A laser induced forward transfer process for selective boron emitters
Source abstract
Abstract
Abstract In this work, we present a novel technological approach to form highly boron-doped selective emitters. The selective emitters are formed by using a Laser Induced Forward Transfer Doping (DLIFT) process, which allows precise adjustment of the doping profile by tuning the laser parameters and choosing an appropriate doping source. Surface dopant concentrations of up to Ns≈1×1021 cm−3 were achieved by using DLIFT. Subsequent BBr3 tube furnace diffusion was performed to form a low surface concentration (Ns≈1×1019 cm−3) homogeneous emitter. In comparison to the conventionally applied BBr3 tube diffusion, an increase in open circuit voltage of up to 6 mV is predicted based on the photoluminescence measurements performed after passivation, screen-printing and firing processes. Simulations suggest that this voltage gain is most possibly due to a lower emitter saturation current density (j0e) of the highly doped DLIFT samples compared to the BBr3 diffusion samples. Moreover, it is observed that the laser-induced defects are reduced successfully after a subsequent boron tribromide (BBr3) tube diffusion, which is used to form the homogeneous emitter after the DLIFT process. The micro Raman spectroscopy results indicated that the compressive stress of −200 MPa in the silicon crystal lattice after DLIFT process is released by the subsequent BBr3 tube diffusion. These results demonstrate that the DLIFT process in combination with the conventionally applied BBr3 tube diffusion can be an effective approach to form selective boron emitters in high efficiency n-type crystalline silicon (c-Si) solar cells.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Silicon and Solar Cell Technologies · Integrated Circuits and Semiconductor Failure Analysis · Silicon Nanostructures and Photoluminescence
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (82)
Show source-provided references
1. Efficient Si solar cells by laser photochemical doping10.1063/1.92280 ↗
2. 18.9% efficient full area laserdoped silicon solar cell10.1063/1.3232208 ↗
3. Laser isolation of shunted regions in industrial solar cells10.1002/pip.766 ↗
4. M.Woelki, J.H.Scaroni, Writing on Silicon Wafers (US 5329090 A), 12 Jul, 1994.
5. Parametric study to improve laser hole drilling process10.1016/S0924-0136(97)00076-9 ↗
6. Deep junction laser doping for contacting buried layers in silicon solar cells10.1016/j.solmat.2013.02.011 ↗
7. Laser-fired rear contacts for crystalline silicon solar cells10.1002/pip.422 ↗
8. Contact formation and recombination at screen-printed local aluminum-alloyed silicon solar cell base contacts10.1109/TED.2011.2161089 ↗
9. Focus alignment method for laser manufacturing at sub-micron positional accuracy10.1016/j.phpro.2012.10.103 ↗
10. Incorporation of deep laser doping to form the rear localized back surface field in high efficiency solar cells10.1016/j.solmat.2014.06.037 ↗
11. Design, fabrication and characterisation of a 24.4% efficient interdigitated back contact solar cell10.1002/pip.2556 ↗
12. H.Somberg, Efficient semicrystalline solar cells using rapid thermal processing for emitter tailoring, in: 9th. EU PVSEC, Freiburg, Germany, 1989.
13. Impact of boron doping profiles on the specific contact resistance of screen printed Ag-Al contacts on silicon10.1016/j.solmat.2015.04.039 ↗
14. Influence of emitter properties on contact formation to p+ silicon10.1016/j.egypro.2013.07.338 ↗
15. Towards understanding the characteristics of Ag–Al spiking on boron-doped silicon for solar cells10.1016/j.solmat.2015.11.032 ↗
16. R.Kopecek, T.Buck, J.Libal, R.Petres, I.Röver, K.Wambach, P.Fath, Large area n-type multicrystalline silicon solar cells with B-emitter: efficiencies exceeding 14%, in: 15th IPSEC, 2005.10.1109/WCPEC.2006.279319 ↗
17. V. Mikhitaryan, A.Kravtchenko, S.Garanzha, O.Tchaplygina, S.Vityuk, N.Schalko, Lead free silver aluminum paste forcrystalline silicon solar cells, in: 21st EU PVSEC, Dresden (Germany), 2006.
18. S.Fritz, J.Engelhardt, S.Ebert, G.Hahn, Contacting boron emitters on n‐type silicon solar cells with aluminium‐free silver screen‐printing pastes, Physicastatus solidi (RRL)-Rapid Research Letters, 2016.10.1002/pssr.201510443 ↗
19. Effects of current-injection firing with Ag paste in a boron emitter
20. U. Besi-Vetrella, L. Pirozzi, E. Salza, G. Ginocchietti, F. Ferrazza, L. Ventura, and J. C. Muller, Large area screen printed silicon solar cells with selective emitter made by laser overdoping and RTA spin-on glasses, in: Proceedings of the 26th IEEE Photovoltaic Specialists Conference, Anaheim (EEUU), 1997.
