Metal nano-grids for transparent conduction in solar cells
Source abstract
Abstract
Abstract A general procedure for predicting metal grid performance in solar cells was developed. Unlike transparent conducting oxides (TCOs) or other homogeneous films, metal grids induce more resistance in the neighbor layer. The resulting balance of transmittance, neighbor and grid resistance was explored in light of cheap lithography advances that have enabled metal nano-grid (MNG) fabrication. The patterned MNGs have junction resistances and degradation rates that are more favorable than solution-synthesized metal nanowires. Neighbor series resistance was simulated by the finite element method, although a simpler analytical model was sufficient in most cases. Finite-difference frequency-domain transmittance simulations were performed for MNGs with minimum wire width (w) of 50 nm, but deviations from aperture transmittance were small in magnitude. Depending on the process, MNGs can exhibit increased series resistance as w is decreased. However, numerous experimental reports have already achieved transmittance-MNG sheet resistance trade-offs comparable to TCOs. The transmittance, neighbor and MNG series resistances were used to parameterize a grid fill factor for a solar cell. This new figure of merit was used to demonstrate that although MNGs have only been employed in low efficiency solar cells, substantial gains in performance are predicted for decreased w in all high efficiency absorber technologies.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Nanowire Synthesis and Applications · Thin-Film Transistor Technologies · ZnO doping and properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (100+)
Show source-provided references
1. Metal nanowire networks: the next generation of transparent conductors10.1002/adma.201402710 ↗
2. A mechanical assessment of flexible optoelectronic devices10.1016/S0040-6090(01)01138-5 ↗
3. Thermal degradation of indium‐tin‐oxide/p‐silicon solar cells10.1063/1.327356 ↗
4. Plasma damage-free sputtering of indium tin oxide cathode layers for top-emitting organic light-emitting diodes10.1063/1.1923182 ↗
5. Transparent conducting oxides for electrode applications in light emitting and absorbing devices10.1016/j.spmi.2010.08.011 ↗
6. Quantitative analyses of damp-heat-induced degradation in transparent conducting oxides10.1016/j.solmat.2013.12.014 ↗
7. H.M. Lemire, K.A. Peterson, S. Sprawls, K. Singer, I.T. Martin, R.H. French, Degradation of transparent conductive oxides: mechanistic insights across configurations and exposures, in, pp. 882502-882502-882508, 2013.
8. F.J. Pern, R. Noufi, Stability of CIGS solar cells and component materials evaluated by a step-stress accelerated degradation test method, in, pp. 84720J-84720J-84714, 2012.
9. Failure of silver nanowire transparent electrodes under current flow10.1186/1556-276X-8-235 ↗
10. Corrosion at the nanoscale: the case of silver nanowires and nanoparticles10.1021/cm051532n ↗
11. Feldman · 2008 · 103
12. Size-dependent melting point of noble metals10.1016/S0254-0584(03)00201-3 ↗
13. The effect of light and humidity on the stability of silver nanowire transparent electrodes10.1039/C5RA02722E ↗
14. Time to failure modeling of silver nanowire transparent conducting electrodes and effects of a reduced graphene oxide over layer10.1016/j.solmat.2015.08.005 ↗
15. Stability of silver nanowire based electrodes under environmental and electrical stresses10.1039/C4NR06783E ↗
16. Size-dependent melting point depression of nanostructures: nanocalorimetric measurements10.1103/PhysRevB.62.10548 ↗
17. Comparing the fundamental physics and device performance of transparent, conductive nanostructured networks with conventional transparent conducting oxides10.1002/aenm.201100608 ↗
18. Green · 1982
19. Double screen printed metallization of crystalline silicon solar cells as low as 30 μm metal line width for mass production10.1016/j.solmat.2012.01.018 ↗
20. Nanopatterned metallic films for use as transparent conductive electrodes in optoelectronic devices10.1021/nl1011239 ↗
21. Theoretical comparison of optical and electronic properties of uniformly and randomly arranged nano-porous ultra-thin layers10.1364/OE.23.017860 ↗
22. A broadband plasmonic enhanced transparent conductor10.1039/c4nr01792g ↗
23. Direct imprinting of thermally reduced silver nanoparticles via deformation-driven ink injection for high-performance, flexible metal grid embedded transparent conductors10.1039/C5RA09431C ↗
24. Transparent conducting silver nanowire networks10.1021/nl301045a ↗
25. Uniform self-forming metallic network as a high-performance transparent conductive electrode10.1002/adma.201302950 ↗
26. A new architecture for transparent electrodes: relieving the trade-off between electrical conductivity and optical transmittance10.1002/adma.201100419 ↗
27. A transparent electrode based on a metal nanotrough network10.1038/nnano.2013.84 ↗
28. Uniform and ordered copper nanomeshes by microsphere lithography for transparent electrodes10.1021/nl5003075 ↗
29. Transparent metal network with low haze and high figure of merit applied to front and back electrodes in semitransparent ITO-free polymer solar cells10.1002/ente.201500014 ↗
30. Large-area soft-imprinted nanowire networks as light trapping transparent conductors10.1038/srep11414 ↗
31. Indium-free, highly transparent, flexible Cu2O/Cu/Cu2O mesh electrodes for flexible touch screen panels10.1038/srep16838 ↗
32. Fabrication of oxidation-resistant metal wire network-based transparent electrodes by a spray-roll coating process10.1021/acsami.5b08171 ↗
33. Silver front electrode grids for ITO-free all printed polymer solar cells with embedded and raised topographies, prepared by thermal imprint, flexographic and inkjet roll-to-roll processes10.1039/c2nr31508d ↗
34. High-durable AgNi nanomesh film for a transparent conducting electrode10.1002/smll.201400911 ↗
35. Identification and design principles of low hole effective mass p-type transparent conducting oxides10.1038/ncomms3292 ↗
36. Metal–insulator–semiconductor nanowire network solar cells10.1021/acs.nanolett.6b00949 ↗
37. Random mesh-like Ag networks prepared via self-assembled Ag nanoparticles for ITO-free flexible organic solar cells10.1016/j.solmat.2016.04.056 ↗
38. C.R. Fang, J.R. Hauser, A two dimensional analysis of sheet resistance and contact resistance effects in solar cells, in: Proceedings of the 13th Photovoltaic Specialists Conference, pp. 1306–1311, 1978.
