Transition from silver-to copper-based screen printed SHJ solar cells
Source abstract
Abstract
In this work, we demonstrate the possibility to reduce silver consumption for highly efficient silicon heterojunction (SHJ) cells by screen printing using low temperature paste based on silver, silver-coated copper or pure copper particles. The achieved grid fingers were characterized towards the line and contact resistance as well as the printed width. The most promising pastes with silver or silver-coated-copper particles allow printing of 35 μm narrow fingers with low line resistance of well below 10 Ω/cm. Simulations show that the achieved grid fingers, lead to very low silver consumption. Comparing cost to efficiency optimization shows that the most cost-effective cell has substantially lower efficiency. This might enable the introduction of alternative low silver or silver-free metallization techniques. To show the currently available options to save silver in screen printed busbarless SHJ cells, samples were produced with specific silver consumption of 7.5 mg/W and even below 5 mg/W if the rear side was realized with a pure copper paste. In another test, silver-based cells with same level of efficiency, improved bifaciality and reduced silver laydown (1/3 compared to reference) around 8 mg/W were successfully introduced into modules. • The silver utilization compares Ag consumption in Ag and AgCu pastes for SHJ cells. • Challenges in transition from Ag to AgCu pastes: fine line and contact resistivity. • Cost optimizations reduced efficiency by 0.4 % but lowers Ag consumption by 3 mg/W. • Low Ag consumption of less than 5 mg/W was achieved for Ag/Cu cells. • Advancements in technology will help to achieve Ag consumption goals for SHJ.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Silicon and Solar Cell Technologies · Photovoltaic System Optimization Techniques · solar cell performance optimization
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (34)
Show source-provided references
1. The role of silver in terawatt PV production - perspectives and options
2. Sustainability strategies for PV: framework, status and needs10.1051/epjpv/2021005 ↗
3. Design considerations for multi-terawatt scale manufacturing of existing and future photovoltaic technologies: challenges and opportunities related to silver, indium and bismuth consumption10.1039/D1EE01814K ↗
4. Future challenges for photovoltaic manufacturing at the terawatt level10.1063/5.0020380 ↗
5. Silver‐lean metallization and hybrid contacts via plating on screen‐printed metal for silicon solar cells manufacturing
6. Fast screen printing and curing process for silicon heterojunction solar cells
7. Progress on the reduction of silver consumption in metallization of silicon heterojunction solar cells10.1016/j.solmat.2023.112620 ↗
8. Nakamura · 2018
9. Thermal stable high‐efficiency copper screen printed back contact solar cells10.1002/solr.202200874 ↗
10. R. Kopecek et al., "Interdigitated Back Contact Technology as Final Evolution for Industrial Crystalline Single-Junction Silicon Solar Cell,".
11. Screen printable, non-fire-through copper paste applied as busbar metallization for back contact solar cells
12. Improvement of solder interconnections applied on back contact solar cells with low-temperature copper paste busbars10.1016/j.solmat.2023.112603 ↗
13. Printing technologies for silicon solar cell metallization: a comprehensive review10.1002/pip.3674 ↗
14. 2024 · vol. 14
15. 2023
16. Rotary screen printed metallization of heterojunction solar cells: toward high‐throughput production with very low silver laydown10.1002/ente.202200377 ↗
17. FlexTrail printing as direct metallization with low silver consumption for silicon heterojunction solar cells: evaluation of solar cell and module performance10.1002/ente.202200702 ↗
18. Applications of parallel dispensing in PV metallization
19. Filament stretching during parallel dispensing – a way to reduce silver consumption in SHJ metallization10.1016/j.solmat.2022.111871 ↗
20. Dispensing of low-temperature silver pastes
21. A. Lachowicz et al., "Project Ameliz: Patterning Techniques for Copper Electroplated Metallization on Heterojunction Solar Cells,".
22. Formation of a copper contact grid on the surface of silicon heterojunction solar cells10.1134/S1063782623090014 ↗
23. Native oxide barrier layer for selective electroplated metallization of silicon heterojunction solar cells10.1002/solr.201900006 ↗
24. Copper-plating metallization with alternative seed layers for c-Si solar cells embedding carrier-selective passivating contacts10.1109/JPHOTOV.2019.2957671 ↗
25. Hatt · 2021
26. T. Tang et al., "Achievement of 25.54% Power Conversion Efficiency by Optimization of Current Losses at the Front Side of Silicon Heterojunction Solar Cells,".
27. Process challenges of high-performance silicon heterojunction solar cells with copper electrodes10.1016/j.solmat.2022.112057 ↗
28. Characterization of copper diffusion in silicon solar cells10.1016/j.egypro.2015.03.292 ↗
29. Project "FINALE" - screen and printing process development for ultra-fine-line contacts below 20μm finger width
30. Progress with screen printed metallization of silicon solar cells - towards 20 μm line width and 20 mg silver laydown for PERC front side contacts10.1016/j.solmat.2022.111804 ↗
31. Analytical modeling of industrial-related silicon solar cells10.1109/JPHOTOV.2013.2281105 ↗
32. Tang · 2023
33. Assessing current-voltage measurements of busbarless solar cells10.1016/j.solmat.2022.111988 ↗
34. Interconnection of low-temperature metallization on silicon solar cells - the role of silver in tin-bismuth-based solder alloys10.1016/j.solmat.2025.113488 ↗