21. S.Fernandez-Robledo, U.Jäger, E.Lohmüller, J.Nekarda, Laser Doping from Borosilicate Glass for Metallization of Boron Emitters, in: 28th EU PVSEC Paris (France), 2013.
22. Selective laser doping from boron silicate glass10.1016/j.egypro.2012.07.093 ↗
23. S.Kluska, A.Rodofili, K.Mayer, C.Fleischmann, F.Granek, S.W.Glunz, Analysis of local boron dopings formed with LCP, in: 25th EU PVSEC, Valencia (Spain), 2010.
24. S.R.Wenham, M.A.Green, Self Aligning Method for Forming a Selective Emitter and Metallization in a Solar Cell, US 6429037 B1, 2002.
25. Metal deposition from a supported metal film using an excimer laser10.1063/1.337287 ↗
26. Bäuerle · 2013
27. Low temperature laser metallization for silicon solar cells10.1016/j.egypro.2011.06.181 ↗
28. R.Ferré, R.Gogolin, J.Müller, N.-P.Harder, M.Kessler, C.Mader, P.Giesel, T.Neubert, R.Brendel, Laser transfer doping using amorphous silicon, in: 26th EU PVSEC, Hamburg (Germany), 2011.
29. Laser induced forward transfer for front contact improvement in silicon heterojunction solar cells10.1016/j.apsusc.2014.09.172 ↗
30. Current losses at the front of silicon heterojunction solar cells10.1109/JPHOTOV.2011.2174967 ↗
31. Diffusion coefficients of impurities in silicon melt10.1143/JJAP.2.212 ↗
32. D.Stüwe, R.Keding, A.Salim, M.Jahn, R.Efinger, F.Clement, B.Thaidigsmann, J.G.Korvink, C.Tueshaus, S.Barth, O.Doll, D.Biro, Inkjet-printed diffusion sources, in: 29th EU PVSEC, Amsterdam (The Netherlands), 2014, pp. 976–979.
33. High-speed wavelength-swept semiconductor laser with a polygon-scanner-based wavelength filter10.1364/OL.28.001981 ↗
34. W.-Y.Oh, B.J.Vakoc, G.J.Tearney, B.E.Bouma, Apparatus and Method for Utilization of a High-speed Optical Wavelength Tuning Source (US 20100254415 A1), 07 Oct, 2010.
35. C.Myers, S.Platter, Heat Treating Process for Semiconductor Fabrication, US 3723053 A, 27 Mar, 1973.
36. Selective laser annealing10.1063/1.91365 ↗
37. J.Narayan, C.W.White, R.T.Young, Method for Making Defect-free Zone by Laser-Annealing of Doped Silicon (US4181538 A), 01Jan, 1980.
38. J.Jeurink, J.Seiffe, M.Hofmann, J.Rentsch, R.Preu, Plasma deposition of amorphous silicon dopant sources, in: 26th EU PVSEC, Hamburg (Germany), 2011.
39. Industrial large scale silicon nitride deposition on photovoltaic cells with linear microwave plasma sources
40. S.Werner, E.Lohmüller, U.Belledin, A.H.G.Vlooswijk, R.C.G.Naber, S.Mack, A.Wolf, Optimization of BBr3 diffusion processes for n-type silicon solar cells, in: 31st EU PVSEC, Hamburg, Germany, 2015.
