journal article·2020-09Open access

Oxide route for production of Cu2ZnSnS4 solar cells by pulsed laser deposition

Mungunshagai Gansukh, Simón López Mariño, Moises Espindola Rodriguez, Sara Lena Josefin Engberg, Filipe Mesquita Alves Martinho, Alireza Hajijafarassar, Niels Christian Schjødt, Eugen Stamate, Ole Hansen, Jørgen Schou, Stela Canulescu

Abstract

Abstract In this work, we have investigated Cu2ZnSnS4 (CZTS) solar cells made from oxide, oxy-sulfide and sulfide precursors produced by pulsed laser deposition (PLD). Although sulfide precursors are widely used to fabricate CZTS solar cells, Sn loss is commonly observed due to the high volatility of SnxSy species during high temperature sulfurization. This can lead to a non-ideal absorber composition and a high density of detrimental Sn-related defects that severely affect the performance of the device. By using oxide precursors, we have shown that the Sn loss can be significantly reduced due to the higher thermal stability of SnxOy species when compared to their sulfide counterparts. However, the reaction mechanism for the oxide route results in rough CZTS films. We hypothesize that the SO2 gas that forms during the conversion from oxide to sulfide is trapped in the film during sulfurization, and can lead to grains with hollow cavities and thus increase the surface roughness. Therefore, we have developed an annealing route for the oxide precursors at lower annealing pressures, which leads to improved film morphology and device performance. As a result, we report a power conversion efficiency of 5.4% for solar cells made from oxide precursors. This is the highest value reported for a CZTS absorber produced by PLD.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Chalcogenide Semiconductor Thin Films · Quantum Dots Synthesis And Properties · Copper-based nanomaterials and applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (47)

