P3HT:PCBM active layer.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Organic Electronics and Photovoltaics · Integrated Circuits and Semiconductor Failure Analysis · Force Microscopy Techniques and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (28)

Show source-provided references
1. A strong regioregularity effect in self-organizing conjugated polymer films and high-efficiency polythiophene:fullerene solar cells10.1038/nmat1574 ↗
2. High-efficiency solution processable polymer photovoltaic cells by self-organization of polymer blends10.1038/nmat1500 ↗
3. Stability of polymer solar cells10.1002/adma.201104187 ↗
4. Long-lasting flexible organic solar cells stored and tested entirely in air10.1063/1.3672222 ↗
5. Stability/degradation of polymer solar cells10.1016/j.solmat.2008.01.005 ↗
6. Influence of the exciton blocking layer on the stability of layered organic solar cells10.1016/j.jpcs.2010.11.006 ↗
7. A life cycle analysis of polymer solar cell modules prepared using roll-to-roll methods under ambient conditions10.1016/j.solmat.2010.08.020 ↗
8. Device lifetime improvement of polymer-based bulk heterojunction solar cells by incorporating copper oxide layer at Al cathode10.1063/1.3580629 ↗
9. Two-layer organic photovoltaic cell10.1063/1.96937 ↗
10. Transient absorption imaging of P3HT:PCBM photovoltaic blend: evidence for interfacial charge transfer state10.1021/jz200389b ↗
11. Charge photogeneration in organic solar cells10.1021/cr900271s ↗
12. P3HT:PCBM, best seller in polymer photovoltaic research10.1002/adma.201100792 ↗
13. Growth rate dependent trap density in polythiophene-fullerene solar cells and its implications10.1063/1.3560483 ↗
14. Oxygen doping of P3HT:PCBM blends: influence on trap states, charge carrier mobility and solar cell performance10.1016/j.orgel.2010.07.016 ↗
15. Investigation of annealing effects and film thickness dependence of polymer solar cells based on poly(3-hexylthiophene)10.1063/1.2008386 ↗
16. Thermally stable, efficient polymer solar cells with nanoscale control of the interpenetrating network morphology10.1002/adfm.200500211 ↗
17. Yao · 2007
18. Real-time investigation of crystallization and phase-segregation dynamics in P3HT:PCBM solar cells during thermal annealing10.1002/adfm.201002076 ↗
19. Nanoscale morphology of high-performance polymer solar cells10.1021/nl048120i ↗
20. Polymer Crystallization of partially miscible polythiophene/fullerene mixtures controls morphology10.1021/ma200855r ↗
21. Investigation of high-performance air-processed poly(3-hexylthiophene)/methanofullerene bulk-heterojunction solar cells10.1021/jp108886p ↗
22. Imaging the interfaces of conjugated polymer optoelectronic devices10.1002/adma.200700887 ↗
23. Growth and morphology of sputtered aluminum thin films on P3HT surfaces10.1021/am101195m ↗
24. Molecular miscibility of polymer–fullerene blends10.1021/jz101276h ↗
25. Williams · 2009
26. P3HT/PCBM bulk heterojunction solar cells: Impact of blend composition and 3D morphology on device performance10.1002/adfm.200902247 ↗
27. Real time investigation of the interface between a P3HT:PCBM layer and an Al electrode during thermal annealing10.1002/marc.200900224 ↗
28. Bulk and contact resistance in P3HT:PCBM heterojunction solar cells10.1016/j.solmat.2011.03.046 ↗