journal article·2014-11

Improved seeded directional solidification process for producing high-efficiency multi-crystalline silicon ingots for solar cells

Xiaofang Qi, Qinghua Yu, Wenhan Zhao, Xueqin Liang, Jun Zhang, Lijun Liu

Publisher page

Abstract

Abstract We proposed an improved process design for the industrial mc-Si seeded directional solidification process to produce high-quality multi-crystalline silicon ingots for high-efficiency solar cells. A transient global model of heat transfer was employed to investigate the effects of the process design parameters on the melt–crystal interface shape, thermal field, and thermal stress distribution in the solidified silicon ingot during the solidification process. Ingot casting experiments were carried out and the solar cell performance was measured. The results show that the melt–crystal interface shape in the improved process design remains convex during almost the whole solidification process, and the thermal stress level at the bottom of the solidified ingots is significantly lower than in the original process design. Based on the experimental results, the quality of grown silicon ingots and the conversion efficiency of solar cells were analyzed. The shadow region present in the silicon ingot produced with the original process design disappears and the morphology of the ingot is improved with a more homogeneous distribution of grain orientation using the improved process design. The average yield rate of the solidified silicon ingot is 8.18% higher with the improved process design. The average conversion efficiency of solar cells is higher with the improved process design (17.59%) than with the original process design (17.48%).
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Silicon and Solar Cell Technologies · Silicon Nanostructures and Photoluminescence · Solidification and crystal growth phenomena

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (19)

Show source-provided references
1. Optimization and modeling of photovoltaic silicon crystallization processes, selected topics on crystal growth10.1063/1.3476230 ↗
2. Seed-assisted cast quasi-single crystalline silicon for photovoltaic application: towards high efficiency and low cost silicon solar cells10.1016/j.solmat.2012.02.024 ↗
3. Influence of an insulation partition on a seeded directional solidification process for quasi-single crystalline silicon ingot for high-efficiency solar cells10.1016/j.solmat.2012.01.024 ↗
4. Local design of the hot-zone in an industrial seeded directional solidification furnace for quasi-single crystalline silicon ingots10.1016/j.jcrysgro.2012.07.039 ↗
5. Optimizing seeded casting of mono-like silicon crystals through numerical simulation10.1016/j.jcrysgro.2012.04.033 ↗
6. An enhanced cooling design in directional solidification for high quality multi-crystalline solar silicon10.1016/j.jcrysgro.2011.12.045 ↗
7. Arrangement of dendrite crystals grown along the bottom of Si ingots using the dendritic casting method by controlling thermal conductivity under crucibles10.1016/j.jcrysgro.2011.01.069 ↗
8. High-quality multi-crystalline silicon (mc-Si) grown by directional solidification using notched crucibles10.1016/j.jcrysgro.2010.10.090 ↗
9. Characterization of high-efficiency multi-crystalline silicon in industrial production10.1016/j.solmat.2013.06.013 ↗
10. Seed-assisted growth of high-quality multi-crystalline silicon in directional solidification10.1016/j.jcrysgro.2013.09.051 ↗
11. Silicon ingot casting: process development by numerical simulations10.1016/S0927-0248(01)00153-2 ↗
12. Analysis of 3D unsteady melt flow and crystallization front geometry during a casting process for silicon solar cells10.1016/j.jcrysgro.2006.12.050 ↗
13. Numerical studies on a type of mechanical stirring in directional solidification method of multicrystalline silicon for photovoltaic applications10.1016/j.jcrysgro.2012.01.011 ↗
14. Thermo-mechanical analysis of the ingot-crucible contact during multi-crystalline silicon ingot casting10.1016/j.jcrysgro.2010.10.212 ↗
15. Transient analysis of the cooling process and influence of bottom insulation on the stress in the multicrystalline silicon ingot10.1002/crat.201300123 ↗
16. Modeling and improvement of silicon ingot directional solidification for industrial production systems10.1016/j.solmat.2009.04.001 ↗
17. 3D dynamic mesh numerical model for multi-crystalline silicon furnaces10.1016/j.jcrysgro.2006.12.075 ↗
18. Heat transfer in an industrial directional solidification furnace with multi-heaters for silicon ingot10.1016/j.jcrysgro.2013.01.053 ↗
19. Study on thermal stress in a silicon ingot during a unidirectional solidification process10.1016/j.jcrysgro.2008.07.027 ↗