Show source-provided references
1. Development of thin film solar cell based on Cu2ZnSnS4 thin films10.1016/S0927-0248(00)00088-X ↗
2. Electrical and optical properties of stannite-type quaternary semiconductor thin films10.1143/JJAP.27.2094 ↗
3. Enhanced conversion efficiencies of Cu2ZnSnS4-based thin film solar cells by using preferential etching technique10.1143/APEX.1.041201 ↗
4. Synthesis and characterization of Cu2ZnSnS4 absorber layers by an electrodeposition-annealing route10.1016/j.tsf.2008.11.022 ↗
5. Cu2ZnSnS4 solar cells with over 10% power conversion efficiency enabled by heterojunction heat treatment10.1038/s41560-018-0206-0 ↗
6. Device characteristics of CZTSSe thin-film solar cells with 12.6% efficiency10.1002/aenm.201301465 ↗
7. Identification of killer defects in kesterite thin-film solar cells10.1021/acsenergylett.7b01313 ↗
8. Classification of lattice defects in the kesterite Cu2ZnSnS4 and Cu2ZnSnSe4 earth-abundant solar cell absorbers10.1002/adma.201203146 ↗
9. Is the Cu/Zn disorder the main culprit for the voltage deficit in kesterite solar cells?10.1002/aenm.201502276 ↗
10. Direct liquid coating of chalcopyrite light-absorbing layers for photovoltaic devices10.1002/ejic.200900837 ↗
11. On the Sn loss from thin films of the material system Cu-Zn-Sn-S in high vacuum10.1063/1.3273495 ↗
12. Sublimation study of the tin sulphides SnS2, Sn2S3 and SnS10.1016/0925-8388(91)90053-X ↗
13. The consequences of kesterite equilibria for efficient solar cells10.1021/ja111713g ↗
14. Preparation of Cu2ZnSnS4-based thin film solar cells by a combustion method10.1016/j.solmat.2015.11.027 ↗
15. Influence of treatment conditions on chalcopyrite films deposited at atmospheric pressure
16. 6% Efficiency Cu2ZnSnS4-based thin film solar cells using oxide precursors by open atmosphere type CVD10.1039/c2jm16454j ↗
17. Pulsed laser deposition of Cu2ZnSn(SxSe1-x)4 thin film solar cells using quaternary oxide target prepared by combustion method10.1016/j.solmat.2016.06.022 ↗
18. Cu2ZnSnSxO4-x and Cu 2ZnSnSxSe4-x: first principles simulations of optimal alloy configurations and their energies10.1063/1.4876447 ↗
19. Monolithic thin-film chalcogenide–silicon tandem solar cells enabled by a diffusion barrier10.1016/j.solmat.2019.110334 ↗
20. Fabrication of monolithic CZTS/Si tandem cells by development of the intermediate connection10.1016/j.solener.2019.08.029 ↗
21. Mechanisms of the laser plume expansion during the ablation of LiMn2O410.1063/1.3095687 ↗
22. Nonstoichiometric transfer during laser ablation of metal alloys
23. Ultra-thin Cu2ZnSnS4 solar cell by pulsed laser deposition10.1016/j.solmat.2017.03.002 ↗
24. Pulsed laser deposition of chalcogenide sulfides from multi- and single-component targets: the non-stoichiometric material transfer10.1007/s00339-017-1475-3 ↗
25. Impact of Sn(S, Se) secondary phases in Cu2ZnSn(S, Se)4 solar cells: a chemical route for their selective removal and absorber surface passivation10.1021/am502609c ↗
26. On performance limitations and property correlations of Al-doped ZnO deposited by radio-frequency sputtering10.1088/0022-3727/49/29/295101 ↗
27. Selective detection of secondary phases in Cu2ZnSn(S, Se)4 based absorbers by pre-resonant Raman spectroscopy
28. Discrimination and detection limits of secondary phases in Cu2ZnSnS4 using X-ray diffraction and Raman spectroscopy10.1016/j.tsf.2014.08.028 ↗
29. Atmospheric pressure chemical vapor deposition of tin sulfides (SnS, Sn2S3, and SnS2) on glass10.1021/cm990005z ↗
30. Oxygen vacancy density-dependent transformation from infrared to Raman active vibration mode in SnO2 nanostructures10.1364/OL.36.004296 ↗
31. Determination of surface oxygen vacancy position in SnO2 nanocrystals by Raman spectroscopy10.1016/j.ssc.2011.03.029 ↗
32. Significantly enhanced dye removal performance of hollow tin oxide nanoparticles via carbon coating in dark environment and study of its mechanism10.1186/1556-276X-9-442 ↗
33. Oxide-induced grain growth in CZTS nanoparticle coatings10.1039/C7RA04128D ↗
34. The importance of back contact modification in Cu2ZnSnSe4 solar cells: the role of a thin MoO2 layer10.1016/j.nanoen.2016.06.034 ↗
35. Alkali doping strategies for flexible and light-weight Cu2ZnSnSe4 solar cells10.1039/C5TA09640E ↗
36. Fabrication of Cu2ZnSnS4 thin films using oxides nanoparticles ink for solar cell10.1016/j.jpowsour.2014.11.112 ↗
37. Classification of lattice defects in the kesterite Cu2ZnSnS4 and Cu2ZnSnSe4 earth-abundant solar cell absorbers10.1002/adma.201203146 ↗
38. Phase stability of the Cu-Sn-S system and optimal growth conditions for earth-abundant Cu2SnS3 solar materials10.1016/j.solener.2017.07.017 ↗
39. Chemical insights into the instability of Cu2ZnSnS4 films during annealing10.1021/cm202379s ↗
40. CIS and CIGS layers from selenized nanoparticle precursors
41. 12.4% Efficient Cu(In,Ga)Se2 solar cell prepared from one step electrodeposited Cu-In-Ga oxide precursor layer10.1016/j.solmat.2013.07.053 ↗
42. Electrochemical study of one-step electrodeposition of copper-indium- gallium alloys in acidic conditions as precursor layers for Cu(In,Ga)Se2 thin film solar cells10.1016/j.electacta.2011.05.033 ↗
43. Synthesis of Cu(In,Ga)Se2 absorber using one-step electrodeposition of Cu-In-Ga precursor
44. Low cost oxide-based deposition of Cu2FeSnS4 thin films for photovoltaic absorbers10.1016/j.matchemphys.2016.12.024 ↗
45. Influence of treatment conditions on chalcopyrite films deposited at atmospheric pressure
46. Wide band gap Cu2SrSnS4 solar cells from oxide precursors10.1021/acsaem.9b01322 ↗
47. 10.3% efficient CuIn(S,Se)2 solar cells from DMF molecular solution with the absorber selenized under high argon pressure10.1002/solr.201800044 ↗