Effect of Cr on stress corrosion behavior of typical pressure vessel materials in molten salt environment
Source abstract
Abstract
In order to study the effect of Cr content on the corrosion and stress corrosion cracking behaviors of alloys after high-temperature molten salt corrosion , three typical pressure vessel materials Q345, 15CrMo, P91 with different Cr contents were tested in this paper. The corrosion behavior and the mechanical properties after high-temperature molten salt corrosion were obtained by uniaxial tensile tests and constant displacement stress corrosion tests . The results show that the corrosion resistance of the materials increases with the increase of Cr content. With the increase of temperature, the corrosion products of low Cr content alloys were sparse granular, and the corrosion product layer of high Cr content alloy was thin and uniform. The results of uniaxial tensile tests indicate that with the decrease of Cr content, the mechanical properties of the corroded materials showed unstable performance, Cr content affects the ductility greatly. After 565 °C molten salt corrosion , the ductility of Q345 is nearly lost. The strength and ductility properties of 15CrMo are relatively stable up to 450 °C, however, when the corrosion temperature is above 500 °C, the mechanical properties begin to fluctuate. P91 exhibits good performance in high temperature molten salt corrosion environments. The crack initial and growth behaviors of the crack tip change significantly under the coupling interaction of stress and high temperature molten salt. The increase of Cr content aggravates the loss of fracture toughness . The fracture toughness J Q of 15CrMo and P91 are 99.86 kN/m and 45.66 kN/m, respectively.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Mechanical Failure Analysis and Simulation · High-Temperature Coating Behaviors · Material Properties and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (50)
Show source-provided references
1. Molten salt corrosion mechanisms of nitrate based thermal energy storage materials for concentrated solar power plants: a review10.1016/j.solmat.2019.02.012 ↗
2. Comparative study on high temperature thermal stability of quaternary nitrate-nitrite mixed salt and Solar salt10.1016/j.solmat.2021.111197 ↗
3. Investigation of the corrosion behavior of NiVAl multilayer coatings in hot salt melts10.1016/j.surfcoat.2015.07.045 ↗
4. Comparative review of different influence factors on molten salt corrosion characteristics for thermal energy storage10.1016/j.solmat.2021.111485 ↗
5. Determination of failure pressure modes of the API specification 12F shop-welded, flat-bottom tanks10.1115/1.4036430 ↗
6. Radiative cooling coupled with latent heat storage for dynamic thermal management10.1016/j.solmat.2024.113173 ↗
7. Solar thermal irradiation cycles and their influence on the corrosion behaviour of stainless steels with molten salt used in concentrated solar power plants10.1016/j.solmat.2022.112141 ↗
8. Study on subgrain boundaries in cast monocrystalline silicon10.1016/j.solmat.2024.112845 ↗
9. Investigation on thermal performance of quaternary nitrate-nitrite mixed salt and solar salt under thermal shock condition10.1016/j.renene.2021.05.002 ↗
10. Investigation on thermal performance of eutectic binary nitrate-carbonate molten salt under thermal shock condition10.1016/j.solmat.2023.112314 ↗
11. Advanced heat exchanger development for molten salts10.1016/j.nucengdes.2014.09.026 ↗
12. Corrosion of pure Fe and 310SS beneath ZnCl2-KCl salt film at 450°C
13. An update review of molecular dynamic study on thermal physical properties of molten salt10.1016/j.solmat.2024.112916 ↗
14. Effect of ZnCl2 vapor on high temperature oxidation of pure chromium10.1023/A:1023776615336 ↗
15. Study on corrosion behavior of molten salt on thermal storage system components
16. Effect of surface secarburization on corrosion behavior of GH3535 alloy in molten fluoride salts10.1007/s40195-018-0814-5 ↗