39. The distributed series resistance problem in solar cells10.1016/0379-6787(84)90110-8 ↗
40. I.L. Eisgruber, J.R. Sites, Effect of thin film module geometry on solar cell current-voltage analysis, in: Photovoltaic Energy Conversion, 1994, Conference Record of the Twenty Fourth. IEEE Photovoltaic Specialists Conference −1994, 1994 IEEE in: Proceedings of the First World Conference on, pp. 271–274, 1994.
41. Theoretical analysis of the series resistance of a solar cell10.1016/0038-1101(67)90159-1 ↗
42. The effect of the front contact sheet resistance on solar cell performance10.1016/j.solmat.2009.03.028 ↗
43. Distributed series resistance effects in solar cells10.1109/T-ED.1982.20784 ↗
44. Analytical model for the design principle of large-area solar cells10.1016/j.solmat.2011.08.016 ↗
45. A.W. Haas, J.R. Wilcox, J.L. Gray, R.J. Schwartz, Numerical modeling of loss mechanisms resulting from the distributed emitter effect in concentrator solar cells, in: Photovoltaic Specialists Conference (PVSC), 2009 34th IEEE, pp. 002244–002249, 2009.
46. Y. Yang, G. Xu, K. Zhang, X. Zhang, H. Shen, P.P. Altermatt, P.J. Verlinden, Z. Feng, Analysis of series resistance of industrial crystalline silicon solar cells by numerical simulation and analytical modeling, in: Proceedings of the 28th European Photovoltaic Solar Energy Conference and Exhibition, pp. 1558–1561, 2013.
47. Analytical models for the series resistance of selective emitters in silicon solar cells including the effect of busbars10.1002/pip.2403 ↗
48. On the collection of photocurrent in solar cells with a contact grid10.15407/spqeo2.02.042 ↗
49. Calculation of the resistance of the diffused top layer in a photovoltaic cell10.1016/0379-6787(86)90045-1 ↗
50. Indium-Tin-Oxide transparent conducting coatings on silicon solar cells and their “figure of merit”10.1016/0165-1633(81)90038-1 ↗
51. Sheet resistance component of series resistance in a solar cell as a function of grid geometry10.1016/0038-1101(77)90103-4 ↗
52. Solution‐grown cadmium sulfide films for photovoltaic devices10.1149/1.2221246 ↗
53. Chemical bath deposition of CdS thin films: electrochemical in situ kinetic studies10.1149/1.2068984 ↗
54. Characterization of CdS thin films grown by chemical bath deposition using four different cadmium sources10.1016/j.tsf.2008.01.004 ↗
55. Effect of the cadmium ion source on the structural and optical properties of chemical bath deposited CdS thin films10.1016/S1293-2558(00)80073-4 ↗
56. Numerical modeling of CdS/CdTe and CdS/CdTe/ZnTe solar cells as a function of CdTe thickness10.1016/j.solmat.2007.04.006 ↗
57. Fonash · 2012
58. M. Gloeckler, A.L. Fahrenbruch, J.R. Sites, Numerical modeling of CIGS and CdTe solar cells: setting the baseline, in: Photovoltaic Energy Conversion, 2003. in: Proceedings of the 3rd World Conference on, pp. 491–494, 2003.