41. Measurement of sheet resistivities with the four‐point probe10.1002/j.1538-7305.1958.tb03883.x ↗
42. Capacitance-voltage profiling and the characterisation of III–V semiconductors using electrolyte barriers10.1088/0268-1242/1/1/002 ↗
43. Quantitative carrier lifetime measurement with micron resolution10.1063/1.3462433 ↗
44. Optimizing micro Raman and PL spectroscopy for solar cell technological assessment10.1016/j.egypro.2012.07.053 ↗
45. Voltage calibration of luminescence images of silicon solar cells10.1063/1.4862400 ↗
46. Evaluation of implantation annealing for highly-doped selective boron emitters suitable for screen-printed contacts10.1016/j.solmat.2013.06.040 ↗
47. Analysis of laser doping of silicon using different boron dopant sources10.1016/j.apsusc.2014.01.071 ↗
48. Diffusion of boron in silicon during post‐implantation annealing10.1063/1.348740 ↗
49. Large enhancement of boron solubility in silicon due to biaxial stress. applied physics letters10.1063/1.1484557 ↗
50. Physical processes associated with the deactivation of dopants in laser annealed silicon10.1063/1.1481974 ↗
51. Redistribution of acceptor and donor impurities during thermal oxidation of silicon10.1063/1.1713825 ↗
52. Time scale effects in laser material removal: a review10.1007/s00170-003-2026-y ↗
53. Structural and electronic characterization of 355nm laser-crystallized silicon: interplay of film thickness and laser fluence10.1063/1.4872464 ↗
54. Physical mechanisms of transient enhanced dopant diffusion in ion-implanted silicon10.1063/1.364452 ↗
55. The influence of diffusion-induced dislocations on high efficiency silicon solar cells10.1109/TED.2005.863535 ↗
56. Statistics of the recombinations of holes and electrons10.1103/PhysRev.87.835 ↗
57. Application of photoluminescence characterization to the development and manufacturing of high-efficiency silicon solar cells10.1063/1.2398724 ↗
58. Auger coefficients for highly doped and highly excited silicon10.1063/1.89694 ↗
59. Spatially resolved series resistance of silicon solar cells obtained from luminescence imaging10.1063/1.2709630 ↗
60. A.Luft, U.Franz, L.Emsermann, J.Kaspar, A study of thermal and mechanical effects on materials induced by pulsed laser drilling, Appl. Phys., vol. 63, pp. 93–101.10.1007/BF01567635 ↗
61. M.F.Zaeh, G.Branner, Investigations on residual stresses and deformations in selective laser melting, Prod. Eng., vol. 4, pp. 35–4510.1007/s11740-009-0192-y ↗
62. Fundamentals of silicon material properties for successful exploitation of strain engineering in modern CMOS manufacturing10.1109/TED.2006.872912 ↗
63. Boron and phosphorus diffusion in strained and relaxed Si and SiGe10.1063/1.1602564 ↗
64. Silicon as a mechanical material10.1109/PROC.1982.12331 ↗
65. Residual stress and mechanical properties of boron-doped p+-silicon films10.1016/0924-4247(90)87048-N ↗
66. An insight into dislocation density reduction in multicrystalline silicon10.1016/j.solmat.2016.03.040 ↗
67. PC1Dmod 6.2. Improved simulation of c-Si devices with updates on device physics and user interface10.1016/j.egypro.2016.07.010 ↗
68. Models for numerical device simulations of crystalline silicon solar cells. A review10.1007/s10825-011-0367-6 ↗
69. Improved quantitative description of Auger recombination in crystalline silicon10.1103/PhysRevB.86.165202 ↗
70. Finite-temperature full random-phase approximation model of band gap narrowing for silicon device simulation10.1063/1.368545 ↗
71. Hydrogen passivation of silicon surfaces: a classical molecular-dynamics study10.1103/PhysRevB.57.13295 ↗
72. Hydrogen diffusion along passivated grain boundaries in silicon ribbon10.1063/1.94797 ↗
73. Analytical modeling of industrial-related silicon solar cells10.1109/JPHOTOV.2013.2281105 ↗
74. A review and comparison of one- and two-dimensional simulations of solar cells featuring selective emitters10.1109/JPHOTOV.2012.2199083 ↗
75. J.Benick, B.Hoex, G.Dingemans, W.M.M.Kessels, A.Richter, M.Hermle, S.W.Glunz, High-efficiency n-type silicon solar cells with front side boron emitter, in: 24th EU PVSEC, Hamburg (Germany), 2009.
76. N-type single-crystalline Si solar cells: front side metallization for solar cells reaching 20% efficiency10.1016/j.solmat.2016.05.027 ↗
77. The recombination Parameter J010.1016/j.egypro.2014.08.073 ↗
78. Numerical Modelling of silicon p+ emitters passivated by a PECVD AlOx/SiNx stack10.1016/j.egypro.2013.05.046 ↗
79. Influence of the front surface passivation quality on large area n-type silicon solar cells with Al-alloyed rear emitter10.1016/j.egypro.2011.06.170 ↗
80. A.Cuevas, M.Stuckings, J.Lau, M.Petravic, The recombination velocity of boron diffused silicon surfaces, in:14th EU PVSEC, Barcelona (Spain), 1997.
81. Reverse bias behavior of diffused and screen-printed n-type Cz-Si solar cells10.1109/JPHOTOV.2014.2355034 ↗
82. E.Lohmüller, S.Werner, B.Thaidigsmann, N.Wöhrle, F.Clement, D.Biro, The HIP-MWT solar cell concept on n-type silicon and metallization-induced voltage losses, in: 29th EU PVSEC, Amsterdam (Netherlands), 2014, pp. 635–641.