17. Hot corrosion behaviors of 316L stainless steel in LiCl-3%Li2O molten salt
18. Effect of Ta content on high temperature oxidation and hot corrosion resistance of DZ411 superalloy
19. Compatibility of container materials with Cr in molten FLiNaK salt10.1016/j.jfluchem.2014.09.010 ↗
20. Comparative investigation on dynamic hot corrosion behavior of 347H in quaternary molten salt and its nanofluids10.1016/j.solmat.2024.113263 ↗
21. Effect of Na2CO3 content on thermophysical properties, corrosion behaviors of KNO3-NaNO2 molten salt10.1016/j.energy.2024.133378 ↗
22. Hot corrosion behaviour of different ceramics coatings on boiler tube steel at 800 °C temperature10.1007/s40735-020-00461-9 ↗
23. Hot corrosion study of high velocity oxy-fuel (HVOF) sprayed coatings on boiler tube steel in actual coal fired boiler10.52763/PJSIR.PHYS.SCI.61.3.2018.149.155 ↗
24. Evaluation on thermal and mechanical performance of the hot tank in the two-tank molten salt heat storage system10.1016/j.applthermaleng.2019.114775 ↗
25. Hot corrosion behaviour of Hastelloy X and Inconel 625 in an aggressive environment for superalloys for high-temperature energy applications10.1007/s13204-021-02077-y ↗
26. Experimental study on stress corrosion characteristics of steel Q420qD
27. Effects of mechanical stress on high temperature corrosion in molten salt10.1063/1.5117720 ↗
28. Effects of constant load on corrosion cracking of 304 ASS at 600°C in molten salts10.1002/maco.201911369 ↗
29. Stress-assisted corrosion behaviour of Hastelloy N in FLiNaK molten salt environment
30. Corrosion testing device for in-situ corrosion characterization in operational molten salts storage tanks: a516 Gr70 carbon steel performance under molten salts exposure10.1016/j.solmat.2016.06.005 ↗
31. Corrosion performance of alloy 800H and alloy 625 for potential use as molten salts solar receiver materials in concentrating solar power tower plants10.1016/j.est.2022.105824 ↗
32. On the corrosion cracking of austenitic stainless steel in molten solar salt: experiments and modeling10.1016/j.solmat.2022.111983 ↗
33. Environmentally-assisted cracking of electropolished 316L stainless steel in molten FLiNaK salt10.1016/j.jnucmat.2024.155010 ↗
34. 2021
35. 2007
36. 2007
37. Effect of flow rate and SiO2 nanoparticle on dynamic corrosion behavior of stainless steels in molten salt for thermal energy storage10.1016/j.corsci.2021.109952 ↗
38. Corrosion of mild steel in molten sodium nitrate-potassium nitrate eutectic10.1179/bcj.1976.11.1.44 ↗
39. A reversible oxygen electrode in an equimolar KNO3 - NaNO3 melt saturated with sodium peroxide II. A voltammetric study10.1016/0013-4686(76)85062-1 ↗
40. Research progress of molten nitrate salts with application to solar energy utilization
41. Dynamic corrosion behavior of 316L stainless steel in quaternary nitrate-nitrite salts under different flow rates10.1016/j.solmat.2020.110821 ↗
42. Effects of imposed stresses on high temperature corrosion behaviour of T9110.1016/j.corsci.2021.109595 ↗
43. Effects of external stresses on hot corrosion behavior of stainless steel TP347HFG10.1016/j.corsci.2015.11.037 ↗
44. Impacts of applied stresses on high temperature corrosion behavior of HR3C in molten salt10.1007/s11085-014-9522-3 ↗
45. Affects of applied stresses on the isothermal and cyclic high-temperature oxidation behavior of superalloys10.1016/j.msea.2010.03.050 ↗
46. Tensile deformation and fracture behavior of an oxide dispersion strengthened copper alloy
47. Enhanced high‐temperature strength of a low‐density dispersion‐strengthened Fe–Mn–Al–C steel10.1002/adem.202101192 ↗
48. Improvement of mechanical properties and corrosion resistance of as‐extruded Mg–2Zn–2Al–0.3Mn alloy through Y addition
49. Differences of the high-temperature corrosion of ferrite steel T92 caused by applied stresses and NaCl–Na2SO4 molten salts10.1002/maco.202011669 ↗
50. Effects of external stress on high-temperature corrosion behavior of T92 ferrite steel with Na2SO4-K2SO4 molten salts10.1007/s11085-021-10084-1 ↗