59. Effects of junction parameters on Cu(In,Ga)Se2 solar cells10.1016/j.jpcs.2007.07.118 ↗
60. Prospects of novel front and back contacts for high efficiency cadmium telluride thin film solar cells from numerical analysis10.1016/j.solmat.2010.02.042 ↗
61. Simulation of CIGS thin film solar cells using AMPS-1D
62. Scheer · 2011
63. Song · 2006 · 142
64. R. Kamada, T. Yagioka, S. Adachi, A. Handa, K.F. Tai, T. Kato, H. Sugimoto, New world record Cu(In,Ga)(Se,S)2 thin film solar cell efficiency beyond 22%, in: Photovoltaic Specialist Conference (PVSC), 2016 IEEE 43rd, Portland, OR, pp. in press, 2016.10.1109/PVSC.2016.7749822 ↗
65. Effects of heavy alkali elements in Cu(In,Ga)Se2 solar cells with efficiencies up to 22.6%10.1002/pssr.201600199 ↗
66. Size effects in the electrical resistivity of polycrystalline nanowires10.1103/PhysRevB.61.14215 ↗
67. Alteration of Cu conductivity in the size effect regime10.1116/1.1642639 ↗
68. A combined graphene and periodic Au nanograte structure: fundamentals and application as a flexible transparent conducting film in a flexible organic photovoltaic cell10.1016/j.carbon.2016.03.035 ↗
69. Series resistance and optimum grid design for a thin film solar cell of rectangular shape10.1016/0379-6787(84)90005-X ↗
70. Effect of geometric lattice design on optical/electrical properties of transparent silver grid for organic solar cells10.1364/OE.22.026891 ↗
71. Evaluation of ink-jet printed current collecting grids and busbars for ITO-free organic solar cells10.1016/j.solmat.2012.04.039 ↗
72. Electrohydrodynamic NanoDrip printing of high aspect ratio metal grid transparent electrodes10.1002/adfm.201503705 ↗
73. Low-cost facile fabrication of flexible transparent copper electrodes by nanosecond laser ablation10.1002/adma.201500098 ↗
74. Large-area fabrication of periodic arrays of nanoholes in metal films and their application in biosensing and plasmonic-enhanced photovoltaics10.1002/adfm.201001262 ↗
75. Transparent conductor based on aluminum nanomesh10.1088/1742-6596/541/1/012027 ↗
76. Fabrication of large area, high-performance, transparent conducting electrodes using a spontaneously formed crackle network as template10.1002/admi.201400090 ↗
77. Bio-inspired networks for optoelectronic applications10.1038/ncomms6674 ↗
78. Solar cell conducting grid structure10.1016/0038-1101(76)90009-5 ↗
79. Optimization of tapered busses for solar cell contacts10.1016/0038-092X(79)90197-X ↗
80. H.B. Serreze, Optimizing solar cell performance by simultaneous consideration of grid pattern design and interconnect configuration, in: Proceedings of the 13th Photovoltaic Specialists Conference, pp. 609–614, 1978.
81. Substrate effects on the transmittance of 1D metal grid transparent electrodes10.1364/OE.22.019021 ↗
82. FDTD simulation of transmittance characteristics of one-dimensional conducting electrodes10.1364/OE.22.006269 ↗
83. Towards understanding the difference of optoelectronic performance between micro- and nanoscale metallic layers10.1364/OME.6.002655 ↗
84. A two-dimensional nanopatterned thin metallic transparent conductor with high transparency from the ultraviolet to the infrared10.1063/1.4765341 ↗
85. Modulation of optical transmittance and conductivity by the period, linewidth and height of Au square mesh electrodes10.1364/OE.23.000A62 ↗
86. Light absorption mechanism in organic solar cells with hexagonal lattice nanohole aluminum transparent electrodes10.1088/2040-8978/17/8/085901 ↗
87. Optical properties of metallic films for vertical-cavity optoelectronic devices10.1364/AO.37.005271 ↗
88. CRC Handbook of Chemistry and Physics, 96th Edition, CRC Press/Taylor and Francis, Boca Raton, FL, 2016.
89. Adachi · 2012
90. Structure, refractive-index dispersion and the optical absorption edge of chemically deposited ZnxCd(1−x)S thin films10.1007/s003390100877 ↗
91. Controlling the optical properties of plasmonic disordered nanohole silver films10.1021/nn901734d ↗
92. Comparative analysis of opto-electronic performance of aluminium and silver nano-porous and nano-wired layers10.1364/OE.23.026794 ↗
93. Estimation of the volume resistivity of electrically conductive composites10.1002/pc.10324 ↗
94. Evaluating conducting network based transparent electrodes from geometrical considerations10.1063/1.4939280 ↗
95. Morphology and electrical resistivity of metallic nanostructures10.1016/j.mejo.2005.02.068 ↗
96. Electron mean free path model for rectangular nanowire, nanofilm and nanoparticle10.1016/j.physb.2014.01.002 ↗
97. Developing a theoretical relationship between electrical resistivity, temperature, and film thickness for conductors10.1186/1556-276X-6-636 ↗
98. Thickness dependent electrical resistivity of ultrathin (<40 nm) Cu films10.1016/S0040-6090(00)01818-6 ↗
99. Size-dependent resistivity of nanometric copper wires10.1103/PhysRevB.74.045411 ↗
100. Modeling and simulation of resistivity of nanometer scale copper10.1016/j.microrel.2005.09.004 ↗